RVRoelof Vos

Roelof Vos

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Roelof Vos has a total of 100 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Control surface allocation based on offline handling quality simulations for a flying wing aircraft

    by Salvatore Asaro, Direnc Atmaca, Erik-Jan van Kampen, Roelof Vos

    Commercial applications of flying wing aircraft, such as the Flying-V considered herein, can contribute to reducing carbon and nitrogen emissions produced by the aviation sector. However, because of the lack of a tail, all flying wing aircraft have reduced controllability. For this reason, the placement and sizing of the control surfaces along the wing is a nontrivial problem. The paper focuses on solving this problem using offline handling quality simulations based on certification requirements. In different flight conditions, the aircraft must be able to perform a set of maneuvers as defined by the certification specifications. First, offline simulations calculate the minimum control authority required from the elevator, aileron, and rudder to perform each maneuver. Then, based on the global minimum for all maneuvers, the control surfaces are sized and placed along the wings. The aerodynamic model employed uses a combination of Reynolds-averaged Navier–Stokes (RANS) and vortex lattice method (VLM) simulations. The control authority of the control surfaces is estimated with VLM and VLM calibrated with RANS simulations, showing significant differences between the two.


  • Open Access

    Hydrogen, medium-range airplane design optimization for minimal global warming impact

    by P. Proesmans, Roelof Vos

    This paper focuses on the conceptual design optimization of liquid hydrogen aircraft and their performance in terms of climate impact, cash operating cost, and energy consumption. An automated, multidisciplinary design framework for kerosene-powered aircraft is extended to design liquid hydrogen-powered aircraft at a conceptual level. A hydrogen tank is integrated into the aft section of the fuselage, increasing the operating empty mass and wetted area. Furthermore, the gas model of the engine is adapted to account for the hydrogen combustion products. It is concluded that for medium-range, narrow-body aircraft using hydrogen technology, the climate impact can be minimized by flying at an altitude of 6.0 km at which contrails are eliminated and the impact due to $$\hbox {NO}_{\textrm{x}}$$ NO x emissions is expected to be small. However, this leads to a deteriorated cruise performance in terms of energy and operating cost due to the lower lift-to-drag ratio (– 11%) and lower engine overall efficiency (– 10%) compared to the energy-optimal solutions. Compared to cost-optimal kerosene aircraft, the average temperature response can be reduced by 73–99% by employing liquid hydrogen, depending on the design objective. However, this reduction in climate impact leads to an increase in cash operating cost of 28–39% when considering 2030 hydrogen price estimates. Nevertheless, an analysis of future kerosene and hydrogen prices shows that this cost difference can be significantly decreased beyond 2030.


  • Top Cited Papers
    Open Access

    Aerodynamic interaction between propellers of a distributed-propulsion system in forward flight

    by Reynard de Vries, Nando van Arnhem, Tomas Sinnige, Roelof Vos, Leo L.M. Veldhuis


  • Open Access

    Engineering Method to Estimate the Blade Loading of Propellers in Nonuniform Flow

    by Nando van Arnhem, Reynard de Vries, Tomas Sinnige, Roelof Vos, Georg Eitelberg, Leo L. M. Veldhuis

    Advances in aerodynamic and propulsive efficiency of future aircraft can be achieved by strategic installation of propellers near the airframe. This paper presents a robust and computationally effi...


  • Experimental Aerodynamic Analysis of a 4.6%-Scale Flying-V Subsonic Transport

    by Marco Palermo, Roelof Vos

    The experimental investigation into the aerodynamic characteristics of a 4.6%-scale half-model of a flying-wing transport aircraft is detailed. The study is performed in an open-jet wind tunnel where forces and moments are recorded using a 6-axis balance. Two control surfaces in the outboard wing are deflected to measure their effect in terms of lift, drag, and pitching moment up to a Reynolds number of 1 million. The results are subsequently combined with the estimated thrust force using a flight mechanics model of the aircraft in order to predict the most forward and most aft center-of-gravity locations for which the aircraft can be balanced with the control surfaces, while still being statically stable. The results show that the aircraft can attain an untrimmed maximum lift coefficient of 1.02 at an angle of attack of 35 degrees. Furthermore, the pitching moment around the leading-edge of the mean geometric chord is negatively correlated to the angle of attack up to 19 degrees, after which a strong pitch-break is observed, making the aircraft statically unstable. This is associated with a forward shift of the aerodynamic center to a longitudinal position 35% of the mean geometric chord (MGC) ahead of the moment reference point which is caused by the formation of strong vortices over the wing surface. The effectiveness of the control surfaces hardly deteriorates with angle of attack and all three control surfaces are shown to be effective up to the maximum lift coefficient. Analysis shows that the center-of-gravity location should reside between [-7.5; 0.5] %MGC, in power-off conditions, and between [-6; 1] %MGC, in power-on conditions, from the leading edge of the mean geometric chord to ensure an ultimate static stability margin of 4.4% as well and a minimum landing speed of 20 m/s. Within these ranges, trimmed maximum lift coefficient values of 0.68 and 0.66 can be achieved respectively in power-off and power-on conditions.


  • Synthesis of Aero-Propulsive Interaction Studies Applied to Conceptual Hybrid-Electric Aircraft Design

    by Maurice Hoogreef, Reynard de Vries, Tomas Sinnige, Roelof Vos

    This paper presents a synthesis of aero-propulsive interaction studies performed at Delft University of Technology, applied to conceptual aircraft designs with distributed hybrid-electric propulsion. The studied aero-propulsive interactions include tip-mounted propulsion, wing leading edge distributed propulsion and boundary-layer-ingestion combined with different aircraft layouts. This article starts with a description of the applied design framework and an overview of the models to include the aero-propulsive interactions as well as hybrid powertrains. Subsequently, applications of the different aero-propulsive interactions to several propulsion-system configurations are presented for configurations with distributed hybrid-electric propulsion with a partial turbo-electric (hybrid) powertrain. These case studies are sized for a set of top-level requirements covering the range from regional turboprop to typical narrow-body turbofan aircraft. The results identify directions of future detailed investigations and top-level requirements for more sustainable aircraft (in terms of fuel and energy consumption). Results indicate that lower shaft power ratios show better performance, with (unoptimized) DHEP technologies approaching their respective reference aircraft. The shaft power ratio has a significant effect on both PREE and MTOM, and it was shown that beyond 20% shaft power ratio, the PREE decreases and MTOM increases much more than between 10% and 20% indicating a possible local optimum between the latter two values as even lower values did not yield any significant improvements. Tip-mounted propulsion is constrained by the relatively high cruise Mach number of 0.6 by the tip Mach number. It is also shown that longer ranges lead to a higher PREE, especially for those aircraft with a secondary power train that over a longer cruise can overcome their mass penalties. At the high range case for Mach 0.5, it can be seen that the distributed propulsion systems show the largest improvement.


  • Aero-Propulsive Efficiency Requirements for Turboelectric Transport Aircraft

    by Reynard de Vries, Maurice Hoogreef, Roelof Vos, Tomas Sinnige, Higor Luis Silva, Thiago A. Guimarães, Ralph Jansen, Kirsten P. Duffy, Kurt P. Rouser, Nicholas Lucido, et al.

    In this paper a design-of-experiments is performed with the objective of determining the improvements in aeropropulsive efficiency required for a reduction in the energy consumption of turboelectric transport aircraft, when compared to conventional, gas-turbine based alternatives. Simplified representations of the powertrain and the aeropropulsive interaction effects are used, such that the results are independent of the design of the electrical system or the external layout of the propulsion-system. An evaluation of different mission requirements confirms that the turboelectric architecture presents the largest benefit for long ranges, and that the aeropropulsive benefit required for a predefined reduction in energy consumption increases with increasing cruise Mach number. Moreover, the impact of different technology maturity levels of the electrical drivetrain components is assessed. The results show that the shaft power ratio necessary to achieve a determined aeropropulsive benefit is a decisive factor, and that for a shaft power ratio of 20%, a 5% reduction in energy consumption is possible on the mid-term (circa 2035) if an 11% increase in aeropropulsive efficiency is achieved. A 15% reduction in energy consumption is only possible with extremely optimistic powertrain technology assumptions, and requires and increase in aeropropulsive efficiency of at least 14%, for the missions considered.


  • A Comparison of Hybrid-Electric Aircraft Sizing Methods

    by D. Felix Finger, Reynard de Vries, Roelof Vos, Carsten Braun, Cees Bil

    The number of case studies focusing on hybrid-electric aircraft is steadily increasing, since these configurations are thought to lead to lower operating costs and environmental impact than traditional aircraft. However, due to the lack of reference data of actual hybrid-electric aircraft, in most cases, the design tools and results are difficult to validate. In this paper, two independently developed approaches for hybrid-electric conceptual aircraft design are compared. An existing 19-seat commuter aircraft is selected as the conventional baseline, and both design tools are used to size that aircraft. The aircraft is then re-sized under consideration of hybrid-electric propulsion technology. This is performed for parallel, serial, and fully-electric powertrain architectures. Finally, sensitivity studies are conducted to assess the validity of the basic assumptions and approaches regarding the design of hybrid-electric aircraft. Both methods are found to predict the maximum take-off mass (MTOM) of the reference aircraft with less than 4% error. The MTOM and payload-range energy efficiency of various (hybrid-) electric configurations are predicted with a maximum difference of approximately 2% and 5%, respectively. The results of this study confirm a correct formulation and implementation of the two design methods, and the data obtained can be used by researchers to benchmark and validate their design tools.


  • The Effect of Engine Location on the Aerodynamic Efficiency of a Flying-V Aircraft

    by Berta Rubio Pascual, Roelof Vos

    The Flying-V is a novel flying wing concept where the main lifting surface has been fully integrated with the passenger cabin. This study focuses on the effect of engine positioning on aerodynamic interference under regulatory and structural constraints. An initial benchmark for the lift-to-drag ratio is obtained from a baseline Flying-V configuration, and the influence of the x, y and z position, as well as engine orientation are subsequently analysed. An Euler solver on a three-dimensional, unstructured grid is used to model the flow at cruise condition: M=0.85, h=13,000 m, alpha=2.9 degrees, and a thrust per engine of 50 kN. The viscous drag contribution is computed using an empirical method. A total of forty different engine locations are tested under these conditions to build a surrogate model that predicts the aircraft's lift-to-drag ratio based on the position of the engine. The results obtained show that misplacing the engine can lead to significant lift-to-drag ratio losses going as high as 55\% when compared against the ideal integration configuration. A region behind the airframe's trailing edge is identified where the interference losses due to the installation are minimized. At this location, engine installation causes a 10% penalty in aerodynamic efficiency, a minimum one-engine-inoperative yawing moment and a small thrust-induced pitching moment.