Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Grzegorz Sobczak has a total of 59 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Enhanced performance of quantum cascade lasers through active region optimization and large optical cavity engineering

    by Kamil Pierściński, Dorota Pierścińska, Katarzyna Pieniak, Dominika Niewczas, Iwona Sankowska, Grzegorz Sobczak, Artur Broda

    This paper presents a comprehensive study of mid-infrared quantum cascade lasers (QCLs) designed with optimized active region geometries and large optical cavity (LOC) structures to achieve enhanced performance. The devices were fabricated using molecular beam epitaxy (MBE) and characterized in terms of electro-optical, spectral, and far-field properties. The introduction of LOC architectures significantly reduced waveguide losses, improved optical confinement, and enhanced beam collimation. Devices with 50 active region stages and LOC design (QCL#3_LOC) exhibited the lowest waveguide losses (∼1.9 cm −1 ) and the narrowest vertical far-field divergence (FWHM = 27.1°), while maintaining stable emission around 5.3 µm. Compared to conventional designs, the optimized structures achieved nearly four times higher output power (up to 3 W) and a reduced threshold current density (∼2.5 kA/cm 2 ), with a wall-plug efficiency exceeding 4%. Spectral measurements revealed narrower electroluminescence linewidths and reduced current-induced redshift, confirming improved carrier uniformity and thermal management. These results demonstrate that combining active region optimization with LOC engineering provides a powerful route to increased performance and reliability of mid-infrared QCLs, making them promising candidates for high-power applications such as gas sensing, spectroscopy, and free-space optical communication.

  • Open Access

    Calibration Technique for MBE Growth of Long Wavelength InAlAs/InGaAs Quantum Cascade Lasers

    by Piotr Gutowski, Iwona Sankowska, Maciej Bugajski, Grzegorz Sobczak, Aleksandr Kuźmicz, Kamil Pierściński

    In this paper, we present the methodology for precise calibration of the Molecular Beam Epitaxy (MBE) growth process and achieving run-to-run stability of growth parameters. We present the analysis of the influence of fluxes stability during the growth of long wavelength quantum cascade laser structures designed for the range λ ~ 12–16 µm on wavelength accuracy with respect to desired emission wavelength. The active region of the lasers has a complex structure of nanometer thickness InxGa1−xAs/InyAl1−yAs superlattice. As a consequence, the compositional and thickness control of the structure via bulk growth parameters is rather difficult. To deal with this problem, we employ a methodology based on double-superlattice test structures that precede the growth of the actual structures. The test structures are analyzed by High Resolution X-ray Diffraction, which allows calibration of the growth of the complex active region of quantum cascade laser structures. We also theoretically studied the effect of individual flux changes on the emission wavelength and gain parameters of the laser. The results of simulations allow for the determination of flux stability tolerance, preserving acceptable parameters of the laser and providing means of emission wavelength control. The proposed methodology was verified by the growth of laser structures for emission at around 13.5 μm.

  • Open Access

    Calibration Technique for MBE Growth of Long Wavelength InAlAs/InGaAs Quantum Cascade Lasers

    by Piotr Gutowski, Iwona Sankowska, Maciej Bugajski, Grzegorz Sobczak, Aleksandr Kuźmicz, Kamil Pierściński

    In this paper we present methodology for precise calibration of Molecular Beam Epitaxy (MBE) growth process and achieving run to run stability of growth parameters. We present the analysis of the influence of fluxes stability during the growth of long wavelength quantum cascade laser structures designed for the range λ ~ 12–16 µm on wavelength accuracy with respect to desired emission wavelength. The active region of the lasers has a complex structure of nanometer thickness InxGa1-xAs/InyAl1-yAs superlattice. As a consequence, the compositional and thickness control of the structure via bulk growth parameters is rather difficult. To deal with this problem we employ methodology based on double-superlattice test structures, that precede the growth of the actual structures. The test structures are analyzed by high-resolution X-ray diffraction which allows to calibrate the growth of the complex active region of quantum cascade laser structures. We also study theoretically the effect of individual flux changes on emission wavelength and gain parameters of the laser. The results of simulations allow for determination of flux stability tolerance, preserving acceptable parameters of the laser and provide means of emission wavelength control. The proposed methodology was verified by the growth of laser structures for emission at around 13.5 μm.

  • Linewidth Broadening in Short-Wavelength Quantum Cascade Lasers

    by Andrzej Kolek, Grzegorz Hałdaś, Piotr Gutowski, Grzegorz Sobczak, Dorota Pierścińska, Maciej Bugajski

    Nonequilibrium Green’s function modeling of the structure used for III-V quantum cascade lasers emitting at approximately 5-μm wavelength is performed to get insight into and analyze the processes that determine the linewidth of the optical (inter-sub-band) transition. Theoretical results are compared with electroluminescence data collected for real structures. Excellent agreement is found for both the transition energy of approximately 234meV and the linewidth of approximately 32meV, typical for this sort of device. Careful inspection of simulation data shows that, for these structures, the interface-roughness (IR) scattering contributes to the optical linewidth ≅50%. The decreased broadening due to IR scattering is not due to very smooth interfaces, but rather due to the finite carrier concentration and the decreased population of final states k′ available for the initial state k in the limit of vanishing in-plane momentum k→0. Further line narrowing is caused by nonparabolicity coupled with the highly nonthermal occupation of the lower laser sub-band, which destroys the population inversion for the hot carriers.


  • Open Access

    Monolithic, Optically Coupled, Multi-Section Mid-IR Quantum Cascade Lasers

    by Kamil Pierściński, Dorota Pierścińska, Grzegorz Sobczak, Aleksandr Kuźmicz, Krzysztof Chmielewski, Katarzyna Krajewska, Piotr Gutowski

    Mid-infrared (mid-IR λ ≈ 3–12 μm), single-mode-emission Quantum Cascade Lasers (QCLs) are of significant interest for a wide range of applications, especially as the laser sources are chosen for laser absorption spectroscopy. In this work, we present the design, fabrication and characterization of multi-section, coupled-cavity, mid-IR quantum cascade lasers. The purpose of this work is to propose a design modification for a coupled-cavity device, yielding a single-mode emission with a longer range of continuous tuning during the pulse, in contrast to a 2-section device. This effect was obtained and demonstrated in the work. The proposed design of a 3-section coupled-cavity QCL allows for a single-mode emission with 35 dB side-mode suppression ratio. Additionally, the time-resolved spectra of the wavelength shift during pulse operation, show a continuous tuning of ~3 cm−1 during the 2 μs pulse. The devices were fabricated in a slightly modified, standard laser process using dry etching.

  • Open Access

    In-Depth Experimental Analysis of Influence of Electroplated Gold Thickness on Thermal and Electro-Optical Properties of mid-IR AlInAs/InGaAs/InP Quantum Cascade Lasers

    by Dorota Pierścińska, Kamil Pierściński, Grzegorz Sobczak, Katarzyna Krajewska, Krzysztof Chmielewski, Aleksandr Kuźmicz, Krzysztof Piskorski, Piotr Gutowski

    In this paper, we have examined the influence of electroplated gold thickness on the thermal and electro-optical properties of mid-IR AlInAs/InGaAs, InP QCLs. The experimental results show a significant reduction of the temperature of QCL active region (AR) with increasing gold layer thickness. For QCLs with 5.0 μm gold thickness, we observed a 50% reduction of the active region temperature. An improvement of key electro-optical parameters, that is, threshold current density and maximum emitted power for structures with thick gold, was observed. The results of micro-Raman characterization show that the electroplated gold layer introduces only moderate compressive strain in top InP cladding, which is well below the critical value for the creation of misfit dislocations.


  • Open Access

    Coupled Cavity Mid-IR Quantum Cascade Lasers Fabricated by Dry Etching

    by Kamil Pierściński, Dorota Pierścińska, Aleksandr Kuźmicz, Grzegorz Sobczak, Maciej Bugajski, Piotr Gutowski, Krzysztof Chmielewski

    In this work, two-section, coupled cavity, mid-IR quantum cascade lasers (QCLs) were characterized in terms of their tuning range and emission stability under operation towards potential application in detection systems. Devices were processed by inductively coupled plasma reactive ion etching (ICP-RIE) from InP-based heterostructure, designed for emission in the 9.x micrometer range. Single mode devices were demonstrated with a better than 20 dB side mode suppression ratio (SMRS). The fabrication method resulted in improved yield, as well as high repeatability of individual devices. Continuous, mode-hop-free tuning of emission wavelength was observed across ~4.5 cm−1 for the range of temperatures of the heat sink from 15 °C to 70 °C. Using the thermal perturbation in the lasing cavity, in conjunction with controlled hopping between coupled-cavity (CC) modes, we were able to accomplish tuning over the range of up to ~20 cm−1.


  • Open Access

    Optimization of Cavity Designs of Tapered AlInAs/InGaAs/InP Quantum Cascade Lasers Emitting at 4.5 μm

    by Kamil Pierscinski, Aleksandr Kuzmicz, Dorota Pierscinska, Grzegorz Sobczak, Maciej Sakowicz, Piotr Gutowski, Kamil Janus, Krzysztof Chmielewski, Maciej Bugajski

    In this work design, fabrication and characterization of mid-infrared AlInAs/InGaAs/InP QCLs taper quantum cascade lasers are presented. In order to increase output power while keeping good beam quality, taper design of resonator was used. We have studied devices emitting at 4.5 μm with different shapes (linear, concave and convex) and angles of taper waveguide section, to optimize the output beam parameters, namely ${M^{2}}$ and brightness. Experimental results demonstrate that convex geometry taper laser with 1.7° taper shows the best performance, the highest output power up to 5 W and the smallest horizontal beam divergence of 5.6° in the fundamental mode. This design is also characterized by the highest brightness.


  • Degradation of AlInAs/InGaAs/InP quantum cascade lasers due to electrode adhesion failure

    by D. Pierścińska, K. Pierściński, G. Sobczak, P. Gutowski, M. Płuska, M. Bugajski


  • Open Access

    In-junction-plane beam divergence stabilization by lateral periodic structure in wide-stripe laser diodes

    by Andrzej Maląg, Grzegorz Sobczak, Elżbieta Dąbrowska, Marian Teodorczyk

    This paper describes the way to stabilize in-junction-plane optical field distribution and emitted beam divergence in high-power 970-nm-band laser diodes (LDs). This is done by introducing a lateral periodic structure into the LD‟s wide-stripe-waveguide, designed to prefer and stabilize the selected (resonant) high-order lateral mode. According to modeling, in CW operation the gain equalization of lateral modes due to thermal index guiding leads to beam divergence stabilization by incorporating the modes up to the resonant one and cutting out higher ones. This was demonstrated experimentally in a wide drive current range. Such stability of a non-Gaussian laser beam profile with steep slopes can be interesting for many applications. Thanks to the drive current flow control by the periodic structure, the effects typical for conventional wide-stripe LDs, such as lateral current crowding, carrier accumulation at stripe edges and optical far-field blooming are not observed.