Omer Sahin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Omer Sahin has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Volkan Kilicli
Department of Metallurgical and Materials Engineering, Faculty of Technology, Gazi University, Ankara, Turkey
7 shared publications - Burak Nalcaci
Gazi University
3 shared publications - Ahmet Uyar
HACETTEPE ÜNİVERSİTESİ, BAŞKENT ORGANİZE SANAYİ BÖLGESİ TEKNİK BİLİMLER MESLEK YÜKSEKOKULU, MAKİNE VE METAL TEKNOLOJİLERİ BÖLÜMÜ, MAKİNE PR
2 shared publications - Mehmet Erdogan
Gazi University
2 shared publications - Murat Aydin
ESTAS Camshaft Company, Seyh Samil OSB Mah, Sivas, Turkey
2 shared publications - Onur Okur
Department of Metallurgical and Materials Engineering, Faculty of Architecture and Engineering, Kirikkale University, Kirikkale, Turkey
2 shared publications
Latest Publications
- Open Access
- 16 October 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (20) , 206504
Post-aging-induced microstructural, mechanical, and ductile fracture characteristics of 6082-T6 aluminum alloy
In this study, the effects of post-aging conditions on the mechanical properties, deformation behavior, and fracture characteristics of 6082-T6 aluminum alloy sheets were investigated, using tensile testing supported by DIC. Post-aging treatments were performed at 100 °C, 200 °C, 300 °C, and 400 °C, with holding times of 30, 60, and 90 min at each temperature. The following parameters were determined from the tensile tests: yield strength, tensile strength, strain-hardening exponent, uniform elongation, total elongation, and energy absorption capacity. Microstructural and fracture analyses were performed using optical microscopy and scanning electron microscopy, while x-ray diffraction was used to evaluate phase-related structural changes. Hardness variations were assessed by Vickers hardness testing. Fracture-surface dimple morphologies were quantitatively evaluated using average dimple diameter and standard deviation values to assess the temperature- and time-dependent variation in fracture behavior. The results showed that aging at 200 °C for 60 min provided a highly favorable strength–ductility balance and was identified as the most efficient processing condition in terms of the combined mechanical response, with a yield strength of approximately 289 MPa, tensile strength of about 400 MPa, uniform elongation of 15.9%, total elongation of 17.4%, hardness of 115.6 HV, and energy absorption of 61.36 MJ m −3 . At 300 °C–400 °C, pronounced overaging occurred as precipitate coarsening reduced the effectiveness of precipitation strengthening, leading to significant degradation in mechanical performance. The strain-hardening response and energy absorption capacity were found to be strongly dependent on the aging condition. The results indicate a transition from relatively homogeneous deformation to strain-localized behavior as aging temperature increases, consistent with reduced deformation stability at elevated temperatures. Overall, these findings demonstrate that controlled post-aging can tailor the strength–ductility balance and fracture response of AA6082-T6 sheets.
- 16 October 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (20) , 206504
Open AccessPost-aging-induced microstructural, mechanical, and ductile fracture characteristics of 6082-T6 aluminum alloy
In this study, the effects of post-aging conditions on the mechanical properties, deformation behavior, and fracture characteristics of 6082-T6 aluminum alloy sheets were investigated, using tensile testing supported by DIC. Post-aging treatments were performed at 100 °C, 200 °C, 300 °C, and 400 °C, with holding times of 30, 60, and 90 min at each temperature. The following parameters were determined from the tensile tests: yield strength, tensile strength, strain-hardening exponent, uniform elongation, total elongation, and energy absorption capacity. Microstructural and fracture analyses were performed using optical microscopy and scanning electron microscopy, while x-ray diffraction was used to evaluate phase-related structural changes. Hardness variations were assessed by Vickers hardness testing. Fracture-surface dimple morphologies were quantitatively evaluated using average dimple diameter and standard deviation values to assess the temperature- and time-dependent variation in fracture behavior. The results showed that aging at 200 °C for 60 min provided a highly favorable strength–ductility balance and was identified as the most efficient processing condition in terms of the combined mechanical response, with a yield strength of approximately 289 MPa, tensile strength of about 400 MPa, uniform elongation of 15.9%, total elongation of 17.4%, hardness of 115.6 HV, and energy absorption of 61.36 MJ m −3 . At 300 °C–400 °C, pronounced overaging occurred as precipitate coarsening reduced the effectiveness of precipitation strengthening, leading to significant degradation in mechanical performance. The strain-hardening response and energy absorption capacity were found to be strongly dependent on the aging condition. The results indicate a transition from relatively homogeneous deformation to strain-localized behavior as aging temperature increases, consistent with reduced deformation stability at elevated temperatures. Overall, these findings demonstrate that controlled post-aging can tailor the strength–ductility balance and fracture response of AA6082-T6 sheets.
- 16 December 2025
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- No. Advanced O
Östemperleme Sıcaklığının Karbür İçermeyen Beynitik Çelik Dökümün Aşınma Davranışı Üzerine Etkisi
Bu araştırmanın amacı, karbürsüz beynitik çelik döküm (KİB-ÇD) malzemenin mikroyapısal özellikleri ve aşınma performansının, uygulanan östemperleme sıcaklığından ne şekilde etkilendiğini ortaya koymaktır. Bu kapsamda, numuneler öncelikle 900°C sıcaklıkta 60 dakika süreyle östenitleme işlemine tabi tutulmuştur. Ardından, östemperleme aşaması için 275°C, 300°C, 325°C ve 350°C olmak üzere dört farklı sıcaklıkta hazırlanan tuz banyolarında, her bir numune 90 dakika boyunca izotermal olarak bekletilmiştir. Mikroyapısal karakterizasyon, optik mikroskop kullanılarak gerçekleştirilmiştir. Malzeme yapısındaki kalıntı östenit fazının hacimsel oranı ise X-ışını kırınımı (XRD) tekniği ile tespit edilmiştir. Aşınma davranışının belirlenmesi amacıyla, ASTM G133-22 standardında belirtilen prosedürlere uygun olarak aşınma testleri yapılmış ve test sonrası yüzeylerde meydana gelen hacim kayıpları optik profilometre ile hassas bir şekilde ölçülmüştür. Elde edilen bulgular, östemperleme sıcaklığının mikroyapı ve mekanik özellikler üzerinde belirleyici bir rol oynadığını göstermiştir. En ince taneli mikroyapı, 275°C'de gerçekleştirilen 90 dakikalık östemperleme işlemi sonucunda elde edilirken, en kaba taneli yapıya 350°C'de yapılan işlemle ulaşılmıştır. Bu mikroyapısal farklılıklar, malzemenin sertlik değerlerine de yansımıştır. En yüksek sertlik değeri (54,9 HRC) 275°C'de işlem gören numunede ölçülürken, en düşük sertlik (48,2 HRC) 350°C'de östemperlenen numunede kaydedilmiştir. Kalıntı östenit hacim oranı da östemperleme sıcaklığı ile doğru orantılı bir değişim sergilemiştir; en düşük oran (%17,5) 275°C'de, en yüksek oran (%24,2) ise 350°C'de işlem görmüş numunelerde tespit edilmiştir. Aşınma testi sonuçları, ısıl işlemin aşınma direncini önemli ölçüde iyileştirdiğini ortaya koymuştur. Döküm halindeki numune, 0,3304 mm³'lük hacim kaybı ve 1,32x10⁻⁴ mm³/N.m'lik aşınma hızı ile en zayıf performansı göstermiştir. Östemperlenmiş numuneler arasında ise en üstün aşınma direnci, 275°C'de işlem gören numunede gözlemlenmiştir. Bu numune, 6,68x10⁻⁶ mm³/N.m ile en düşük aşınma hızına, 0,0167 mm³ ile en az hacim kaybına ve μ=0,684 ile en düşük ortalama sürtünme katsayısına sahip olmuştur. Buna karşılık, 350°C'de östemperlenen numune, 1,62x10⁻⁵ mm³/N.m'lik aşınma hızı, 0,0406 mm³'lük hacim kaybı ve μ=0,709'luk sürtünme katsayısı ile en yüksek aşınma değerlerini sergilemiştir.
- 16 December 2025
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- No. Advanced O
Östemperleme Sıcaklığının Karbür İçermeyen Beynitik Çelik Dökümün Aşınma Davranışı Üzerine Etkisi
Bu araştırmanın amacı, karbürsüz beynitik çelik döküm (KİB-ÇD) malzemenin mikroyapısal özellikleri ve aşınma performansının, uygulanan östemperleme sıcaklığından ne şekilde etkilendiğini ortaya koymaktır. Bu kapsamda, numuneler öncelikle 900°C sıcaklıkta 60 dakika süreyle östenitleme işlemine tabi tutulmuştur. Ardından, östemperleme aşaması için 275°C, 300°C, 325°C ve 350°C olmak üzere dört farklı sıcaklıkta hazırlanan tuz banyolarında, her bir numune 90 dakika boyunca izotermal olarak bekletilmiştir. Mikroyapısal karakterizasyon, optik mikroskop kullanılarak gerçekleştirilmiştir. Malzeme yapısındaki kalıntı östenit fazının hacimsel oranı ise X-ışını kırınımı (XRD) tekniği ile tespit edilmiştir. Aşınma davranışının belirlenmesi amacıyla, ASTM G133-22 standardında belirtilen prosedürlere uygun olarak aşınma testleri yapılmış ve test sonrası yüzeylerde meydana gelen hacim kayıpları optik profilometre ile hassas bir şekilde ölçülmüştür. Elde edilen bulgular, östemperleme sıcaklığının mikroyapı ve mekanik özellikler üzerinde belirleyici bir rol oynadığını göstermiştir. En ince taneli mikroyapı, 275°C'de gerçekleştirilen 90 dakikalık östemperleme işlemi sonucunda elde edilirken, en kaba taneli yapıya 350°C'de yapılan işlemle ulaşılmıştır. Bu mikroyapısal farklılıklar, malzemenin sertlik değerlerine de yansımıştır. En yüksek sertlik değeri (54,9 HRC) 275°C'de işlem gören numunede ölçülürken, en düşük sertlik (48,2 HRC) 350°C'de östemperlenen numunede kaydedilmiştir. Kalıntı östenit hacim oranı da östemperleme sıcaklığı ile doğru orantılı bir değişim sergilemiştir; en düşük oran (%17,5) 275°C'de, en yüksek oran (%24,2) ise 350°C'de işlem görmüş numunelerde tespit edilmiştir. Aşınma testi sonuçları, ısıl işlemin aşınma direncini önemli ölçüde iyileştirdiğini ortaya koymuştur. Döküm halindeki numune, 0,3304 mm³'lük hacim kaybı ve 1,32x10⁻⁴ mm³/N.m'lik aşınma hızı ile en zayıf performansı göstermiştir. Östemperlenmiş numuneler arasında ise en üstün aşınma direnci, 275°C'de işlem gören numunede gözlemlenmiştir. Bu numune, 6,68x10⁻⁶ mm³/N.m ile en düşük aşınma hızına, 0,0167 mm³ ile en az hacim kaybına ve μ=0,684 ile en düşük ortalama sürtünme katsayısına sahip olmuştur. Buna karşılık, 350°C'de östemperlenen numune, 1,62x10⁻⁵ mm³/N.m'lik aşınma hızı, 0,0406 mm³'lük hacim kaybı ve μ=0,709'luk sürtünme katsayısı ile en yüksek aşınma değerlerini sergilemiştir.
- 5 December 2025
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 68 (1) , 37-49
Comparison of dry sliding wear behavior and microstructural properties of AISI 8620 steel after gas carburization, gas nitriding, and pack boronization surface treatments
AISI 8620 steel is used in gears and machine parts where surface wear resistance is important. The presented study focuses on different surface hardening treatments on microstructural properties and the dry sliding wear behavior of the AISI 8620 steel. The dry sliding wear test used a tribometer with constant wear test parameters according to ASTM G-99 standard. The microstructures were characterized by optical and scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), and X-ray diffraction (XRD). The highest surface hardness (∼1,507 HV) occurs in the boronized sample, attributed to the hard, iron borides (FeB, Fe 2 B, Fe 3 B) layers. The minimum surface hardness (∼507 HV) is determined in nitrided samples. The maximum case hardening depth (∼0.90 mm) is obtained in nitrided samples, as the minimum value of case depth (∼0.1 mm) was found in boronized samples. The mean coefficient of friction was highest for nitrided (0.622) and lowest for boronized (0.367) samples. Boronizing also gave the minimum wear (1.705 mm 3 , 1 mg), compared with nitriding (13.5 mm 3 , 1.8 mg) and carburizing (43.57 mm 3 , 4.9 mg). The boronized samples exhibited the best wear properties. According to the optical profilometer results of worn samples; the carburized sample exhibits a broad and deep wear track (volume loss 43.57 mm 3 ), indicating severe abrasive wear due to lower surface hardness, the boronized sample showed the narrowest and shallowest wear track (volume loss 1.705 mm 3 ), because of superior wear resistance from the dense, hard iron boride layer while the nitrided sample having moderate wear depth and volume loss (13.5 mm 3 ), indicating intermediate wear resistance attributed to a thinner, harder nitride layer providing moderate protection.
- 5 December 2025
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 68 (1) , 37-49
Comparison of dry sliding wear behavior and microstructural properties of AISI 8620 steel after gas carburization, gas nitriding, and pack boronization surface treatments
AISI 8620 steel is used in gears and machine parts where surface wear resistance is important. The presented study focuses on different surface hardening treatments on microstructural properties and the dry sliding wear behavior of the AISI 8620 steel. The dry sliding wear test used a tribometer with constant wear test parameters according to ASTM G-99 standard. The microstructures were characterized by optical and scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), and X-ray diffraction (XRD). The highest surface hardness (∼1,507 HV) occurs in the boronized sample, attributed to the hard, iron borides (FeB, Fe 2 B, Fe 3 B) layers. The minimum surface hardness (∼507 HV) is determined in nitrided samples. The maximum case hardening depth (∼0.90 mm) is obtained in nitrided samples, as the minimum value of case depth (∼0.1 mm) was found in boronized samples. The mean coefficient of friction was highest for nitrided (0.622) and lowest for boronized (0.367) samples. Boronizing also gave the minimum wear (1.705 mm 3 , 1 mg), compared with nitriding (13.5 mm 3 , 1.8 mg) and carburizing (43.57 mm 3 , 4.9 mg). The boronized samples exhibited the best wear properties. According to the optical profilometer results of worn samples; the carburized sample exhibits a broad and deep wear track (volume loss 43.57 mm 3 ), indicating severe abrasive wear due to lower surface hardness, the boronized sample showed the narrowest and shallowest wear track (volume loss 1.705 mm 3 ), because of superior wear resistance from the dense, hard iron boride layer while the nitrided sample having moderate wear depth and volume loss (13.5 mm 3 ), indicating intermediate wear resistance attributed to a thinner, harder nitride layer providing moderate protection.
- Open Access
- 12 October 2025
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 28 (5) , 1535-1543
Effects of Heat Treatment Time on Properties of 1% Fe-Doped ZnO Films Fabricated by Ultrasonic Spray Pyrolysis
In this study, 1% Fe-doped ZnO thin films were deposited using Ultrasonic Spray Pyrolysis (USP) to examine their structural, morphological, and photocatalytic properties. Heat treatment was applied to 1% Fe-doped ZnO thin films produced with USP at 500 ºC for different times (1, 3, and 5 hours). The results of the samples heat-treated for different times were compared with the as-deposited sample in terms of morphological, structural properties, and photocatalytic degradation efficiency. It was observed that the ZnO thin films with a heat treatment time of 3 hours had more distinct crystal structures, and their surface morphologies were more regular and homogeneous. When the photocatalytic behaviors were examined, it was determined that the degradation efficiency of the samples heat-treated for 3 hours was better than the other samples. In conclusion, this study shows that the heat treatment time of 1% Fe-doped ZnO thin films deposited by USP significantly affects the films' structural, morphological properties, and photocatalytic activity behaviors. These results emphasize that the heat treatment time of 3 hours should be preferred and guide future research in thin film production and photocatalytic applications.
- 12 October 2025
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 28 (5) , 1535-1543
Open AccessEffects of Heat Treatment Time on Properties of 1% Fe-Doped ZnO Films Fabricated by Ultrasonic Spray Pyrolysis
In this study, 1% Fe-doped ZnO thin films were deposited using Ultrasonic Spray Pyrolysis (USP) to examine their structural, morphological, and photocatalytic properties. Heat treatment was applied to 1% Fe-doped ZnO thin films produced with USP at 500 ºC for different times (1, 3, and 5 hours). The results of the samples heat-treated for different times were compared with the as-deposited sample in terms of morphological, structural properties, and photocatalytic degradation efficiency. It was observed that the ZnO thin films with a heat treatment time of 3 hours had more distinct crystal structures, and their surface morphologies were more regular and homogeneous. When the photocatalytic behaviors were examined, it was determined that the degradation efficiency of the samples heat-treated for 3 hours was better than the other samples. In conclusion, this study shows that the heat treatment time of 1% Fe-doped ZnO thin films deposited by USP significantly affects the films' structural, morphological properties, and photocatalytic activity behaviors. These results emphasize that the heat treatment time of 3 hours should be preferred and guide future research in thin film production and photocatalytic applications.
- Open Access
- 29 June 2024
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 12 (2) , 707-718
AISI 1040 Çeliğinin Mikroyapı Resimlerinden Mekanik Özelliklerinin Derin Öğrenme ile Tahmini
Malzeme biliminde işlem-mikroyapı ve mekanik özellikler arasındaki çok iyi bir ilişki bulunmaktadır. Çeliklerin oda sıcaklığındaki mekanik özellikleri doğrudan mikroyapıda bulunan ferrit, sementit ve perlit hacim oranlarına ve tane boyutlarına bağlıdır. Bu çalışmada, AISI 1040 çeliğinin mikroyapı görüntülerinden yapay zekâ ile oda sıcaklığındaki çekme özelliklerinin tahmini gerçekleştirilmiştir. AISI 1040 çeliğinden ASTM-E8/E8M standardına uygun olarak hazırlanan çekme numuneleri oda sıcaklığında çekme testine tabii tutulmuştur. Sonraki adımda aynı çekme numunelerinin deforme olmamış bölgelerinden metalografik numune hazırlanıp mikroyapı resimleri elde edilmiş, ferrit ve perlit hacim oranları görüntü analizi yazılımıyla hesaplanmıştır. Bu veriler ile özgün bir veri seti oluşturulmuştur. Evrişimsel Sinir Ağı kullanılarak, mikroyapı resimlerinden akma, çekme ve kopma gerilimi değerleri tahmin edilmiştir. Gerçekleştirilen deneyler sonucunda mikroyapı resimlerinden AISI 1040 çeliğinin mekanik özelliklerinin başarılı bir şekilde tahmininin gerçekleştirilebileceği ortaya konulmuştur (MSE=4,36, RMSE=2,08, MAE=1,66, R2=0,99).
- 29 June 2024
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 12 (2) , 707-718
Open AccessAISI 1040 Çeliğinin Mikroyapı Resimlerinden Mekanik Özelliklerinin Derin Öğrenme ile Tahmini
Malzeme biliminde işlem-mikroyapı ve mekanik özellikler arasındaki çok iyi bir ilişki bulunmaktadır. Çeliklerin oda sıcaklığındaki mekanik özellikleri doğrudan mikroyapıda bulunan ferrit, sementit ve perlit hacim oranlarına ve tane boyutlarına bağlıdır. Bu çalışmada, AISI 1040 çeliğinin mikroyapı görüntülerinden yapay zekâ ile oda sıcaklığındaki çekme özelliklerinin tahmini gerçekleştirilmiştir. AISI 1040 çeliğinden ASTM-E8/E8M standardına uygun olarak hazırlanan çekme numuneleri oda sıcaklığında çekme testine tabii tutulmuştur. Sonraki adımda aynı çekme numunelerinin deforme olmamış bölgelerinden metalografik numune hazırlanıp mikroyapı resimleri elde edilmiş, ferrit ve perlit hacim oranları görüntü analizi yazılımıyla hesaplanmıştır. Bu veriler ile özgün bir veri seti oluşturulmuştur. Evrişimsel Sinir Ağı kullanılarak, mikroyapı resimlerinden akma, çekme ve kopma gerilimi değerleri tahmin edilmiştir. Gerçekleştirilen deneyler sonucunda mikroyapı resimlerinden AISI 1040 çeliğinin mekanik özelliklerinin başarılı bir şekilde tahmininin gerçekleştirilebileceği ortaya konulmuştur (MSE=4,36, RMSE=2,08, MAE=1,66, R2=0,99).
- Open Access
- 24 April 2024
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 19 (1) , 544-558
Effect of Two-Step Solution Treatments on the Microstructure and Mechanical Properties of B357 Aluminum Alloy
This study investigates the effect of two-step solution treatments and aging times on the microstructure and mechanical properties of B357 Al–Si alloy, part of the most widely used cast aluminum alloy. Three sets of artificial aging heat treatments were conducted on the tensile samples prepared from B357 alloy produced by low-pressure die casting. Firstly, the conventional artificial aging heat treatment (T6) was carried out by solutionizing the tensile samples at 543 °C for 8.5 h, water quenching at 60 °C, and then artificially aging for 8.5 h at 160 °C. In the two-step solution treatment, the samples were solutionized at 400, 440, 480, and 520 °C for 4 h and then solutionized at 543 °C for 8.5 h and water quenched to 60 °C and then artificially aged for 8.5 h at 160 °C. Thirdly, the samples were solutionized at 480 °C for 4 h, solutionized at 543 °C for 8.5 h, water quenched to 60 °C, and artificially aged for 3–192 h. Despite different solutioning and aging processes, no significant differences were observed in the microstructures of the samples. Si particle coarsening was observed with increasing solution temperature (400–520 °C) and aging times (3–192 h). Si-containing dispersoids and dispersoid-free zones (DFZ) were observed in the primary-α matrix. While DFZ width increased with temperature and aging, dispersoid zones in primary-α dendrites significantly decreased. Differential Scanning Calorimetry (DSC) analysis shows that two-step solution treatment in B357 alloy increases β′ precipitates for Mg2Si precipitation strengthening. The two-step solutionized and aged sample showed the best combination of strength and ductility among all aged samples. B357 alloy exhibited the highest yield and tensile strength (309.7, 366.1 MPa) with 6% elongation for two-step solutionizing and 48 h aging. All aged B357 alloys showed ductile fracture as the primary fracture mode. However, brittle fractured Si particles were observed on the fracture surfaces.
- 24 April 2024
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 19 (1) , 544-558
Open AccessEffect of Two-Step Solution Treatments on the Microstructure and Mechanical Properties of B357 Aluminum Alloy
This study investigates the effect of two-step solution treatments and aging times on the microstructure and mechanical properties of B357 Al–Si alloy, part of the most widely used cast aluminum alloy. Three sets of artificial aging heat treatments were conducted on the tensile samples prepared from B357 alloy produced by low-pressure die casting. Firstly, the conventional artificial aging heat treatment (T6) was carried out by solutionizing the tensile samples at 543 °C for 8.5 h, water quenching at 60 °C, and then artificially aging for 8.5 h at 160 °C. In the two-step solution treatment, the samples were solutionized at 400, 440, 480, and 520 °C for 4 h and then solutionized at 543 °C for 8.5 h and water quenched to 60 °C and then artificially aged for 8.5 h at 160 °C. Thirdly, the samples were solutionized at 480 °C for 4 h, solutionized at 543 °C for 8.5 h, water quenched to 60 °C, and artificially aged for 3–192 h. Despite different solutioning and aging processes, no significant differences were observed in the microstructures of the samples. Si particle coarsening was observed with increasing solution temperature (400–520 °C) and aging times (3–192 h). Si-containing dispersoids and dispersoid-free zones (DFZ) were observed in the primary-α matrix. While DFZ width increased with temperature and aging, dispersoid zones in primary-α dendrites significantly decreased. Differential Scanning Calorimetry (DSC) analysis shows that two-step solution treatment in B357 alloy increases β′ precipitates for Mg2Si precipitation strengthening. The two-step solutionized and aged sample showed the best combination of strength and ductility among all aged samples. B357 alloy exhibited the highest yield and tensile strength (309.7, 366.1 MPa) with 6% elongation for two-step solutionizing and 48 h aging. All aged B357 alloys showed ductile fracture as the primary fracture mode. However, brittle fractured Si particles were observed on the fracture surfaces.
- 26 June 2023
- Published by ASME International in Journal of Tribology
- Vol. 145 (10) , 1-7
Tribological Characteristics of Tantalum-Oxide Coating Fabricated on Pre-Treated 2024 Aluminum Alloys
Aluminum has many advantages, such as being lightweight, but it may not provide sufficient wear resistance for some applications. Tantalum oxide is a ceramic-based coating layer that can improve wear resistance. In this study, 2024 aluminum alloy samples with different surface treatments were coated with amorphous Ta2O5 using the RF spraying method under the same conditions. Polishing, 10% HCl solution, 5% NaOH solution, and 50% HNO3 solution, as well as sandblasting, were applied to the surfaces of aluminum alloys separately, and the sample groups were coated. The effects of pre-coating surface treatments on coating morphology and wear resistance were investigated. The surface morphologies of the coatings were examined using scanning electron microscopy, electron dispersion spectroscopy, and X-ray diffraction. Wear tests were then conducted to determine the mechanical properties, and after the tests, scanning electron microscopy examinations and volume loss calculations were performed using a profilometer. The wear test results were discussed and compared. The investigation yielded continuous, homogeneous, and crack-free coatings on the 2024 aluminum alloy surfaces. However, the wear resistance of these coatings was compromised by acid etching. Following polishing and sandblasting, the coated surfaces experienced a decrease in volume losses from abrasion by 4.3% and 44.8%, respectively, compared to the uncoated samples.
- 26 June 2023
- Published by ASME International in Journal of Tribology
- Vol. 145 (10) , 1-7
Tribological Characteristics of Tantalum-Oxide Coating Fabricated on Pre-Treated 2024 Aluminum Alloys
Aluminum has many advantages, such as being lightweight, but it may not provide sufficient wear resistance for some applications. Tantalum oxide is a ceramic-based coating layer that can improve wear resistance. In this study, 2024 aluminum alloy samples with different surface treatments were coated with amorphous Ta2O5 using the RF spraying method under the same conditions. Polishing, 10% HCl solution, 5% NaOH solution, and 50% HNO3 solution, as well as sandblasting, were applied to the surfaces of aluminum alloys separately, and the sample groups were coated. The effects of pre-coating surface treatments on coating morphology and wear resistance were investigated. The surface morphologies of the coatings were examined using scanning electron microscopy, electron dispersion spectroscopy, and X-ray diffraction. Wear tests were then conducted to determine the mechanical properties, and after the tests, scanning electron microscopy examinations and volume loss calculations were performed using a profilometer. The wear test results were discussed and compared. The investigation yielded continuous, homogeneous, and crack-free coatings on the 2024 aluminum alloy surfaces. However, the wear resistance of these coatings was compromised by acid etching. Following polishing and sandblasting, the coated surfaces experienced a decrease in volume losses from abrasion by 4.3% and 44.8%, respectively, compared to the uncoated samples.
- Open Access
- 25 January 2023
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 17 (2) , 1439
Correction: Effects of Short-Time Austenitization on Mechanical Properties and Transformation-Induced Plasticity in Alloyed Austempered Ductile Iron
- 25 January 2023
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 17 (2) , 1439
Open AccessCorrection: Effects of Short-Time Austenitization on Mechanical Properties and Transformation-Induced Plasticity in Alloyed Austempered Ductile Iron
- 1 September 2022
- Published by Konya Muhendislik Bilimleri Dergisi in Konya Journal of Engineering Sciences
- Vol. 10 (3) , 692-703
NORMALİZE ISIL İŞLEMİNDE ARAKRİTİK ÖSTENİTLEME SICAKLIĞININ KÜRESEL GRAFİTLİ DÖKME DEMİRİN MİKROYAPI VE MEKANİK ÖZELLİKLERİ ÜZERİNE ETKİSİ
Bu araştırmada, arakritik östenitleme sıcaklıklarında tavlama sonrası, normalize ısıl işlemlerinin alaşımsız küresel grafitli dökme demirin (KGDD) mikroyapısal değişimine ve mekanik özelliklerine etkisi incelenmiştir. Y blok olarak dökülen alaşımsız KGDD’den çekme numuneleri tornalamayla hazırlanmıştır. Çekme numuneleri farklı arakritik östenitleme sıcaklıklarında (770°C ila 820°C) 60 dk östenitleme sonrası havada soğutulmuştur. Optik mikroskop ve tarama elektron mikroskobuyla (SEM) mikroyapılar karakterize edilmiştir. Çekme ve sertlik testleriyle mekanik özellikler belirlenmiştir. Belirli bir kimyasal bileşimdeki KGDD’de arakritik östenitleme sıcaklıklarından normalize ısıl işlemiyle, % 8 ila % 75 perlit hacim oranlarında KGDD üretilebilmektedir. Arakritik östenitleme sıcaklığının artışıyla perlit hacim oranının belirgin bir şekilde arttığı belirlenmiştir. Ayrıca perlit hacim oranının artışıyla sertlik, akma ve çekme dayanımında belirgin artış tespit edilmiştir. Buna karşın toplam uzama ve kesit alanı daralmasının azalan ötektoid öncesi ferrit hacim oranıyla azaldığı belirlenmiştir. Perlit hacim oranının % 8’den % 75 artmasıyla; sertlik 181 BHN’den 259 BHN’ye; akma dayanımı 348 MPa’dan 470 MPa’ya; çekme dayanımı 569 MPa’dan 790 MPa’ya belirgin bir şekilde artarken toplam % uzama % 12,6’dan % 8,3’e azalmaktadır. Artan perlit hacim oranıyla kırık yüzeylerdeki çukurcukların azaldığı gözlenmiştir.
- 1 September 2022
- Published by Konya Muhendislik Bilimleri Dergisi in Konya Journal of Engineering Sciences
- Vol. 10 (3) , 692-703
NORMALİZE ISIL İŞLEMİNDE ARAKRİTİK ÖSTENİTLEME SICAKLIĞININ KÜRESEL GRAFİTLİ DÖKME DEMİRİN MİKROYAPI VE MEKANİK ÖZELLİKLERİ ÜZERİNE ETKİSİ
Bu araştırmada, arakritik östenitleme sıcaklıklarında tavlama sonrası, normalize ısıl işlemlerinin alaşımsız küresel grafitli dökme demirin (KGDD) mikroyapısal değişimine ve mekanik özelliklerine etkisi incelenmiştir. Y blok olarak dökülen alaşımsız KGDD’den çekme numuneleri tornalamayla hazırlanmıştır. Çekme numuneleri farklı arakritik östenitleme sıcaklıklarında (770°C ila 820°C) 60 dk östenitleme sonrası havada soğutulmuştur. Optik mikroskop ve tarama elektron mikroskobuyla (SEM) mikroyapılar karakterize edilmiştir. Çekme ve sertlik testleriyle mekanik özellikler belirlenmiştir. Belirli bir kimyasal bileşimdeki KGDD’de arakritik östenitleme sıcaklıklarından normalize ısıl işlemiyle, % 8 ila % 75 perlit hacim oranlarında KGDD üretilebilmektedir. Arakritik östenitleme sıcaklığının artışıyla perlit hacim oranının belirgin bir şekilde arttığı belirlenmiştir. Ayrıca perlit hacim oranının artışıyla sertlik, akma ve çekme dayanımında belirgin artış tespit edilmiştir. Buna karşın toplam uzama ve kesit alanı daralmasının azalan ötektoid öncesi ferrit hacim oranıyla azaldığı belirlenmiştir. Perlit hacim oranının % 8’den % 75 artmasıyla; sertlik 181 BHN’den 259 BHN’ye; akma dayanımı 348 MPa’dan 470 MPa’ya; çekme dayanımı 569 MPa’dan 790 MPa’ya belirgin bir şekilde artarken toplam % uzama % 12,6’dan % 8,3’e azalmaktadır. Artan perlit hacim oranıyla kırık yüzeylerdeki çukurcukların azaldığı gözlenmiştir.
- 30 June 2022
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 10 (2) , 164-176
Effect of Nitriding Process on Wear Behavior of Dual Phase (Ferrite+Martensite) Ductile Cast Iron
In this study, it was aimed to improve the surface hardness by applying gas nitriding treatment to dual-phase ductile cast iron and to produce ductile cast irons with a good strength-ductility combination. Thus, it has been tried to develop a ductile cast iron with high wear resistance, strength, and ductility. Ductile cast iron specimens with a dual-phase microstructure consisting of ferrite + martensite were produced by oil quenching at 70 °C after intercritical austenitizing at 800 ⁰C in the ferrite + austenite zone. Instead of the tempering process, nitriding treatment was applied to the dual-phase ductile cast iron specimens at 560 °C for 540 minutes. The tempering process required to be applied to the martensitic structure was also performed by the nitriding process and a hard 10 µm thick nitride layer was obtained on the surface. Optical microscope and XRD analysis were performed for microstructural characterization of nitrided dual-phase ductile cast iron specimens. The wear properties were tested with a tribometer. For comparison reasons, microstructural characterization and wear tests were also performed on non-nitrided dual-phase ductile cast iron. In ductile cast iron, microstructures consist of a hard nitride layer (10 µm white layer) on the surface and a ferrite + tempered martensite (43% martensite volume fraction) structure in the center can be produced by oil quenching from intercritical austenitizing and nitriding treatment. Surface hardness of 510 HV in nitrided dual-phase ductile cast iron, 193 HV in dual-phase ductile cast iron, and 353 HV in austempered KGDD were obtained. The lowest weight loss and coefficient of friction were obtained in nitrided dual-phase ductile cast iron. The highest weight loss and friction coefficient values with wear were obtained in dual-phase ductile cast iron. The wear resistance of nitrided dual-phase ductile cast iron is 2 times higher than that of dual-phase ductile cast iron and austempered ductile cast iron.
- 30 June 2022
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 10 (2) , 164-176
Effect of Nitriding Process on Wear Behavior of Dual Phase (Ferrite+Martensite) Ductile Cast Iron
In this study, it was aimed to improve the surface hardness by applying gas nitriding treatment to dual-phase ductile cast iron and to produce ductile cast irons with a good strength-ductility combination. Thus, it has been tried to develop a ductile cast iron with high wear resistance, strength, and ductility. Ductile cast iron specimens with a dual-phase microstructure consisting of ferrite + martensite were produced by oil quenching at 70 °C after intercritical austenitizing at 800 ⁰C in the ferrite + austenite zone. Instead of the tempering process, nitriding treatment was applied to the dual-phase ductile cast iron specimens at 560 °C for 540 minutes. The tempering process required to be applied to the martensitic structure was also performed by the nitriding process and a hard 10 µm thick nitride layer was obtained on the surface. Optical microscope and XRD analysis were performed for microstructural characterization of nitrided dual-phase ductile cast iron specimens. The wear properties were tested with a tribometer. For comparison reasons, microstructural characterization and wear tests were also performed on non-nitrided dual-phase ductile cast iron. In ductile cast iron, microstructures consist of a hard nitride layer (10 µm white layer) on the surface and a ferrite + tempered martensite (43% martensite volume fraction) structure in the center can be produced by oil quenching from intercritical austenitizing and nitriding treatment. Surface hardness of 510 HV in nitrided dual-phase ductile cast iron, 193 HV in dual-phase ductile cast iron, and 353 HV in austempered KGDD were obtained. The lowest weight loss and coefficient of friction were obtained in nitrided dual-phase ductile cast iron. The highest weight loss and friction coefficient values with wear were obtained in dual-phase ductile cast iron. The wear resistance of nitrided dual-phase ductile cast iron is 2 times higher than that of dual-phase ductile cast iron and austempered ductile cast iron.