Štěpánka Kelarová
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Štěpánka Kelarová has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Roman Přibyl
R&D Center for Plasma and Nanotechnology Surface Modifications, CEPLANT, Brno, Czech Republic
6 shared publications - Vilma Buršíková
Department of Plasma Physics and Technology, Faculty of Science, Masaryk University, Kotlářská 2, 611 37 Brno, Czech Republic
4 shared publications Richard Václavik
3 shared publicationsVojtěch Homola
3 shared publications- Anna Charvátová Campbell
Czech Metrology Institute
2 shared publications - Lukáš Zábranský
Department of Physical Electronics, Faculty of Science, Masaryk University, Kotlárská 2, 61137 Brno, Czech Republic
2 shared publications
Latest Publications
- Open Access
- 24 August 2026
- Published by Elsevier in SSRN Electronic Journal
Comparative Study of a‑C:H:SiOx Coatings Based on TMSAc and HMDSO Precursors Prepared by PECVD
The main aim of the present study was to prepare a-C:H:SiOx coatings with sufficient mechanical properties from the mixture of CH4 with trimethylsilyl acetate (TMSAc) or hexamethyldisiloxane (HMDSO) organosilicon precursor using plasmas of RF capacitively coupled glow discharge.Studied coatings were prepared using various precursor ratios in the reaction mixtures, ranging from 7.1 % to 92.9 %, at a constant discharge power of 75 W. The included research work discusses in detail the evolution of the chemical composition, structure, and mechanical characteristics of the resulting a-C:H:SiOx coatings as a function of the precursor ratio and precursor type. Particular emphasis is placed on elucidating the transition from hard SiOx-doped carbon films to soft organosilicon matrices and on understanding how this transition affects the film properties.In this study, various materials with a smooth surface structure with a root mean square roughness below 0.3 nm were produced. Gradual increase in the precursor ratio induced significant structural changes, resulting in the transition from a-C:H:SiOx coatings with a remarkable hardness of ∼11 GPa to soft polymer-like matrices reaching hardness below 1 GPa. Hard a-C:H:SiOx coatings with excellent fracture resistance exhibiting a low friction coefficient in the range 0.08±0.01 can be achieved using both organosilicon compounds and precursor ratios 7.1-14.3 %. Under these conditions, HMDSO may be replaced with TMSAc to produce hard a-C:H:SiOx coatings with comparable mechanical properties.
- 24 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessComparative Study of a‑C:H:SiOx Coatings Based on TMSAc and HMDSO Precursors Prepared by PECVD
The main aim of the present study was to prepare a-C:H:SiOx coatings with sufficient mechanical properties from the mixture of CH4 with trimethylsilyl acetate (TMSAc) or hexamethyldisiloxane (HMDSO) organosilicon precursor using plasmas of RF capacitively coupled glow discharge.Studied coatings were prepared using various precursor ratios in the reaction mixtures, ranging from 7.1 % to 92.9 %, at a constant discharge power of 75 W. The included research work discusses in detail the evolution of the chemical composition, structure, and mechanical characteristics of the resulting a-C:H:SiOx coatings as a function of the precursor ratio and precursor type. Particular emphasis is placed on elucidating the transition from hard SiOx-doped carbon films to soft organosilicon matrices and on understanding how this transition affects the film properties.In this study, various materials with a smooth surface structure with a root mean square roughness below 0.3 nm were produced. Gradual increase in the precursor ratio induced significant structural changes, resulting in the transition from a-C:H:SiOx coatings with a remarkable hardness of ∼11 GPa to soft polymer-like matrices reaching hardness below 1 GPa. Hard a-C:H:SiOx coatings with excellent fracture resistance exhibiting a low friction coefficient in the range 0.08±0.01 can be achieved using both organosilicon compounds and precursor ratios 7.1-14.3 %. Under these conditions, HMDSO may be replaced with TMSAc to produce hard a-C:H:SiOx coatings with comparable mechanical properties.
- Open Access
- 20 April 2026
- Published by Elsevier in SSRN Electronic Journal
Comparative study of a-C:H:SiOx coatings based on TMSAc and HMDSO precursors prepared by PECVD
The main aim of the present study was to prepare a-C:H:SiOx coatings with sufficient mechanical properties from the mixture of CH4 with trimethylsilyl acetate (TMSAc) or hexamethyldisiloxane (HMDSO) organosilicon precursor using plasmas of RF capacitively coupled glow discharge. Studied coatings were prepared using various precursor ratios in the reaction mixtures, ranging from 7.1% to 92.9%, at a constant discharge power of 75 W. The included research work discusses in detail the evolution of the chemical composition and mechanical characteristics of the resulting a-C:H:SiOx films as a function of the variable precursor ratio and the type of precursor. In this study, various materials with a smooth surface structure were produced. Gradual increase in the precursor ratio induced significant structural changes, resulting in the transition from a-C:H:SiOx coatings with a remarkable hardness of ∼11 GPa to soft polymer-like matrices reaching hardness below 1 GPa. This research work also describes in detail the differences between TMSAc- and HMDSO-based materials.Hard a-C:H:SiOx coatings with excellent fracture resistance exhibiting a low friction coefficient in the range 0.08±0.01 can be achieved using both precursors. Under certain conditions, HMDSO may be replaced by a less toxic TMSAc to prepare materials exhibiting comparable mechanical properties.
- 20 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessComparative study of a-C:H:SiOx coatings based on TMSAc and HMDSO precursors prepared by PECVD
The main aim of the present study was to prepare a-C:H:SiOx coatings with sufficient mechanical properties from the mixture of CH4 with trimethylsilyl acetate (TMSAc) or hexamethyldisiloxane (HMDSO) organosilicon precursor using plasmas of RF capacitively coupled glow discharge. Studied coatings were prepared using various precursor ratios in the reaction mixtures, ranging from 7.1% to 92.9%, at a constant discharge power of 75 W. The included research work discusses in detail the evolution of the chemical composition and mechanical characteristics of the resulting a-C:H:SiOx films as a function of the variable precursor ratio and the type of precursor. In this study, various materials with a smooth surface structure were produced. Gradual increase in the precursor ratio induced significant structural changes, resulting in the transition from a-C:H:SiOx coatings with a remarkable hardness of ∼11 GPa to soft polymer-like matrices reaching hardness below 1 GPa. This research work also describes in detail the differences between TMSAc- and HMDSO-based materials.Hard a-C:H:SiOx coatings with excellent fracture resistance exhibiting a low friction coefficient in the range 0.08±0.01 can be achieved using both precursors. Under certain conditions, HMDSO may be replaced by a less toxic TMSAc to prepare materials exhibiting comparable mechanical properties.
- 7 August 2025
- Published by Elsevier in Surfaces and Interfaces
- Vol. 74
Degradation of mechanical properties of nitrogen-doped organosilicon plasma polymers induced by post-deposition reactions
- 7 August 2025
- Published by Elsevier in Surfaces and Interfaces
- Vol. 74
Degradation of mechanical properties of nitrogen-doped organosilicon plasma polymers induced by post-deposition reactions
- Open Access
- 28 October 2024
- Published by Elsevier in Carbon Trends
- Vol. 17
Deposition of nanocomposite carbon-based thin films doped with copper and fluorine
- 28 October 2024
- Published by Elsevier in Carbon Trends
- Vol. 17
Open AccessDeposition of nanocomposite carbon-based thin films doped with copper and fluorine
- 1 August 2021
- Published by Elsevier in Polymer Degradation and Stability
- Vol. 190
Stability of trimethylsilyl acetate-based plasma polymers towards atmospheric and water environments
- 1 August 2021
- Published by Elsevier in Polymer Degradation and Stability
- Vol. 190
Stability of trimethylsilyl acetate-based plasma polymers towards atmospheric and water environments
- Open Access
- 1 January 2020
- Published by TANGER Ltd.
- Vol. 2020, 535-540
Organosilicon plasma polymers deposited in trimethylsilyl acetate/CH4 plasma of capacitively coupled RF glow discharge
- 1 January 2020
- Published by TANGER Ltd.
- Vol. 2020, 535-540
Open AccessOrganosilicon plasma polymers deposited in trimethylsilyl acetate/CH4 plasma of capacitively coupled RF glow discharge