Savita Kashyap
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Savita Kashyap has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Jaya Madan
Centre for Research Impact and Outcome, Chitkara University Institute of Engineering and Technology, Chitkara University, Rajpura, India
7 shared publications - Rahul Pandey
Department of Applied Sciences (Physics), National Institute of Technology Delhi, New Delhi, India
7 shared publications - Pradeep Padhamnath
Faculty of Metals Engineering and Industrial Computer Science, AGH University of Kraków, al. Adama Mickiewicza 30, 30-059 Kraków, Poland
2 shared publications - Rajnish Sharma
School of Engineering and Technology, Chitkara University, Solan, India
2 shared publications - Abdelmoumene Laidouci
Faculty of Sciences, University of Blida 1, Blida, Algeria
1 shared publication Anil Kottantharayil
National Centre for Photovoltaic Research and Education
1 shared publication
Latest Publications
- Open Access
- 14 January 2026
- Published by TIB Open Publishing in SiliconPV Conference Proceedings
- Vol. 3
Numerical Analysis of Metal Poly-Si Contact in TOPCon Solar Cells Through Device Simulations Using Sentaurus TCAD
Tunnel oxide passivated contact (TOPCon) is an emerging technology for highly efficient with excellent passivation photovoltaic (PV) devices. However, a standard TOPCon cell suffers from insufficient efficiency gain and recombination losses due to the presence of a direct metal-crystalline silicon contact. Therefore, bifacial configurations with advanced passivated structures have been considered in this research work. In this work, the performance of bifacial TOPCon device with double-side (DS) TOPCon structures, integrated with poly-Si, is explored and modeled using Sentaurus TCAD software. The reported study develops a framework to obtain state-of-the-art bifacial TOPCon structures with optimized input parameters and considering tunneling structures. The impact of collective front/rear SiNx layer thickness (from 50 to 100 nm) and p+ poly Si thickness (from 20 to 100 nm) on the performance of bifacial-DS TOPCon solar is studied and analyzed for optimized PV performance. This research study reveals that optimizing the p+ poly-Si thickness enhances carrier collection with minimal bulk recombination losses. The PV performance of DS structure indicates that incorporating DS carrier selective contacts increases the PV efficiency. Also, the detailed analysis of bifacial TOPCon structure reveals that suppressing the recombination by incorporating tunneling structures on both sides can be the key strategy to improve PV performance with an optimized efficiency of 26.3%. The reported study set a clear direction for higher PV performance by incorporating a tunneling approach in next-generation c-Si solar cells at low cost.
- 14 January 2026
- Published by TIB Open Publishing in SiliconPV Conference Proceedings
- Vol. 3
Open AccessNumerical Analysis of Metal Poly-Si Contact in TOPCon Solar Cells Through Device Simulations Using Sentaurus TCAD
Tunnel oxide passivated contact (TOPCon) is an emerging technology for highly efficient with excellent passivation photovoltaic (PV) devices. However, a standard TOPCon cell suffers from insufficient efficiency gain and recombination losses due to the presence of a direct metal-crystalline silicon contact. Therefore, bifacial configurations with advanced passivated structures have been considered in this research work. In this work, the performance of bifacial TOPCon device with double-side (DS) TOPCon structures, integrated with poly-Si, is explored and modeled using Sentaurus TCAD software. The reported study develops a framework to obtain state-of-the-art bifacial TOPCon structures with optimized input parameters and considering tunneling structures. The impact of collective front/rear SiNx layer thickness (from 50 to 100 nm) and p+ poly Si thickness (from 20 to 100 nm) on the performance of bifacial-DS TOPCon solar is studied and analyzed for optimized PV performance. This research study reveals that optimizing the p+ poly-Si thickness enhances carrier collection with minimal bulk recombination losses. The PV performance of DS structure indicates that incorporating DS carrier selective contacts increases the PV efficiency. Also, the detailed analysis of bifacial TOPCon structure reveals that suppressing the recombination by incorporating tunneling structures on both sides can be the key strategy to improve PV performance with an optimized efficiency of 26.3%. The reported study set a clear direction for higher PV performance by incorporating a tunneling approach in next-generation c-Si solar cells at low cost.
- 6 January 2026
- Published by Elsevier in Solar Energy
- Vol. 306
Optimizing the Performance of Multi-Structure TOPCon Solar Cells: A Numerical Analysis using Sentaurus-TCAD
- 6 January 2026
- Published by Elsevier in Solar Energy
- Vol. 306
Optimizing the Performance of Multi-Structure TOPCon Solar Cells: A Numerical Analysis using Sentaurus-TCAD
- 8 November 2023
- Published by IOP Publishing in Physica Scripta
- Vol. 98 (12) , 125509
Performance enhancement of CsPbI3-xBrx perovskite solar cells via graded bandgap and affinity engineering
All inorganic cesium lead-based perovskite solar cells (PSCs) have gained attention as alternative absorbing materials owing to their exceptional thermal stability. However, these devices are suffer from transmission and thermalization losses. Therefore, a novel grading approach is used in CsPbI3-x Brx perovskite solar cell to reduce the transmission and thermalization losses by enhancing the cell’s ability to capture a broad spectrum of light wavelengths and suitably accommodate the material’s energy bandgap. In this work, the performance of CsPbI3-xBrx perovskite solar cell with graded bandgap (Eg) and affinity has been explored and analyzed using the simulation SCAPS-1D tool. Different compositions (x) are varied to adjust the bandgap of CsPbI3-xBrx with different grading profiles such as linear, parabolic and beta grading. The graded structure enhances the absorption wavelength range and carrier lifetime. However, it also leads to the redistribution of the electrical field within the device, promoting more effective charge separation and collection. By utilizing this approach, the impact of absorber thickness variations from (50 nm to 700 nm) is also studied and analyzed with respect to grading profiles. Initially, 16.75% power conversion efficiency (PCE) is obtained by calibrating the experimental CsPbI3-xBrx graded solar cell. Then, performance is further improved by adjusting the bandgap with grading profiles, optimizing ETLs/HTLs and achieving optimum PV parameters: short-circuit current density (JSC) of 20.50 mA cm−2, open-circuit voltage (VOC) of 1.35 V, fill factor (FF) of 84.15% and PCE of 23.11%. The findings of the reported study would significantly provide a path for the development of graded PSC.
- 8 November 2023
- Published by IOP Publishing in Physica Scripta
- Vol. 98 (12) , 125509
Performance enhancement of CsPbI3-xBrx perovskite solar cells via graded bandgap and affinity engineering
All inorganic cesium lead-based perovskite solar cells (PSCs) have gained attention as alternative absorbing materials owing to their exceptional thermal stability. However, these devices are suffer from transmission and thermalization losses. Therefore, a novel grading approach is used in CsPbI3-x Brx perovskite solar cell to reduce the transmission and thermalization losses by enhancing the cell’s ability to capture a broad spectrum of light wavelengths and suitably accommodate the material’s energy bandgap. In this work, the performance of CsPbI3-xBrx perovskite solar cell with graded bandgap (Eg) and affinity has been explored and analyzed using the simulation SCAPS-1D tool. Different compositions (x) are varied to adjust the bandgap of CsPbI3-xBrx with different grading profiles such as linear, parabolic and beta grading. The graded structure enhances the absorption wavelength range and carrier lifetime. However, it also leads to the redistribution of the electrical field within the device, promoting more effective charge separation and collection. By utilizing this approach, the impact of absorber thickness variations from (50 nm to 700 nm) is also studied and analyzed with respect to grading profiles. Initially, 16.75% power conversion efficiency (PCE) is obtained by calibrating the experimental CsPbI3-xBrx graded solar cell. Then, performance is further improved by adjusting the bandgap with grading profiles, optimizing ETLs/HTLs and achieving optimum PV parameters: short-circuit current density (JSC) of 20.50 mA cm−2, open-circuit voltage (VOC) of 1.35 V, fill factor (FF) of 84.15% and PCE of 23.11%. The findings of the reported study would significantly provide a path for the development of graded PSC.
- 27 October 2023
- Published by Elsevier in Micro and Nanostructures
- Vol. 184
Investigating the potential of earth-abundant ZnSnxGe1-xN2 alloys for quantum well solar cells
- 27 October 2023
- Published by Elsevier in Micro and Nanostructures
- Vol. 184
Investigating the potential of earth-abundant ZnSnxGe1-xN2 alloys for quantum well solar cells
- 11 October 2023
- Published by IOP Publishing in Physica Scripta
- Vol. 98 (11) , 114001
Simulated bending test analysis of 23% efficient lead-free flexible perovskite solar cell with different bending states
Perovskite solar cells (PSCs) have emerged as a promising technology for developing highly efficient and low-cost photovoltaic (PV) devices. However, toxicity is the primary limiting factor that is restraining the use of traditional PSCs. Therefore, lead-free PSCs have been considered the best alternative due to lead toxicity and environmental impact. The secondary obstacle hindering the potential of PSCs for wearable applications is their limited flexibility. Therefore, lead-free flexible PSC (F-PSC) device is designed and simulated through the Silvaco-TCAD tool in this work. Despite the significant advancements made in F-PSCs, insufficient research is conducted to examine their performance under different bending states to study the reliability of the device’s flexibility. Here, three different bending states have been reported to investigate the proposed device performance, viz. convex, concave, and sinusoidal. The impact of bending radius (BR) in convex and concave from 5 to 20 mm and bending amplitude (BA) in the sinusoidal state from 0.5 to 2 mm is studied and analyzed to optimize the device performance. The performance of the proposed lead-free F-PSC is explored in terms of the current density (JV) curve, PV parameters, and external quantum efficiency (EQE). Optimized PV parameters of the proposed F-PSC are: short-circuit current density (J SC ) of 33.45 mA cm −2 , open-circuit voltage (V OC ) of 0.925 V, fill factor (FF) of 77.15% and PCE of 23.87%. The findings of the reported study would significantly provide a path for the development of F-PSC.
- 11 October 2023
- Published by IOP Publishing in Physica Scripta
- Vol. 98 (11) , 114001
Simulated bending test analysis of 23% efficient lead-free flexible perovskite solar cell with different bending states
Perovskite solar cells (PSCs) have emerged as a promising technology for developing highly efficient and low-cost photovoltaic (PV) devices. However, toxicity is the primary limiting factor that is restraining the use of traditional PSCs. Therefore, lead-free PSCs have been considered the best alternative due to lead toxicity and environmental impact. The secondary obstacle hindering the potential of PSCs for wearable applications is their limited flexibility. Therefore, lead-free flexible PSC (F-PSC) device is designed and simulated through the Silvaco-TCAD tool in this work. Despite the significant advancements made in F-PSCs, insufficient research is conducted to examine their performance under different bending states to study the reliability of the device’s flexibility. Here, three different bending states have been reported to investigate the proposed device performance, viz. convex, concave, and sinusoidal. The impact of bending radius (BR) in convex and concave from 5 to 20 mm and bending amplitude (BA) in the sinusoidal state from 0.5 to 2 mm is studied and analyzed to optimize the device performance. The performance of the proposed lead-free F-PSC is explored in terms of the current density (JV) curve, PV parameters, and external quantum efficiency (EQE). Optimized PV parameters of the proposed F-PSC are: short-circuit current density (J SC ) of 33.45 mA cm −2 , open-circuit voltage (V OC ) of 0.925 V, fill factor (FF) of 77.15% and PCE of 23.87%. The findings of the reported study would significantly provide a path for the development of F-PSC.
- 5 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 23 (3) , 380-385
Reliability Test of 21% Efficient Flexible Perovskite Solar Cell Under Concave, Convex and Sinusoidal Bending
Perovskite solar cells (PSCs) have been considered the new rising star in photovoltaic (PV) technology. However, flexibility is the major limiting factor in PSCs for restraining the potential for wearable applications. Therefore, the flexible-PSC (F-PSC) design is reported and simulated using the Silvaco-TCAD tool. Different bending modes, such as concave, convex, and sinusoidal, including planar structure, have been reported to examine the performance of the proposed device. The influence of bending radius (5 to 20 mm) and bending amplitude (0.5 to 2 mm) is studied and analyzed to optimize the performance of the F-PSC device. It has been obtained that the planar F-PSC delivers higher PV parameters: short-circuit current density (JSC) of 21.9 mA/cm, open-circuit voltage (VOC) of 1.18 V, fill factor (FF) of 79.31% and PCE of 20.5%. Simulated results are obtained regarding PV parameters, JV, and EQE characteristics. The findings of the reported study would significantly provide a way to explore the F-PSC performance with better-bending properties.
- 5 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 23 (3) , 380-385
Reliability Test of 21% Efficient Flexible Perovskite Solar Cell Under Concave, Convex and Sinusoidal Bending
Perovskite solar cells (PSCs) have been considered the new rising star in photovoltaic (PV) technology. However, flexibility is the major limiting factor in PSCs for restraining the potential for wearable applications. Therefore, the flexible-PSC (F-PSC) design is reported and simulated using the Silvaco-TCAD tool. Different bending modes, such as concave, convex, and sinusoidal, including planar structure, have been reported to examine the performance of the proposed device. The influence of bending radius (5 to 20 mm) and bending amplitude (0.5 to 2 mm) is studied and analyzed to optimize the performance of the F-PSC device. It has been obtained that the planar F-PSC delivers higher PV parameters: short-circuit current density (JSC) of 21.9 mA/cm, open-circuit voltage (VOC) of 1.18 V, fill factor (FF) of 79.31% and PCE of 20.5%. Simulated results are obtained regarding PV parameters, JV, and EQE characteristics. The findings of the reported study would significantly provide a way to explore the F-PSC performance with better-bending properties.
- 24 March 2023
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 38 (5) , 055010
25.7% efficient PERC solar cell using double side silicide on oxide electrostatically doped (SILO-ED) carrier selective contacts: process and device simulation study
Passivating contacts have recently considered as a superior carrier-selective contact approach for high-efficiency silicon-based photovoltaic devices. However, the conversion efficiencies of the silicon-based passivated emitter and rear cell (PERC) are limited by contact recombination losses that reduce their performance. Therefore, we investigated a new manufacturable silicide on oxide-based electrostatically doped (SILO-ED) carrier-selective contact to suppress the contact recombination losses and reduce the saturation current density (j 0). For the first time, double side electrostatic doping is introduced to the PERC devices to form the carrier selective passivating contacts. First, a conventional PERC device was designed and the effects of surface recombination velocity (SRV) at both contacts were studied. After that, single and double SILO-ED based contacts are introduced into the device and a systematic analysis is performed to understand the tunneling phenomena and improve the conversion efficiency compared to existing PERC cells. The front SILO-ED based device with back contact SRV of 10 cm s−1 showed a power conversion efficiency of 25.4% with j 0 (14.3 fA·cm−2). In contrast, the double SILO-ED device delivered 25.7% conversion efficiency by further suppressing the j 0 to 11.8 fA·cm−2 by implementing SILO-ED approach with two different metal silicides such as erbium silicide (ErSi2) and palladium silicide (Pd2Si) on front and rear contact surface. The champion double SILO-ED PERC solar cell delivered a conversion efficiency of 25.7% with an open circuit voltage (V OC) of 742 mV. The results reported in this study would help to develop superior passivating contact-based PERC solar cells for higher efficiencies.
- 24 March 2023
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 38 (5) , 055010
25.7% efficient PERC solar cell using double side silicide on oxide electrostatically doped (SILO-ED) carrier selective contacts: process and device simulation study
Passivating contacts have recently considered as a superior carrier-selective contact approach for high-efficiency silicon-based photovoltaic devices. However, the conversion efficiencies of the silicon-based passivated emitter and rear cell (PERC) are limited by contact recombination losses that reduce their performance. Therefore, we investigated a new manufacturable silicide on oxide-based electrostatically doped (SILO-ED) carrier-selective contact to suppress the contact recombination losses and reduce the saturation current density (j 0). For the first time, double side electrostatic doping is introduced to the PERC devices to form the carrier selective passivating contacts. First, a conventional PERC device was designed and the effects of surface recombination velocity (SRV) at both contacts were studied. After that, single and double SILO-ED based contacts are introduced into the device and a systematic analysis is performed to understand the tunneling phenomena and improve the conversion efficiency compared to existing PERC cells. The front SILO-ED based device with back contact SRV of 10 cm s−1 showed a power conversion efficiency of 25.4% with j 0 (14.3 fA·cm−2). In contrast, the double SILO-ED device delivered 25.7% conversion efficiency by further suppressing the j 0 to 11.8 fA·cm−2 by implementing SILO-ED approach with two different metal silicides such as erbium silicide (ErSi2) and palladium silicide (Pd2Si) on front and rear contact surface. The champion double SILO-ED PERC solar cell delivered a conversion efficiency of 25.7% with an open circuit voltage (V OC) of 742 mV. The results reported in this study would help to develop superior passivating contact-based PERC solar cells for higher efficiencies.
- 24 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Numerical Simulations of FASnI3 based Solar Cell with the Variation of Absorber Layer Thickness
Tin based solar cells are considered as a promising contender in the photovoltaic (PV) industry. However, the performance of PV devices based on Formamidinium tin iodide (FASnI 3 ) material is still lagging and has yet to realize the high conversion efficiency. To explore the device performance, the impact of thickness variation has been studied. SCAPS-1D tool is used to perform all the device simulations. The proposed device structure of Cu/PEDOT: PSS + WO 3 /FASnI 3 /PC 61 Bm/FTO is designed. In this proposed work, the thickness of FASnI 3 absorber is varied from 50 to 500 nm. After doing the variation, the device performance is optimized at 400 nm which provides higher PV parameters J SC of 24.78 mA/cm 2 , V OC of 0.951 V, FF of 78.75% and PCE of 16.74%. The reported results are providing the insight for further development of PV devices and can help to enhance the tin-based device performance.
- 24 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Numerical Simulations of FASnI3 based Solar Cell with the Variation of Absorber Layer Thickness
Tin based solar cells are considered as a promising contender in the photovoltaic (PV) industry. However, the performance of PV devices based on Formamidinium tin iodide (FASnI 3 ) material is still lagging and has yet to realize the high conversion efficiency. To explore the device performance, the impact of thickness variation has been studied. SCAPS-1D tool is used to perform all the device simulations. The proposed device structure of Cu/PEDOT: PSS + WO 3 /FASnI 3 /PC 61 Bm/FTO is designed. In this proposed work, the thickness of FASnI 3 absorber is varied from 50 to 500 nm. After doing the variation, the device performance is optimized at 400 nm which provides higher PV parameters J SC of 24.78 mA/cm 2 , V OC of 0.951 V, FF of 78.75% and PCE of 16.74%. The reported results are providing the insight for further development of PV devices and can help to enhance the tin-based device performance.
- 21 March 2022
- Published by Springer Nature in Journal of Optics
- Vol. 51 (3) , 672-677
Numerical simulations of double nanograting based plasmonic photodetector for enhancement in light absorption
- 21 March 2022
- Published by Springer Nature in Journal of Optics
- Vol. 51 (3) , 672-677
Numerical simulations of double nanograting based plasmonic photodetector for enhancement in light absorption
- 21 December 2021
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 32 (2) , 025001
Process and device simulations aimed at improving the emitter region performance of silicon PERC solar cells
Achieved levels of silicon-based passivated emitter and rear cell (PERC) solar cells laboratory and module-level conversion efficiencies are still far from the theoretically achievable Auger limit of 29.4% for silicon solar cells, prominently due to emitter recombination and resistive losses. The emitter region in PERC devices is formed by using either ion implantation followed by a diffusion process or POCl 3 diffusion. In ion-implanted emitter-based PERC, the process variables such as dose, energy, diffusion time, and temperature play a vital role in defining the characteristics of the emitter region. Detailed investigation of these parameters could provide a pathway to mitigate the recombination as well as resistive losses; however, it requires a considerable budget to optimize these parameters through a purely experimental approach. Therefore, advanced industrial standard process and device simulation are perceived in this work to carry out the comprehensive study of process variables. Investigation of ion implantation and diffusion process parameters on the PV performance of an upright pyramid textured, industrial standard stacked dielectric passivated PERC solar cell is carried out to deliver 22.8% conversion efficiency with improved PV parameters such as short circuit current density ( J SC ) of 40.8 mA cm −2 , open-circuit voltage ( V OC ) of 686 mV, and fill-factor (FF) of 81.54% at optimized implantation and diffusion parameters, such as implantation dose of 5 × 10 15 cm −2 with energy 30 keV followed 950 °C diffusion temperature and 30 min of diffusion time. The performance of the optimized PERC device is compared with already published large area screen printed contact-based device. This work may open up a window for the experimental work to understand the influence of process parameters on the emitter region to develop the highly efficient PERC solar cell in the future.
- 21 December 2021
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 32 (2) , 025001
Process and device simulations aimed at improving the emitter region performance of silicon PERC solar cells
Achieved levels of silicon-based passivated emitter and rear cell (PERC) solar cells laboratory and module-level conversion efficiencies are still far from the theoretically achievable Auger limit of 29.4% for silicon solar cells, prominently due to emitter recombination and resistive losses. The emitter region in PERC devices is formed by using either ion implantation followed by a diffusion process or POCl 3 diffusion. In ion-implanted emitter-based PERC, the process variables such as dose, energy, diffusion time, and temperature play a vital role in defining the characteristics of the emitter region. Detailed investigation of these parameters could provide a pathway to mitigate the recombination as well as resistive losses; however, it requires a considerable budget to optimize these parameters through a purely experimental approach. Therefore, advanced industrial standard process and device simulation are perceived in this work to carry out the comprehensive study of process variables. Investigation of ion implantation and diffusion process parameters on the PV performance of an upright pyramid textured, industrial standard stacked dielectric passivated PERC solar cell is carried out to deliver 22.8% conversion efficiency with improved PV parameters such as short circuit current density ( J SC ) of 40.8 mA cm −2 , open-circuit voltage ( V OC ) of 686 mV, and fill-factor (FF) of 81.54% at optimized implantation and diffusion parameters, such as implantation dose of 5 × 10 15 cm −2 with energy 30 keV followed 950 °C diffusion temperature and 30 min of diffusion time. The performance of the optimized PERC device is compared with already published large area screen printed contact-based device. This work may open up a window for the experimental work to understand the influence of process parameters on the emitter region to develop the highly efficient PERC solar cell in the future.