Alexander Umanskii
Alexander Umanskii has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- A. E. Gorbunov
Department of Metrology, Instrumentation and Quality Management, Saint-Petersburg Mining University, 2, 21st Line, St. Petersburg 199106, Russia
3 shared publications - Vladimir A. Syasko
D.I. Mendeleev Institute for Metrology (VNIIM), Moskovsky Ave, 19, 190005 St. Petersburg, Russia
3 shared publications - Kirill Igorevich Doronin
Department of Metrology, Instrumentation and Quality Management, Empress Catherine II Saint Petersburg Mining University, 199106 St. Petersburg, Russia
2 shared publications - Kirill Valerievich Gogolinskiy
Petersburg Nuclear Physics Institute named by B.P.Konstantinov of NRC «Kurchatov Institute», Gatchina, Russia
2 shared publications - P. V. Solomenchuk
LLC. “KONSTANTA”, 21, Ogorodny Lane, St. Petersburg 198095, Russia
2 shared publications - Varvara Alekhnovich
Department of Metrology, Instrumentation and Quality Management, Empress Catherine II Saint Petersburg Mining University, 199106 Saint-Petersburg, Russia
2 shared publications
Latest Publications
- Open Access
- 24 September 2026
- Published by MDPI AG in Applied Mechanics
- Vol. 7 (4) , 79
Load-Dependent Instrumented Indentation Test and Local Micromechanical Response near a Pore in Additively Manufactured IN718
In this work, the load-dependent indentation response of as-built Inconel 718 produced by direct laser deposition was studied, followed by local mapping around a single surface-intersecting pore. A working load of 100 mN was selected because the indentation modulus approached a depth-independent plateau and the penetration depth was substantially larger than the measured surface roughness. At this load, the reference matrix response was HIT = 2.69 ± 0.26 GPa and EIT = 160 ± 11 GPa. An equivalent contact radius ac was calculated from the projected contact area, and pore-edge distance was normalized as ξ = s/ac. For the reference response, ac ≈ 3.44 µm and the first numerically defined position at s = 20 µm corresponded to ξ ≈ 5.8. Robust regression of 56 individual measurements showed no statistically resolved dependence of EIT on ξ, whereas a small negative HIT slope was observed and interpreted cautiously because of directional variability. The analysis is restricted to this single pore and to ξ ≥ 5.8; the immediate pore-edge regime was not experimentally resolved. The contact-scale normalization provides a reproducible framework for interpreting local indentation data near a geometrical defect without treating the two-dimensional pore-area fraction as bulk porosity.
- 24 September 2026
- Published by MDPI AG in Applied Mechanics
- Vol. 7 (4) , 79
Open AccessLoad-Dependent Instrumented Indentation Test and Local Micromechanical Response near a Pore in Additively Manufactured IN718
In this work, the load-dependent indentation response of as-built Inconel 718 produced by direct laser deposition was studied, followed by local mapping around a single surface-intersecting pore. A working load of 100 mN was selected because the indentation modulus approached a depth-independent plateau and the penetration depth was substantially larger than the measured surface roughness. At this load, the reference matrix response was HIT = 2.69 ± 0.26 GPa and EIT = 160 ± 11 GPa. An equivalent contact radius ac was calculated from the projected contact area, and pore-edge distance was normalized as ξ = s/ac. For the reference response, ac ≈ 3.44 µm and the first numerically defined position at s = 20 µm corresponded to ξ ≈ 5.8. Robust regression of 56 individual measurements showed no statistically resolved dependence of EIT on ξ, whereas a small negative HIT slope was observed and interpreted cautiously because of directional variability. The analysis is restricted to this single pore and to ξ ≥ 5.8; the immediate pore-edge regime was not experimentally resolved. The contact-scale normalization provides a reproducible framework for interpreting local indentation data near a geometrical defect without treating the two-dimensional pore-area fraction as bulk porosity.
- 1 January 2026
- Published by ITMO University in Reviews on Advanced Materials and Technologies
- Vol. 8 (3)
Estimation of Additive Manufactured Steel Hardness and Elastic Modulus by Instrumented Indentation Test
This work is devoted to mechanical properties estimation of steel samples produced by additive and classic technologies via instrumented indentation test. Features of 3D printing, physical and mechanical properties, methods and means of additive manufacturing products control are described. The experimental part presents a series of indentation tests to determine the parameters of elastic-plastic deformation: hardness and elastic modulus, which are compared to reference data from other studies. The difference in the properties of the material produced by classical technologies and synthesized by direct metal laser sintering (DMLS) from a powder of identical chemical composition is discussed. The elastic modulus varied less for DMLS samples (208–213 GPa) than for cast ones (203–234 GPa). Hardness of the additively manufactured 12Cr18Ni10Тi was also more consistent relative to the differently remelted samples.
- 1 January 2026
- Published by ITMO University in Reviews on Advanced Materials and Technologies
- Vol. 8 (3)
Estimation of Additive Manufactured Steel Hardness and Elastic Modulus by Instrumented Indentation Test
This work is devoted to mechanical properties estimation of steel samples produced by additive and classic technologies via instrumented indentation test. Features of 3D printing, physical and mechanical properties, methods and means of additive manufacturing products control are described. The experimental part presents a series of indentation tests to determine the parameters of elastic-plastic deformation: hardness and elastic modulus, which are compared to reference data from other studies. The difference in the properties of the material produced by classical technologies and synthesized by direct metal laser sintering (DMLS) from a powder of identical chemical composition is discussed. The elastic modulus varied less for DMLS samples (208–213 GPa) than for cast ones (203–234 GPa). Hardness of the additively manufactured 12Cr18Ni10Тi was also more consistent relative to the differently remelted samples.
- Open Access
- 15 February 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (4) , 2036
Methods and Means of Eddy Current Testing of Soldered Lap Joints of Electrical Machines
This article is devoted to the non-destructive testing of the soldering integrity of soldered lap joints of the current-carrying busbars in electrical machines’ stator windings. The design of a two-element eddy current probe with tangentially positioned coils and active shielding for measuring the soldering integrity of soldered lap joints is developed. This paper considers the method of suppressing the influence of stray parameters on the testing results and the method of correcting the measurements in the case of a deviation in the electrical conductivity of the conductive busbar material. The test results demonstrate the performance of the developed eddy current probe for determining the actual value of the soldering integrity of soldered lap joints in the range of 0–100% with a permissible relative error of no more than 5%.
- 15 February 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (4) , 2036
Open AccessMethods and Means of Eddy Current Testing of Soldered Lap Joints of Electrical Machines
This article is devoted to the non-destructive testing of the soldering integrity of soldered lap joints of the current-carrying busbars in electrical machines’ stator windings. The design of a two-element eddy current probe with tangentially positioned coils and active shielding for measuring the soldering integrity of soldered lap joints is developed. This paper considers the method of suppressing the influence of stray parameters on the testing results and the method of correcting the measurements in the case of a deviation in the electrical conductivity of the conductive busbar material. The test results demonstrate the performance of the developed eddy current probe for determining the actual value of the soldering integrity of soldered lap joints in the range of 0–100% with a permissible relative error of no more than 5%.
- 15 August 2024
- Published by The Russian Academy of Sciences in Defektoskopiâ
- No. 8,p. 42-51
Modeling of two-element tangential eddy current probe with active shielding for soldered joints inspection
The paper is devoted to designing a finite-element model of the eddy current probe for testing the degree of soldering of lap soldered joints of conductive busbars. The method for finite-element model designing is developed, which parameters provide calculations error of signals of finite-element model of eddy current probe below 1.5%. The test results confirm the performance of the eddy current probe, the measurement range for soldered joints defect size from 0 to 100 % and provision of the declared basic absolute error of the degree of soldering measurement of 5 %.
- 15 August 2024
- Published by The Russian Academy of Sciences in Defektoskopiâ
- No. 8,p. 42-51
Modeling of two-element tangential eddy current probe with active shielding for soldered joints inspection
The paper is devoted to designing a finite-element model of the eddy current probe for testing the degree of soldering of lap soldered joints of conductive busbars. The method for finite-element model designing is developed, which parameters provide calculations error of signals of finite-element model of eddy current probe below 1.5%. The test results confirm the performance of the eddy current probe, the measurement range for soldered joints defect size from 0 to 100 % and provision of the declared basic absolute error of the degree of soldering measurement of 5 %.
- 1 August 2024
- Published by Pleiades Publishing Ltd in Russian Journal of Nondestructive Testing
- Vol. 60 (8) , 912-920
Modeling a Two-Element Tangential Eddy Current Probe with Active Shielding for Soldered Joint Testing
The paper is devoted to the development of a finite element model of an eddy current probe designed to test the degree of soldering in lap-joint soldered connections of conductive busbars. A methodology for developing a finite element model has been devised that includes a geometric parameter that, when altered, leads to the remeshing of the finite element grid without affecting the test parameters of nondestructive testing. This allows for a series of signal measurements of the finite element model of the eddy current probe, followed by averaging, thereby ensuring acceptable accuracy. The test results confirm the functionality of the eddy current probe, with a defect size measurement range in the soldered joint from 0 to 100% and a guaranteed main absolute error in measuring the degree of soldering of 5%.
- 1 August 2024
- Published by Pleiades Publishing Ltd in Russian Journal of Nondestructive Testing
- Vol. 60 (8) , 912-920
Modeling a Two-Element Tangential Eddy Current Probe with Active Shielding for Soldered Joint Testing
The paper is devoted to the development of a finite element model of an eddy current probe designed to test the degree of soldering in lap-joint soldered connections of conductive busbars. A methodology for developing a finite element model has been devised that includes a geometric parameter that, when altered, leads to the remeshing of the finite element grid without affecting the test parameters of nondestructive testing. This allows for a series of signal measurements of the finite element model of the eddy current probe, followed by averaging, thereby ensuring acceptable accuracy. The test results confirm the functionality of the eddy current probe, with a defect size measurement range in the soldered joint from 0 to 100% and a guaranteed main absolute error in measuring the degree of soldering of 5%.
- Open Access
- 15 July 2024
- Published by MDPI AG in Inventions
- Vol. 9 (4) , 78
Multi-Parameter Complex Control of Metal Coatings on Ball Plugs of Pipeline Shut-Off Valves
The greatest losses during gas transportation occur in the elements of shut-off valves, the operating parameters of which, among other things, depend on the thickness and hardness of the protective coating of the ball plugs. The study of the parameters of nickel–phosphorus and chrome coatings on ball plugs of serially produced shut-off valves, including control of their thickness and hardness, was carried out. Based on the test results, deviations in the actual parameters of coatings from the requirements of technological documentation were revealed, the necessity of their complex control was substantiated, recommendations on the choice of methods and equipment were formulated, and the main provisions of the test methodology were developed.
- 15 July 2024
- Published by MDPI AG in Inventions
- Vol. 9 (4) , 78
Open AccessMulti-Parameter Complex Control of Metal Coatings on Ball Plugs of Pipeline Shut-Off Valves
The greatest losses during gas transportation occur in the elements of shut-off valves, the operating parameters of which, among other things, depend on the thickness and hardness of the protective coating of the ball plugs. The study of the parameters of nickel–phosphorus and chrome coatings on ball plugs of serially produced shut-off valves, including control of their thickness and hardness, was carried out. Based on the test results, deviations in the actual parameters of coatings from the requirements of technological documentation were revealed, the necessity of their complex control was substantiated, recommendations on the choice of methods and equipment were formulated, and the main provisions of the test methodology were developed.
- Open Access
- 13 December 2022
- Published by MDPI AG in Inventions
- Vol. 7 (4) , 125
Method of the Mechanical Properties Evaluation of Polyethylene Gas Pipelines with Portable Hardness Testers
This article is devoted to the study of means and methods for non-destructive testing mechanical properties of polyethylene gas pipelines that have been in operation for 25–55 years. In order to assess mechanical properties, stress at yield was chosen as a key parameter. Stress at yield is determined from the results of tensile tests and is associated with the limiting circumferential (hoop) stress, determined from the results of tests for short-term pressure. Tensile tests require sample cutting and the shutdown of pipelines’ service. To solve this problem of nondestructive testing of pipelines, tests were carried out using the methods of Shore, Leeb and dynamic instrumental indentation. According to the test results, it was revealed that the correlation coefficient between the values of stress at yield and hardness, obtained by the method of dynamic instrumental indentation, is 0.98 which confirms the possibility of the evaluation of the mechanical properties of pipelines by the method of dynamic instrumental indentation.
- 13 December 2022
- Published by MDPI AG in Inventions
- Vol. 7 (4) , 125
Open AccessMethod of the Mechanical Properties Evaluation of Polyethylene Gas Pipelines with Portable Hardness Testers
This article is devoted to the study of means and methods for non-destructive testing mechanical properties of polyethylene gas pipelines that have been in operation for 25–55 years. In order to assess mechanical properties, stress at yield was chosen as a key parameter. Stress at yield is determined from the results of tensile tests and is associated with the limiting circumferential (hoop) stress, determined from the results of tests for short-term pressure. Tensile tests require sample cutting and the shutdown of pipelines’ service. To solve this problem of nondestructive testing of pipelines, tests were carried out using the methods of Shore, Leeb and dynamic instrumental indentation. According to the test results, it was revealed that the correlation coefficient between the values of stress at yield and hardness, obtained by the method of dynamic instrumental indentation, is 0.98 which confirms the possibility of the evaluation of the mechanical properties of pipelines by the method of dynamic instrumental indentation.
- Open Access
- 28 February 2022
- Published by MDPI AG in Inventions
- Vol. 7 (1) , 29
Modification of the Leeb Impact Device for Measuring Hardness by the Dynamic Instrumented Indentation Method
The article is devoted to modification of the impact devices of Leeb hardness testers for the implementation of the dynamic instrumented indentation method. The results obtained made it possible to construct a load–displacement curve using primary EMF signals and made it possible to determine the values of the dissipated and elastic impact body energy, the maximal load of indentation, the maximal and residual penetration depth and the geometric parameters of the indentation region, namely the contact area of the indenter with the surface and the volume of the displaced material. The listed parameters of the indentation process allow us to measure the contact and volume hardness, the elastic modulus and the yield strength of test objects with portable hardness testers.
- 28 February 2022
- Published by MDPI AG in Inventions
- Vol. 7 (1) , 29
Open AccessModification of the Leeb Impact Device for Measuring Hardness by the Dynamic Instrumented Indentation Method
The article is devoted to modification of the impact devices of Leeb hardness testers for the implementation of the dynamic instrumented indentation method. The results obtained made it possible to construct a load–displacement curve using primary EMF signals and made it possible to determine the values of the dissipated and elastic impact body energy, the maximal load of indentation, the maximal and residual penetration depth and the geometric parameters of the indentation region, namely the contact area of the indenter with the surface and the volume of the displaced material. The listed parameters of the indentation process allow us to measure the contact and volume hardness, the elastic modulus and the yield strength of test objects with portable hardness testers.
- Open Access
- 1 November 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1384 (1) , 012012
Mechanical properties measurements with portable hardness testers: advantages, limitations, prospects
The article presents an analysis of the most common hardness measurement methods, implemented by portable hardness testers: rebound or Leeb method, static Portable Rockwell (PR) method and Ultrasonic Contact Impedance (UCI) method. These methods are reviewed in terms of the physical nature of the measurements and the influence of the measured sample properties and the probe parameters on the measurement result. The review contains advantages of each method, possible applications, as well as limitations due to the operation principles of probes. The article also contains the analysis of solving the problem of measurement results validity and their conformity with standardized hardness scales.
- 1 November 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1384 (1) , 012012
Open AccessMechanical properties measurements with portable hardness testers: advantages, limitations, prospects
The article presents an analysis of the most common hardness measurement methods, implemented by portable hardness testers: rebound or Leeb method, static Portable Rockwell (PR) method and Ultrasonic Contact Impedance (UCI) method. These methods are reviewed in terms of the physical nature of the measurements and the influence of the measured sample properties and the probe parameters on the measurement result. The review contains advantages of each method, possible applications, as well as limitations due to the operation principles of probes. The article also contains the analysis of solving the problem of measurement results validity and their conformity with standardized hardness scales.