Toshihiko Asami
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Toshihiko Asami has a total of 88 co-authors. Here are the top co-authors by number of shared publications:
Hisayoshi Sekiguchi
19 shared publications- Tomohiko Ise
Toyohashi University of Technology
17 shared publications Itsuro Honda
University of Hyogo
15 shared publicationsTomohiko Ise
Toyohashi University of Technology, Toyohashi, Japan
12 shared publicationsHiroya Sakamoto
Tokkyokiki Corporation, Amagasaki, Hyogo, Japan
9 shared publicationsFumiyoshi Kimura
University of Hyogo
8 shared publications
Latest Publications
- Open Access
- 1 January 2022
- Published by Japan Society of Mechanical Engineers in Mechanical Engineering Journal
- Vol. 9 (1) , 21-00362
Relationship between the reciprocity of transfer functions for mechanical vibration systems and optimal design formulas of dynamic vibration absorbers
Transfer functions are often employed to evaluate the vibration characteristics of mechanical and electrical systems. Within a group of transfer functions, some particular ones have the property that swapping the coefficients of the two terms in the equation does not change the properties of the original function. Such functions are said to have a reciprocity property. Mechanical vibratory systems typically have three transfer functions; namely, compliance, mobility, and accelerance. For a single-degree-of-freedom system, the mobility transfer function has the reciprocity property; for a two-degree-of-freedom system, no transfer function has the reciprocity property; and for a three-degree-of-freedom system, one transfer function has the reciprocity property. This paper shows that the presence of transfer functions with the reciprocity property is extremely important for obtaining simple optimal design formulas for dynamic vibration absorbers.
- 1 January 2022
- Published by Japan Society of Mechanical Engineers in Mechanical Engineering Journal
- Vol. 9 (1) , 21-00362
Open AccessRelationship between the reciprocity of transfer functions for mechanical vibration systems and optimal design formulas of dynamic vibration absorbers
Transfer functions are often employed to evaluate the vibration characteristics of mechanical and electrical systems. Within a group of transfer functions, some particular ones have the property that swapping the coefficients of the two terms in the equation does not change the properties of the original function. Such functions are said to have a reciprocity property. Mechanical vibratory systems typically have three transfer functions; namely, compliance, mobility, and accelerance. For a single-degree-of-freedom system, the mobility transfer function has the reciprocity property; for a two-degree-of-freedom system, no transfer function has the reciprocity property; and for a three-degree-of-freedom system, one transfer function has the reciprocity property. This paper shows that the presence of transfer functions with the reciprocity property is extremely important for obtaining simple optimal design formulas for dynamic vibration absorbers.
- Open Access
- 1 January 2021
- Published by Japan Society of Mechanical Engineers in Mechanical Engineering Journal
- Vol. 8 (5) , 21-00189
Simple exact solutions for designing an optimal mechanical dynamic vibration absorber combined with a piezoelectric LR circuit based on the H∞, H2, or stability criterion
Multiplexing dynamic vibration absorbers (DVAs) provide better vibration control compared to that obtained with single-mass DVAs; however, their structure is more complicated and they are thus difficult to apply in practice. This paper proposes several optimal design formulas for an electromechanical DVA in which a mechanical single-mass DVA with a piezoelectric element between the primary and absorber masses and a series LR circuit is coupled to the element. The inductor and piezoelectric element act as a virtual mass and a virtual spring, respectively, and thus the circuit works as a kind of double-mass DVA. In the present study, such an electromechanical DVA was optimized based on three design criteria and its design formulas were derived. Such design formulas have been previously reported, but they are very long and impractical. In contrast, the proposed formulas are very simple and the optimal design conditions for a DVA can be easily obtained. The steady-state and free-vibration responses of a three-degree-of-freedom system with an optimized electromechanical DVA are compared with those of a vibratory system with a mechanical series-type double-mass DVA. It is confirmed that the electromechanical DVA exhibits exactly the same vibration suppression performance as that of the mechanical DVA.
- 1 January 2021
- Published by Japan Society of Mechanical Engineers in Mechanical Engineering Journal
- Vol. 8 (5) , 21-00189
Open AccessSimple exact solutions for designing an optimal mechanical dynamic vibration absorber combined with a piezoelectric LR circuit based on the H∞, H2, or stability criterion
Multiplexing dynamic vibration absorbers (DVAs) provide better vibration control compared to that obtained with single-mass DVAs; however, their structure is more complicated and they are thus difficult to apply in practice. This paper proposes several optimal design formulas for an electromechanical DVA in which a mechanical single-mass DVA with a piezoelectric element between the primary and absorber masses and a series LR circuit is coupled to the element. The inductor and piezoelectric element act as a virtual mass and a virtual spring, respectively, and thus the circuit works as a kind of double-mass DVA. In the present study, such an electromechanical DVA was optimized based on three design criteria and its design formulas were derived. Such design formulas have been previously reported, but they are very long and impractical. In contrast, the proposed formulas are very simple and the optimal design conditions for a DVA can be easily obtained. The steady-state and free-vibration responses of a three-degree-of-freedom system with an optimized electromechanical DVA are compared with those of a vibratory system with a mechanical series-type double-mass DVA. It is confirmed that the electromechanical DVA exhibits exactly the same vibration suppression performance as that of the mechanical DVA.
- Open Access
- 1 January 2021
- Published by Japan Society of Mechanical Engineers in Mechanical Engineering Journal
- Vol. 8 (3) , 20-00476
Optimal design of a series-type double-mass hysteretically damped dynamic vibration absorber based on the stability criterion
In most dynamic vibration absorbers (DVAs) used in practical applications, polymeric materials that have both restoring capabilities and damping effects are used instead of coil springs as spring elements. It is known that the damping force for such polymeric materials has hysteretic characteristics and varies in proportion to the relative displacement rather than the relative velocity between objects. This paper proposes an optimal design formula for a double-mass hysteretically damped DVA with two masses connected in series. For the design of the DVA in this study, the stability maximization criterion, which attenuates the free-vibration response of the primary system in the shortest time, was adopted. It was found that the optimal design expression for installing the series-type double-mass DVA on an undamped primary system can be expressed by a very simple formula. The maximized stability, which determines the speed of vibration convergence, of the double-mass DVA was 1.7 times that of the corresponding single-mass DVA. When there is damping in the primary system, the optimal design condition for the DVA cannot be expressed with such a simple formula, but an equation to calculate it is presented in this paper. The equation can be easily solved numerically, and the results show that the stability of the system is further increased compared to the undamped primary system.
- 1 January 2021
- Published by Japan Society of Mechanical Engineers in Mechanical Engineering Journal
- Vol. 8 (3) , 20-00476
Open AccessOptimal design of a series-type double-mass hysteretically damped dynamic vibration absorber based on the stability criterion
In most dynamic vibration absorbers (DVAs) used in practical applications, polymeric materials that have both restoring capabilities and damping effects are used instead of coil springs as spring elements. It is known that the damping force for such polymeric materials has hysteretic characteristics and varies in proportion to the relative displacement rather than the relative velocity between objects. This paper proposes an optimal design formula for a double-mass hysteretically damped DVA with two masses connected in series. For the design of the DVA in this study, the stability maximization criterion, which attenuates the free-vibration response of the primary system in the shortest time, was adopted. It was found that the optimal design expression for installing the series-type double-mass DVA on an undamped primary system can be expressed by a very simple formula. The maximized stability, which determines the speed of vibration convergence, of the double-mass DVA was 1.7 times that of the corresponding single-mass DVA. When there is damping in the primary system, the optimal design condition for the DVA cannot be expressed with such a simple formula, but an equation to calculate it is presented in this paper. The equation can be easily solved numerically, and the results show that the stability of the system is further increased compared to the undamped primary system.
- 1 January 2020
- Published by Japan Society of Mechanical Engineers in Mechanical Engineering Journal
- Vol. 7 (2) , 19-00482
Optimal design of a hysteretically damped dynamic vibration absorber
In the optimization of dynamic vibration absorbers (DVAs), it is generally assumed that the damping force changes in proportion to the velocity of the object; this damping is called viscous damping. However, many DVAs used in practical applications are made of polymeric rubber materials having both restorative and damping effects. This polymer material is considered to show a hysteretic damping force that is proportional to the displacement rather than the velocity of the object. Despite the widespread use of such hysteretically damped DVAs, there are very few studies on their optimal design, and the design formula of the well-known general viscously damped DVA is presently used for the design of this type of DVA. This article reports the optimal solution of this hysteretically damped DVA. For generality, it is assumed that the primary system also has structural damping that can be treated as hysteretic damping. Three optimization criteria, namely the H∞ optimization, H2 optimization, and stability maximization criteria, were adopted for the optimization of the DVA. For the H∞ optimization and stability maximization criteria, exact algebraic solutions were successfully derived, and for the H2 criterion, simultaneous equations with six unknowns and their numerical solutions were obtained.
- 1 January 2020
- Published by Japan Society of Mechanical Engineers in Mechanical Engineering Journal
- Vol. 7 (2) , 19-00482
Optimal design of a hysteretically damped dynamic vibration absorber
In the optimization of dynamic vibration absorbers (DVAs), it is generally assumed that the damping force changes in proportion to the velocity of the object; this damping is called viscous damping. However, many DVAs used in practical applications are made of polymeric rubber materials having both restorative and damping effects. This polymer material is considered to show a hysteretic damping force that is proportional to the displacement rather than the velocity of the object. Despite the widespread use of such hysteretically damped DVAs, there are very few studies on their optimal design, and the design formula of the well-known general viscously damped DVA is presently used for the design of this type of DVA. This article reports the optimal solution of this hysteretically damped DVA. For generality, it is assumed that the primary system also has structural damping that can be treated as hysteretic damping. Three optimization criteria, namely the H∞ optimization, H2 optimization, and stability maximization criteria, were adopted for the optimization of the DVA. For the H∞ optimization and stability maximization criteria, exact algebraic solutions were successfully derived, and for the H2 criterion, simultaneous equations with six unknowns and their numerical solutions were obtained.
- 1 January 2020
- Published by Japan Society of Mechanical Engineers in Mechanical Engineering Journal
- Vol. 7 (2) , 19-00051
Numerical solutions for optimal double-mass dynamic vibration absorbers attached to a damped primary system
Because double-mass dynamic vibration absorbers (DVAs) are superior to single-mass DVAs in terms of their vibration suppression performance and robustness, they have been increasingly studied recently. The optimization of double-mass DVAs is much more difficult than that of single-mass DVAs. However, recently, the ability of formula manipulation solvers typified by Mathematica has greatly improved, and exact algebraic solutions have been obtained for double-mass DVAs. The optimal solution for a double-mass DVA attached to a damped primary system has been reported in the form of an exact algebraic solution in a previous report. That paper reported the algebraic optimal solutions for a series-type double-mass DVA for the compliance and mobility transfer functions of the primary system successfully obtained by applying three different optimization criteria: H-infinity optimization, H-2 optimization, and stability maximization. In the present article, the numerical solutions to optimization problems for double-mass DVAs that cannot be algebraically solved are presented. There are two types of double-mass DVAs: series- and parallel-type DVAs. When applying the three optimization criteria mentioned above to each of them, there exist a total of 22 different optimal solutions because there are three transfer functions- the compliance, mobility, and accelerance transfer functions-that are typically used to describe the absolute response of the primary system. Of these 22 solutions, 10 solutions for the compliance transfer function are introduced in this article.
- 1 January 2020
- Published by Japan Society of Mechanical Engineers in Mechanical Engineering Journal
- Vol. 7 (2) , 19-00051
Numerical solutions for optimal double-mass dynamic vibration absorbers attached to a damped primary system
Because double-mass dynamic vibration absorbers (DVAs) are superior to single-mass DVAs in terms of their vibration suppression performance and robustness, they have been increasingly studied recently. The optimization of double-mass DVAs is much more difficult than that of single-mass DVAs. However, recently, the ability of formula manipulation solvers typified by Mathematica has greatly improved, and exact algebraic solutions have been obtained for double-mass DVAs. The optimal solution for a double-mass DVA attached to a damped primary system has been reported in the form of an exact algebraic solution in a previous report. That paper reported the algebraic optimal solutions for a series-type double-mass DVA for the compliance and mobility transfer functions of the primary system successfully obtained by applying three different optimization criteria: H-infinity optimization, H-2 optimization, and stability maximization. In the present article, the numerical solutions to optimization problems for double-mass DVAs that cannot be algebraically solved are presented. There are two types of double-mass DVAs: series- and parallel-type DVAs. When applying the three optimization criteria mentioned above to each of them, there exist a total of 22 different optimal solutions because there are three transfer functions- the compliance, mobility, and accelerance transfer functions-that are typically used to describe the absolute response of the primary system. Of these 22 solutions, 10 solutions for the compliance transfer function are introduced in this article.
- 14 June 2019
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 141 (5) , 1-23
Exact Algebraic Solution of an Optimal Double-Mass Dynamic Vibration Absorber Attached to a Damped Primary System
This article presents exact algebraic solutions to optimization problems of a double-mass dynamic vibration absorber (DVA) attached to a viscous damped primary system. The series-type double-mass DVA was optimized using three optimization criteria (the H∞ optimization, H2 optimization, and stability maximization criteria), and exact algebraic solutions were successfully obtained for all of them. It is extremely difficult to optimize DVAs when there is damping in the primary system. Even in the optimization of the simpler single-mass DVA, exact solutions have been obtained only for the H2 optimization and stability maximization criteria. For H∞ optimization, only numerical solutions and an approximate perturbation solution have been obtained. Regarding double-mass DVAs, an exact algebraic solution could not be obtained in this study in the case where a parallel-type DVA is attached to the damped primary system. For the series-type double mass DVA, which was the focus of the present study, an exact algebraic solution was obtained for the force excitation system, in which the disturbance force acts directly on the primary mass; however, an algebraic solution was not obtained for the motion excitation system, in which the foundation of the system is subjected to a periodic displacement. Because all actual vibration systems involve damping, the results obtained in this study are expected to be useful in the design of actual DVAs. Furthermore, it is a great surprise that an exact algebraic solution exists even for such complex optimization problems of a linear vibration system.
- 14 June 2019
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 141 (5) , 1-23
Exact Algebraic Solution of an Optimal Double-Mass Dynamic Vibration Absorber Attached to a Damped Primary System
This article presents exact algebraic solutions to optimization problems of a double-mass dynamic vibration absorber (DVA) attached to a viscous damped primary system. The series-type double-mass DVA was optimized using three optimization criteria (the H∞ optimization, H2 optimization, and stability maximization criteria), and exact algebraic solutions were successfully obtained for all of them. It is extremely difficult to optimize DVAs when there is damping in the primary system. Even in the optimization of the simpler single-mass DVA, exact solutions have been obtained only for the H2 optimization and stability maximization criteria. For H∞ optimization, only numerical solutions and an approximate perturbation solution have been obtained. Regarding double-mass DVAs, an exact algebraic solution could not be obtained in this study in the case where a parallel-type DVA is attached to the damped primary system. For the series-type double mass DVA, which was the focus of the present study, an exact algebraic solution was obtained for the force excitation system, in which the disturbance force acts directly on the primary mass; however, an algebraic solution was not obtained for the motion excitation system, in which the foundation of the system is subjected to a periodic displacement. Because all actual vibration systems involve damping, the results obtained in this study are expected to be useful in the design of actual DVAs. Furthermore, it is a great surprise that an exact algebraic solution exists even for such complex optimization problems of a linear vibration system.
- 1 April 2019
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Transactions on Electronics, Information and Systems
- Vol. 139 (4) , 323-329
An Adaptive Allocator Design for An Input Redundant System with Two Input Channels
In this paper, we propose a design method of an adaptive control system for input redundant 2 input 1 output system. The feature of the proposed method is that the control input can be adjusted by an arbitrary external signal by utilizing the degree of freedom of the control input in the input redundant system, and the reference model output tracking can be achieved. A numerical example is shown at the end of this paper, and the proposed method is verified.
- 1 April 2019
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Transactions on Electronics, Information and Systems
- Vol. 139 (4) , 323-329
An Adaptive Allocator Design for An Input Redundant System with Two Input Channels
In this paper, we propose a design method of an adaptive control system for input redundant 2 input 1 output system. The feature of the proposed method is that the control input can be adjusted by an arbitrary external signal by utilizing the degree of freedom of the control input in the input redundant system, and the reference model output tracking can be achieved. A numerical example is shown at the end of this paper, and the proposed method is verified.
- 1 January 2019
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2019, S05507P
Evaluation of Unsteady Flow Characteristics and Damping Characteristics of Orifice in Shock Absorber
The shock absorber is a device that reduces the vibration of the vehicle and improves ride comfort and maneuverability. The vehicle changes its posture depending on the driving conditions such as sudden start and sudden braking. Therefore, the performance of shock absorbers has been evaluated under many conditions. However, the influence of internal fluid (braking oil) has not been investigated in detail. The shock absorber generates damping force from the internal fluid resistance. It is important at design sites to investigate the impact of internal flow, which is a direct source of damping forces, on the performance of shock absorbers. Therefore, this study evaluates the performance of the shock absorber focusing on the internal fluid. The damping force of the shock absorber is composed of friction drag acting on the side of the piston and pressure drag acting on the front and back of the piston. The main factor is the pre-piston pressure drag. The cause of pressure drag is the pressure difference generated by the passage of fluid through an orifice provided in the piston or cylinder. Therefore, the generated pressure drag differs depending on the orifice shape. Therefore, the investigation of the internal fluid is carried out with multiple orifices. Since various parameter changes are required to investigate the influence of the internal fluid, numerical analysis that is easy for this is adopted as a method of performance evaluation..
- 1 January 2019
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2019, S05507P
Evaluation of Unsteady Flow Characteristics and Damping Characteristics of Orifice in Shock Absorber
The shock absorber is a device that reduces the vibration of the vehicle and improves ride comfort and maneuverability. The vehicle changes its posture depending on the driving conditions such as sudden start and sudden braking. Therefore, the performance of shock absorbers has been evaluated under many conditions. However, the influence of internal fluid (braking oil) has not been investigated in detail. The shock absorber generates damping force from the internal fluid resistance. It is important at design sites to investigate the impact of internal flow, which is a direct source of damping forces, on the performance of shock absorbers. Therefore, this study evaluates the performance of the shock absorber focusing on the internal fluid. The damping force of the shock absorber is composed of friction drag acting on the side of the piston and pressure drag acting on the front and back of the piston. The main factor is the pre-piston pressure drag. The cause of pressure drag is the pressure difference generated by the passage of fluid through an orifice provided in the piston or cylinder. Therefore, the generated pressure drag differs depending on the orifice shape. Therefore, the investigation of the internal fluid is carried out with multiple orifices. Since various parameter changes are required to investigate the influence of the internal fluid, numerical analysis that is easy for this is adopted as a method of performance evaluation..
- 18 June 2018
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 140 (6) , 061012
Optimal Design of Double-Mass Dynamic Vibration Absorbers Minimizing the Mobility Transfer Function
Although the vibration suppression effects of precisely adjusted dynamic vibration absorbers (DVAs) are well known, multimass DVAs have recently been studied with the aim of further improving their performance and avoiding performance deterioration due to changes in their system parameters. One of the present authors has previously reported a solution that provides the optimal tuning and damping conditions of the double-mass DVA and has demonstrated that it achieves better performance than the conventional single-mass DVA. The evaluation index of the performance used in that study was the minimization of the compliance transfer function. This evaluation function has the objective of minimizing the absolute displacement response of the primary system. However, it is important to suppress the absolute velocity response of the primary system to reduce the noise generated by the machine or structure. Therefore, in the present study, the optimal solutions for DVAs were obtained by minimizing the mobility transfer function rather than the compliance transfer function. As in previous investigations, three optimization criteria were tested: the H∞ optimization, H2 optimization, and stability maximization criteria. In this study, an exact algebraic solution to the H∞ optimization of the series-type double-mass DVA was successfully derived. In addition, it was demonstrated that the optimal solution obtained by minimizing the mobility transfer function differs significantly at some points from that minimizing the compliance transfer function published in the previous report.
- 18 June 2018
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 140 (6) , 061012
Optimal Design of Double-Mass Dynamic Vibration Absorbers Minimizing the Mobility Transfer Function
Although the vibration suppression effects of precisely adjusted dynamic vibration absorbers (DVAs) are well known, multimass DVAs have recently been studied with the aim of further improving their performance and avoiding performance deterioration due to changes in their system parameters. One of the present authors has previously reported a solution that provides the optimal tuning and damping conditions of the double-mass DVA and has demonstrated that it achieves better performance than the conventional single-mass DVA. The evaluation index of the performance used in that study was the minimization of the compliance transfer function. This evaluation function has the objective of minimizing the absolute displacement response of the primary system. However, it is important to suppress the absolute velocity response of the primary system to reduce the noise generated by the machine or structure. Therefore, in the present study, the optimal solutions for DVAs were obtained by minimizing the mobility transfer function rather than the compliance transfer function. As in previous investigations, three optimization criteria were tested: the H∞ optimization, H2 optimization, and stability maximization criteria. In this study, an exact algebraic solution to the H∞ optimization of the series-type double-mass DVA was successfully derived. In addition, it was demonstrated that the optimal solution obtained by minimizing the mobility transfer function differs significantly at some points from that minimizing the compliance transfer function published in the previous report.
- 20 October 2017
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 140 (2)
Erratum: “Optimal Design of Double-Mass Dynamic Vibration Absorbers Arranged in Series or in Parallel” [ASME J. Vib. Acoust., 2017, 139(1), p. 011015; DOI: 10.1115/1.4034776]
This paper considers the optimal design of double-mass dynamic vibration absorbers (DVAs) attached to an undamped single-degree-of-freedom system. Three different optimization criteria, the Hinf optimization, H2 optimization, and stability maximization criteria, were considered for the design of the DVAs, and a performance index was defined for each of these criteria. First, the analytical models of vibratory systems with double-mass DVAs were considered, and seven dimensionless parameters were defined. Five of these parameters must be optimized to minimize or maximize the performance indices. Assuming that all dimensionless parameters are nonnegative, the optimal value of one parameter for a double-mass DVA arranged in series (series-type DVA) was proven to be zero. The optimal adjustment conditions of the other four parameters were derived as simple algebraic formulae for the H2 and stability criteria and numerically determined for the Hinf criterion. For a double-mass DVA arranged in parallel (parallel-type DVA), all five parameters were found to have nonzero optimal values, and these values were obtained numerically by solving simultaneous algebraic equations. Second, the performance of these DVAs was compared with a single-mass DVA. The result revealed that for all optimization criteria, the performance of the series-type DVA is the best among the three DVAs and that of the single-mass DVA is the worst. Finally, a procedure for deriving the algebraic or numerical solutions for H2 optimization is described. The derivation procedure of other optimal solutions will be introduced in the future paper.
- 20 October 2017
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 140 (2)
Erratum: “Optimal Design of Double-Mass Dynamic Vibration Absorbers Arranged in Series or in Parallel” [ASME J. Vib. Acoust., 2017, 139(1), p. 011015; DOI: 10.1115/1.4034776]
This paper considers the optimal design of double-mass dynamic vibration absorbers (DVAs) attached to an undamped single-degree-of-freedom system. Three different optimization criteria, the Hinf optimization, H2 optimization, and stability maximization criteria, were considered for the design of the DVAs, and a performance index was defined for each of these criteria. First, the analytical models of vibratory systems with double-mass DVAs were considered, and seven dimensionless parameters were defined. Five of these parameters must be optimized to minimize or maximize the performance indices. Assuming that all dimensionless parameters are nonnegative, the optimal value of one parameter for a double-mass DVA arranged in series (series-type DVA) was proven to be zero. The optimal adjustment conditions of the other four parameters were derived as simple algebraic formulae for the H2 and stability criteria and numerically determined for the Hinf criterion. For a double-mass DVA arranged in parallel (parallel-type DVA), all five parameters were found to have nonzero optimal values, and these values were obtained numerically by solving simultaneous algebraic equations. Second, the performance of these DVAs was compared with a single-mass DVA. The result revealed that for all optimization criteria, the performance of the series-type DVA is the best among the three DVAs and that of the single-mass DVA is the worst. Finally, a procedure for deriving the algebraic or numerical solutions for H2 optimization is described. The derivation procedure of other optimal solutions will be introduced in the future paper.