Tayebeh Mousavi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tayebeh Mousavi has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- Susannah C. Speller
Department of Materials, University of Oxford, Parks Road, Oxford OX1 3PH, United Kingdom
14 shared publications - Fathallah Karimzadeh
Department of Materials Engineering, Isfahan University of Technology, Isfahan, Iran
8 shared publications Chris Grovenor
Department of Materials, University of Oxford, Oxford, UK
7 shared publications- Mark D. Ainslie
Department of Engineering, King's College London, Strand, London WC2R 2LS, United Kingdom
5 shared publications M.H. Abbasi
4 shared publicationsC R M Grovenor
Materials Department, Oxford University, Oxford, OX1 3PH, UK
3 shared publications
Latest Publications
- Open Access
- 22 April 2026
- Published by Springer Nature in Journal of Superconductivity and Novel Magnetism
- Vol. 39 (3) , 80
Pb-free Solders for Joint Developments Between YBCO Tapes
- 22 April 2026
- Published by Springer Nature in Journal of Superconductivity and Novel Magnetism
- Vol. 39 (3) , 80
Open AccessPb-free Solders for Joint Developments Between YBCO Tapes
- 10 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Impact of Ga Addition to InSn Solder on ReBCO Joint Performance
Reliable, robust, low-resistance joints are essential for long-length ReBCO conductors used in high-field superconducting magnets. Yet, common solder joints, such as those made with InSn, suffer from limited mechanical robustness and degradation. This study investigates the influence of adding gallium (Ga) as a minor alloying element (1-7 wt.%) to the eutectic InSn solder for joining commercial ReBCO (YBCO) coated-conductor tapes. Face-to-face lap joints were fabricated using In-Sn-Ga solders and characterized in terms of electrical resistance, microstructure, and mechanical properties. Adding Ga to the eutectic InSn solder decreased the melting points, which is beneficial for joining delicate YBCO tapes. The results showed the formation of a Ga-rich interfacial layer with a CuGa2 composition, leading to a slight increase in the joint electrical resistance compared to binary eutectic InSn. However, mechanical testing revealed that moderate Ga contents (in the range of 1-3 wt.%) improved the joint strength by up to 46% compared to binary eutectic InSn solder. These results indicate that controlled Ga additions can mechanically reinforce the joint without severe electrical degradation, providing a practical approach towards stronger, more reliable joints for ReBCO magnet applications.
- 10 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Impact of Ga Addition to InSn Solder on ReBCO Joint Performance
Reliable, robust, low-resistance joints are essential for long-length ReBCO conductors used in high-field superconducting magnets. Yet, common solder joints, such as those made with InSn, suffer from limited mechanical robustness and degradation. This study investigates the influence of adding gallium (Ga) as a minor alloying element (1-7 wt.%) to the eutectic InSn solder for joining commercial ReBCO (YBCO) coated-conductor tapes. Face-to-face lap joints were fabricated using In-Sn-Ga solders and characterized in terms of electrical resistance, microstructure, and mechanical properties. Adding Ga to the eutectic InSn solder decreased the melting points, which is beneficial for joining delicate YBCO tapes. The results showed the formation of a Ga-rich interfacial layer with a CuGa2 composition, leading to a slight increase in the joint electrical resistance compared to binary eutectic InSn. However, mechanical testing revealed that moderate Ga contents (in the range of 1-3 wt.%) improved the joint strength by up to 46% compared to binary eutectic InSn solder. These results indicate that controlled Ga additions can mechanically reinforce the joint without severe electrical degradation, providing a practical approach towards stronger, more reliable joints for ReBCO magnet applications.
- 9 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Numerical Simulation of High-Field Bulk Superconducting Magnet Reinforcement Using Beryllium Copper
Trapped fields exceeding 20 T are theoretically achievable bulk, single-grain high-temperature superconductors (HTS), making them promising candidates for high-field magnet applications. Experimentally, trapped fields above 17 T have been achieved using mechanical reinforcement such as resin impregnation with carbon-fibre wrapping or shrink fitted stainless steel (SUS). However, because these materials have low thermal conductivity, issues such as localised heating and flux jump instabilities remain during the magnetization process. This study investigates beryllium copper (BeCu) as an alternative reinforcement, leveraging its superior thermal conductivity and mechanical strength at cryogenic temperatures. A numerical field cooled magnetization study was conducted using finite-element models to compare the performance of bulk HTS magnets reinforced with either SUS or BeCu rings. Results show that BeCu reinforcement provides higher compressive stress, improved thermal stability, and higher trapped field. The study is extended to simulate a previously reported experiment in which flux jumps limited the trapped field to below 20 T; under identical conditions, replacing SUS with BeCu suppresses flux jumps and maintains thermal stability. Stress analysis reveals that BeCu enables greater pre-stress due to its higher thermal expansion coefficient. Additional simulations under a 25 T applied field demonstrate that BeCu-reinforced magnets could trap over 22 T at 11 K, suggesting enhanced performance and potential for surpassing current bulk HTS magnetization records.
- 9 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Numerical Simulation of High-Field Bulk Superconducting Magnet Reinforcement Using Beryllium Copper
Trapped fields exceeding 20 T are theoretically achievable bulk, single-grain high-temperature superconductors (HTS), making them promising candidates for high-field magnet applications. Experimentally, trapped fields above 17 T have been achieved using mechanical reinforcement such as resin impregnation with carbon-fibre wrapping or shrink fitted stainless steel (SUS). However, because these materials have low thermal conductivity, issues such as localised heating and flux jump instabilities remain during the magnetization process. This study investigates beryllium copper (BeCu) as an alternative reinforcement, leveraging its superior thermal conductivity and mechanical strength at cryogenic temperatures. A numerical field cooled magnetization study was conducted using finite-element models to compare the performance of bulk HTS magnets reinforced with either SUS or BeCu rings. Results show that BeCu reinforcement provides higher compressive stress, improved thermal stability, and higher trapped field. The study is extended to simulate a previously reported experiment in which flux jumps limited the trapped field to below 20 T; under identical conditions, replacing SUS with BeCu suppresses flux jumps and maintains thermal stability. Stress analysis reveals that BeCu enables greater pre-stress due to its higher thermal expansion coefficient. Additional simulations under a 25 T applied field demonstrate that BeCu-reinforced magnets could trap over 22 T at 11 K, suggesting enhanced performance and potential for surpassing current bulk HTS magnetization records.
- Open Access
- 23 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Fabrication and Characterization of Al-Doped MgB 2 Superconducting Bulks
In this study, Al-doped MgB2 bulks with different doping levels (Al contents of 1-5 at%) were fabricated by a ball-milling process followed by spark plasma sintering in order to improve the current density of MgB2 by doping especially at elevated magnetic fields. The microstructure and superconducting properties of the MgB2 before and after sintering were investigated. It was found that the particle size of Al reduces through the ball-milling process, and the small Al particles gradually dissolve into MgB2 powder, changing the lattice parameters of the MgB2 structure. The Al-doped-MgB2 bulks showed remarkably improved connectivity, higher density and lower MgO impurity compared to the undoped MgB2 with reasonably high critical current density (∼338 kAcm-2 at 1 T and 20 K). Al doping led to an enhancement in the critical current density without significant reductions in transition temperature.
- 23 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Open AccessFabrication and Characterization of Al-Doped MgB 2 Superconducting Bulks
In this study, Al-doped MgB2 bulks with different doping levels (Al contents of 1-5 at%) were fabricated by a ball-milling process followed by spark plasma sintering in order to improve the current density of MgB2 by doping especially at elevated magnetic fields. The microstructure and superconducting properties of the MgB2 before and after sintering were investigated. It was found that the particle size of Al reduces through the ball-milling process, and the small Al particles gradually dissolve into MgB2 powder, changing the lattice parameters of the MgB2 structure. The Al-doped-MgB2 bulks showed remarkably improved connectivity, higher density and lower MgO impurity compared to the undoped MgB2 with reasonably high critical current density (∼338 kAcm-2 at 1 T and 20 K). Al doping led to an enhancement in the critical current density without significant reductions in transition temperature.
- 11 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-6
Numerical Simulation of a Bulk Superconductor-Based Millifluidic Magnetic Separation Chip
The separation of magnetic micro- and nanoparticles based on their size and magnetic properties can greatly enhance their potential in chemical, biological, and medical applications. In this work, we propose a millifluidic magnetic separation chip that employs a bulk superconducting magnet to achieve efficient particle separation. The separation performance of the chip is analysed using the finite-element software package COMSOL Multiphysics. The performance of the chip is investigated under different magnetic conditions, including the use of a permanent magnet and bulk superconducting magnets operating at various temperatures. The results demonstrate that at a bulk operating temperature of 60 K, the system can effectively achieve high-throughput separation of μm-sized magnetic particles with diameters up to 20 μm. The study also reveals that the chip can be utilised for particle size detection. Overall, this modelling framework provides a theoretical foundation for the design and development of practical, high-efficiency mil-lifluidic magnetic separation systems for future applications.
- 11 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-6
Numerical Simulation of a Bulk Superconductor-Based Millifluidic Magnetic Separation Chip
The separation of magnetic micro- and nanoparticles based on their size and magnetic properties can greatly enhance their potential in chemical, biological, and medical applications. In this work, we propose a millifluidic magnetic separation chip that employs a bulk superconducting magnet to achieve efficient particle separation. The separation performance of the chip is analysed using the finite-element software package COMSOL Multiphysics. The performance of the chip is investigated under different magnetic conditions, including the use of a permanent magnet and bulk superconducting magnets operating at various temperatures. The results demonstrate that at a bulk operating temperature of 60 K, the system can effectively achieve high-throughput separation of μm-sized magnetic particles with diameters up to 20 μm. The study also reveals that the chip can be utilised for particle size detection. Overall, this modelling framework provides a theoretical foundation for the design and development of practical, high-efficiency mil-lifluidic magnetic separation systems for future applications.
- 12 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Development of Ag-Added InSn Solders for ReBCO Joints
This study explores ternary Ag-added InSn solders to develop low-resistance, reliable, and mechanically robust joints between YBCO tapes, an essential requirement for superconducting magnets, including the magnets in the fusion industry. To investigate the impact of Ag addition to the widely used SnIn solder, several solders were made by adding small amounts of Ag (1-5wt.% ) to the eutectic In-Sn solder. Lap joints were fabricated between YBCO tapes using these solders and were characterized for electrical resistivity, microstructure, and mechanical properties. According to the results, Ag addition changes the solder bulk structure with minimum impact on the interface and mainly dissolves in the In-rich phase of the solder. The joints made with Ag-added solders show significantly higher mechanical strength and ductility, with fracture shifting from the joint to the tape outside the joint region, and reasonably low electrical resistance. The optimized 5wt.% Ag addition to the binary In-Sn solder showed the best compromised joining performance as a result of a homogenous joint microstructure, offering a promising approach towards more reliable joints for superconducting magnet applications.
- 12 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Development of Ag-Added InSn Solders for ReBCO Joints
This study explores ternary Ag-added InSn solders to develop low-resistance, reliable, and mechanically robust joints between YBCO tapes, an essential requirement for superconducting magnets, including the magnets in the fusion industry. To investigate the impact of Ag addition to the widely used SnIn solder, several solders were made by adding small amounts of Ag (1-5wt.% ) to the eutectic In-Sn solder. Lap joints were fabricated between YBCO tapes using these solders and were characterized for electrical resistivity, microstructure, and mechanical properties. According to the results, Ag addition changes the solder bulk structure with minimum impact on the interface and mainly dissolves in the In-rich phase of the solder. The joints made with Ag-added solders show significantly higher mechanical strength and ductility, with fracture shifting from the joint to the tape outside the joint region, and reasonably low electrical resistance. The optimized 5wt.% Ag addition to the binary In-Sn solder showed the best compromised joining performance as a result of a homogenous joint microstructure, offering a promising approach towards more reliable joints for superconducting magnet applications.
- Open Access
- 17 September 2025
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 54 (11) , 10131-10146
Numerical Investigation of Mirror-Configured ZnTe/CdTe Solar Cells: The Impact of p-Type Window Layers on Performance Enhancement
In this study, the performance of CdTe-based solar cells is investigated using numerical simulations to explore the impact of window layer inversion on device efficiency. Conventional CdTe solar cells typically employ an n-type window layer, but in this work, a p-type ZnTe window layer is introduced to form an inverted device architecture. An experimental setup was also made to validate the numerical data and to practically explore the possibility of such device architecture. The photovoltaic parameters of both conventional (n-ZnTe/n-CdTe/i-CdTe/p-CdTe/p-ZnTe) and inverted (p-ZnTe/p-CdTe/i-CdTe/n-CdTe/n-ZnTe) structures are evaluated using the one-dimensional solar cell capacitance simulator (SCAPS-1D). The results demonstrate that the inverted architecture can enhance power conversion efficiency by up to 45% through optimized structural parameters. The simulated optimal device configuration of TCO/p-ZnTe/p-CdTe/n-CdTe/n-ZnTe/In shows a potential efficiency exceeding 23%, surpassing the current efficiency records for CdTe solar cells. This study presents a numerical investigation of key physical mechanisms, such as the impurity photovoltaic effect (IPV) and impact ionization (II), whose influence on performance is inferred indirectly through carrier dynamics and quantum efficiency trends, given that SCAPS-1D does not explicitly model these effects. Furthermore, these findings highlight the potential of the inverted ZnTe/CdTe device for advanced optoelectronic applications, including bifacial photovoltaics and photoelectrochemical (PEC) hydrogen production.
- 17 September 2025
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 54 (11) , 10131-10146
Open AccessNumerical Investigation of Mirror-Configured ZnTe/CdTe Solar Cells: The Impact of p-Type Window Layers on Performance Enhancement
In this study, the performance of CdTe-based solar cells is investigated using numerical simulations to explore the impact of window layer inversion on device efficiency. Conventional CdTe solar cells typically employ an n-type window layer, but in this work, a p-type ZnTe window layer is introduced to form an inverted device architecture. An experimental setup was also made to validate the numerical data and to practically explore the possibility of such device architecture. The photovoltaic parameters of both conventional (n-ZnTe/n-CdTe/i-CdTe/p-CdTe/p-ZnTe) and inverted (p-ZnTe/p-CdTe/i-CdTe/n-CdTe/n-ZnTe) structures are evaluated using the one-dimensional solar cell capacitance simulator (SCAPS-1D). The results demonstrate that the inverted architecture can enhance power conversion efficiency by up to 45% through optimized structural parameters. The simulated optimal device configuration of TCO/p-ZnTe/p-CdTe/n-CdTe/n-ZnTe/In shows a potential efficiency exceeding 23%, surpassing the current efficiency records for CdTe solar cells. This study presents a numerical investigation of key physical mechanisms, such as the impurity photovoltaic effect (IPV) and impact ionization (II), whose influence on performance is inferred indirectly through carrier dynamics and quantum efficiency trends, given that SCAPS-1D does not explicitly model these effects. Furthermore, these findings highlight the potential of the inverted ZnTe/CdTe device for advanced optoelectronic applications, including bifacial photovoltaics and photoelectrochemical (PEC) hydrogen production.
- Open Access
- 18 February 2025
- Published by Springer Nature in Journal of Superconductivity and Novel Magnetism
- Vol. 38 (2) , 1-8
X-Ray Computed Tomography Study of the Microstructure of Superconducting MgB2 Bulks
MgB2 is a promising candidate for commercial superconducting applications because, as grain boundaries in MgB2 are not weak links, there are fewer limitations on the choice of processing technique compared to high-temperature superconducting (HTS) cuprates. MgB2 bulks are usually manufactured by powder processing techniques followed by a sintering process. After sintering, the impurity phases such as MgO and MgB4 along with porosity are formed which strongly affect the superconducting properties mainly the macroscopic path for supercurrent in MgB2 bulks. Investigation of these microstructural features is essential to improve the superconducting properties of these bulks. In this work, high-resolution laboratory X-ray computed tomography (XCT) has been used to investigate the microstructure of MgB2 bulks in three dimensions. The volume fraction of defects and impurity phases along with the size distribution of pores have been studied using this advanced technique. A comparison has been made between the data extracted from conventional characterization techniques such as XRD and SEM and those obtained from the advanced XCT analysis.
- 18 February 2025
- Published by Springer Nature in Journal of Superconductivity and Novel Magnetism
- Vol. 38 (2) , 1-8
Open AccessX-Ray Computed Tomography Study of the Microstructure of Superconducting MgB2 Bulks
MgB2 is a promising candidate for commercial superconducting applications because, as grain boundaries in MgB2 are not weak links, there are fewer limitations on the choice of processing technique compared to high-temperature superconducting (HTS) cuprates. MgB2 bulks are usually manufactured by powder processing techniques followed by a sintering process. After sintering, the impurity phases such as MgO and MgB4 along with porosity are formed which strongly affect the superconducting properties mainly the macroscopic path for supercurrent in MgB2 bulks. Investigation of these microstructural features is essential to improve the superconducting properties of these bulks. In this work, high-resolution laboratory X-ray computed tomography (XCT) has been used to investigate the microstructure of MgB2 bulks in three dimensions. The volume fraction of defects and impurity phases along with the size distribution of pores have been studied using this advanced technique. A comparison has been made between the data extracted from conventional characterization techniques such as XRD and SEM and those obtained from the advanced XCT analysis.
- 19 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (4) , 1-4
Comparison of the Microstructure and Superconducting Properties of Eu–Ba–Cu–O and Gd–Ba–Cu–O Single Grain Samples
Bulk Rare Earth–Ba–Cuprate [(RE)BCO] superconductors fabricated in the form of large single grains consisting of a REBa 2 Cu 3 O 7- δ (RE-123) matrix and RE 2 BaCuO 5 (RE-211) inclusions can generate trapped magnetic fields that are up to ten times higher than the maximum fields obtainable in conventional Fe-based permanent magnets. The choice of the Rare Earth (RE) element plays a key role in determining the growth rate of single grains, the precise microstructure, mechanical properties and hence the final superconducting properties of the bulk samples, and also the likelihood of RE substitution onto the Ba site which can degrade the performance. In this work, we have studied the growth and microstructure of (RE)BCO single grains with RE = Gd and Eu, where the degree of Ba substitution is known to be very different. We have carried out detailed microstructural characterization of the phase distribution and composition using high resolution electron microscopy to understand the effects of Gd and Eu on the uniformity of the samples, the distribution of the secondary 211 phase, porosity and chemical variations in different regions of the melt-grown single grains.
- 19 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (4) , 1-4
Comparison of the Microstructure and Superconducting Properties of Eu–Ba–Cu–O and Gd–Ba–Cu–O Single Grain Samples
Bulk Rare Earth–Ba–Cuprate [(RE)BCO] superconductors fabricated in the form of large single grains consisting of a REBa 2 Cu 3 O 7- δ (RE-123) matrix and RE 2 BaCuO 5 (RE-211) inclusions can generate trapped magnetic fields that are up to ten times higher than the maximum fields obtainable in conventional Fe-based permanent magnets. The choice of the Rare Earth (RE) element plays a key role in determining the growth rate of single grains, the precise microstructure, mechanical properties and hence the final superconducting properties of the bulk samples, and also the likelihood of RE substitution onto the Ba site which can degrade the performance. In this work, we have studied the growth and microstructure of (RE)BCO single grains with RE = Gd and Eu, where the degree of Ba substitution is known to be very different. We have carried out detailed microstructural characterization of the phase distribution and composition using high resolution electron microscopy to understand the effects of Gd and Eu on the uniformity of the samples, the distribution of the secondary 211 phase, porosity and chemical variations in different regions of the melt-grown single grains.
- 22 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 28 (4) , 1-3
Development of Superconducting Soldered Joints Between Bi-2212/Ag Wires
Bi-2212/Ag superconducting wires are being considered as key conductor candidates for the development of high field magnets (up to 25 T), but it is recognised that a reliable joining process between these wires is a critical challenge for most high-field applications. This work focuses on the design and testing of jointing processes between multifila-mentary Bi-2212 wires to make persistent mode joints using soldering techniques. The ability of several different su-perconducting solder alloys from the PbBi and SnInBi sys-tems to remove and replace the Ag matrix in fully reacted Bi-2212 wires has been explored. The SnInBi lead-free sol-der was found to be relatively effective at removing the Ag matrix, but does not make good contact with the Bi-2212 filaments. PbBi solder wets the Bi-2212 filaments more ef-fectively, but is slower at removing the Ag matrix. There-fore, a two-stage process has been developed using molten Sn to first remove the Ag matrix followed by PbBi to re-place the non-superconducting Sn. Joints made using this two-stage process have higher critical currents (133 A in self-field and 4 K) than joints made using PbBi alone (120 A in self-field 4K).
- 22 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 28 (4) , 1-3
Development of Superconducting Soldered Joints Between Bi-2212/Ag Wires
Bi-2212/Ag superconducting wires are being considered as key conductor candidates for the development of high field magnets (up to 25 T), but it is recognised that a reliable joining process between these wires is a critical challenge for most high-field applications. This work focuses on the design and testing of jointing processes between multifila-mentary Bi-2212 wires to make persistent mode joints using soldering techniques. The ability of several different su-perconducting solder alloys from the PbBi and SnInBi sys-tems to remove and replace the Ag matrix in fully reacted Bi-2212 wires has been explored. The SnInBi lead-free sol-der was found to be relatively effective at removing the Ag matrix, but does not make good contact with the Bi-2212 filaments. PbBi solder wets the Bi-2212 filaments more ef-fectively, but is slower at removing the Ag matrix. There-fore, a two-stage process has been developed using molten Sn to first remove the Ag matrix followed by PbBi to re-place the non-superconducting Sn. Joints made using this two-stage process have higher critical currents (133 A in self-field and 4 K) than joints made using PbBi alone (120 A in self-field 4K).