P. M. Mignanelli
Research Subjects
P. M. Mignanelli has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Howard James Stone
University of Cambridge
4 shared publications M. C. Hardy
3 shared publicationsN.G. Jones
3 shared publications- Katerina A. Christofidou
University of Sheffield
2 shared publications M.C. Hardy
2 shared publicationsN. G. Jones
Department of Materials Science and Metallurgy, Cambridge, UK
2 shared publications
Latest Publications
- Open Access
Effect of alloying on the microstructure, phase stability, hardness and partitioning behavior of a new dual-superlattice nickel-based superalloy
A novel y-y'-y" dual-superlattice superalloy, with promising mechanical properties up to elevated temperatures was recently reported. The present work employs state of the art chemical and spatial characterization techniques to study the effect systematic additions of Mo, W and Fe and variations in Nb and Al contents have on the phase fraction, thermal stability, elemental partitioning and mechanical properties. Alloys were produced through arc melting followed by heat treatment. Multi-scale characterization techniques and hardness testing were employed to characterize their microstructure, thermal stability and mechanical properties. Alterations in such properties or in elemental partitioning behaviour were then explained through thermodynamic modelling. A modest addition of 1.8 at.% Mo had a strong effect on the microstructure and thermal stability: it minimized microstructural coarsening during heat treatments while not significantly decreasing the y' solvus temperature. A reduction of Nb by 0.6 at.%, strongly reduced the y" volume fraction, without affecting the y' volume fraction. The reduced precipitate fraction led to a significant reduction in alloy hardness. Fe, added to achieve better processability and reduced material cost, decreased the y' solvus temperature and caused rapid microstructural coarsening during heat treatments, without affecting alloy hardness. A reduction of Al by 0.4 at.%, reduced the y' volume fraction and the y' solvus temperature, also without affecting alloy hardness. The addition of 0.9 at.% W decreased the y' solvus temperature but increased both precipitate volume fractions. These data will be invaluable to optimize current alloy design and to inform future alloy design efforts.
Open AccessEffect of alloying on the microstructure, phase stability, hardness and partitioning behavior of a new dual-superlattice nickel-based superalloy
A novel y-y'-y" dual-superlattice superalloy, with promising mechanical properties up to elevated temperatures was recently reported. The present work employs state of the art chemical and spatial characterization techniques to study the effect systematic additions of Mo, W and Fe and variations in Nb and Al contents have on the phase fraction, thermal stability, elemental partitioning and mechanical properties. Alloys were produced through arc melting followed by heat treatment. Multi-scale characterization techniques and hardness testing were employed to characterize their microstructure, thermal stability and mechanical properties. Alterations in such properties or in elemental partitioning behaviour were then explained through thermodynamic modelling. A modest addition of 1.8 at.% Mo had a strong effect on the microstructure and thermal stability: it minimized microstructural coarsening during heat treatments while not significantly decreasing the y' solvus temperature. A reduction of Nb by 0.6 at.%, strongly reduced the y" volume fraction, without affecting the y' volume fraction. The reduced precipitate fraction led to a significant reduction in alloy hardness. Fe, added to achieve better processability and reduced material cost, decreased the y' solvus temperature and caused rapid microstructural coarsening during heat treatments, without affecting alloy hardness. A reduction of Al by 0.4 at.%, reduced the y' volume fraction and the y' solvus temperature, also without affecting alloy hardness. The addition of 0.9 at.% W decreased the y' solvus temperature but increased both precipitate volume fractions. These data will be invaluable to optimize current alloy design and to inform future alloy design efforts.
- Open Access
- 5 October 2017
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 49 (3) , 699-707
On the Time-Temperature-Transformation Behavior of a New Dual-Superlattice Nickel-Based Superalloy
Recent research has identified compositions of nickel-based superalloys with microstructures containing appreciable and comparable volume fractions ofγ′ andγ″ precipitates. In this work, an alloy capable of forming such a dual-superlattice microstructure was subjected to a range of thermal exposures between 873 K and 1173 K (600 °C and 900 °C) for durations of 1 to 1000 hours. The microstructures and nature of the precipitating phases were characterized using synchrotron X-ray diffraction and electron microscopy. These data have enabled the construction of a T-T-T diagram for the precipitating phases. Hardness measurements following each thermal exposure have identified the age-hardening behavior of this alloy and allowed preliminary mechanical properties to be assessed.
- 5 October 2017
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 49 (3) , 699-707
Open AccessOn the Time-Temperature-Transformation Behavior of a New Dual-Superlattice Nickel-Based Superalloy
Recent research has identified compositions of nickel-based superalloys with microstructures containing appreciable and comparable volume fractions ofγ′ andγ″ precipitates. In this work, an alloy capable of forming such a dual-superlattice microstructure was subjected to a range of thermal exposures between 873 K and 1173 K (600 °C and 900 °C) for durations of 1 to 1000 hours. The microstructures and nature of the precipitating phases were characterized using synchrotron X-ray diffraction and electron microscopy. These data have enabled the construction of a T-T-T diagram for the precipitating phases. Hardness measurements following each thermal exposure have identified the age-hardening behavior of this alloy and allowed preliminary mechanical properties to be assessed.
- Open Access
- 1 April 2016
- Published by Elsevier in Intermetallics
- Vol. 71, 43-50
Phase evolution in an Al0.5CrFeCoNiCu High Entropy Alloy
- 1 April 2016
- Published by Elsevier in Intermetallics
- Vol. 71, 43-50
Open AccessPhase evolution in an Al0.5CrFeCoNiCu High Entropy Alloy
- Open Access
- 1 January 2015
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 621, 265-271
Microstructural evolution of a delta containing nickel-base superalloy during heat treatment and isothermal forging
- 1 January 2015
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 621, 265-271
Open AccessMicrostructural evolution of a delta containing nickel-base superalloy during heat treatment and isothermal forging
- 1 December 2014
- Published by SAGE Publications in Materials Science and Technology
- Vol. 30 (15) , 1853-1861
Influence of elevated Co and Ti levels on polycrystalline powder processed Ni-base superalloy
The influences of elevated Co and Ti levels on the mechanical properties of the Ni-base superalloy RR1000 have been investigated. Following heat treatment, the modified alloys had the typical γ–γ′ microstructure, with γ′ precipitate sizes comparable to similarly heat treated RR1000, but with a slightly higher volume fraction. The modified alloys exhibited a higher proof stress than RR1000 across the entire 20 to 800°C temperature range investigated. Superior creep rupture lives, when compared to RR1000, were observed in the modified alloys at 700°C, but not at 750°C, where extensive precipitation of topologically close packed σ phase occurred on the grain surfaces. The formation of this deleterious phase was linked to Cr and Mo enrichment of the γ matrix, caused by the elevated Co and Ti additions.
- 1 December 2014
- Published by SAGE Publications in Materials Science and Technology
- Vol. 30 (15) , 1853-1861
Influence of elevated Co and Ti levels on polycrystalline powder processed Ni-base superalloy
The influences of elevated Co and Ti levels on the mechanical properties of the Ni-base superalloy RR1000 have been investigated. Following heat treatment, the modified alloys had the typical γ–γ′ microstructure, with γ′ precipitate sizes comparable to similarly heat treated RR1000, but with a slightly higher volume fraction. The modified alloys exhibited a higher proof stress than RR1000 across the entire 20 to 800°C temperature range investigated. Superior creep rupture lives, when compared to RR1000, were observed in the modified alloys at 700°C, but not at 750°C, where extensive precipitation of topologically close packed σ phase occurred on the grain surfaces. The formation of this deleterious phase was linked to Cr and Mo enrichment of the γ matrix, caused by the elevated Co and Ti additions.
- Open Access
- 1 August 2014
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 612, 179-186
The influence of Al:Nb ratio on the microstructure and mechanical response of quaternary Ni–Cr–Al–Nb alloys
- 1 August 2014
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 612, 179-186
Open AccessThe influence of Al:Nb ratio on the microstructure and mechanical response of quaternary Ni–Cr–Al–Nb alloys