Maria José Santos Lima
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Maria José Santos Lima has a total of 60 co-authors. Here are the top co-authors by number of shared publications:
- Cleber da Silva Lourenço
Department of Physics, Federal University of Rio Grande do Norte, Natal 59078-970, RN, Brazil
8 shared publications - Kivia Fabiana Galvão Araújo
Graduate Program in Materials Science and Engineering, Federal University of Rio Grande do Norte, Natal 59078-970, RN, Brazil
8 shared publications - Uilame Umbelino Gomes
Graduate Program in Materials Science and Engineering, Federal University of Rio Grande do Norte, Natal 59078-970, RN, Brazil
8 shared publications - Marco Antonio Morales Torres
Facultad de Ciencias, Universidad Nacional de Ingeniería, Av. Túpac Amaru 210, Lima 15333, Peru
5 shared publications - Fernando E. S. Silva
Graduate Program in Chemical Engineering, Federal University of Rio Grande do Norte, Natal 59078-970, RN, Brazil
4 shared publications - Gabriel S. Vasconcelos
Graduate Program in Materials Science and Engineering, Federal University of Rio Grande do Norte, Natal 59078-970, RN, Brazil
3 shared publications
Latest Publications
- Open Access
Synthesis of Nanostructured Tungsten-Based Catalyst from Scheelite Ore for Electrocatalytic Oxygen Evolution Reaction
This study presents an integrated low-temperature processing route that converts tungstic acid and ammonium paratungstate derived from scheelite ore (CaWO4) into nanoscale tungsten trioxide (WO3), metallic tungsten (W), and tungsten carbide (WC) via solid-state reaction, hydrogen reduction, and gas–solid reaction, respectively. This approach enables particle size control, reduced energy consumption, and enhanced functional properties, enabling evaluation of the materials’ performance in the oxygen evolution reaction (OER). X-ray diffraction (XRD) confirmed the formation of the desired phases with nanocrystalline structures and average crystallite sizes of 13.3 nm (WO3), 31.55 nm (W), and 10.35 nm (WC). The materials exhibited homogeneous morphologies, demonstrating the effectiveness of the synthesis routes. Electrochemical measurements revealed promising OER activity; the WO3 electrode showed the lowest overpotential of 321 mV at 10 mA cm−2, while W and WC showed 327 mV and 340 mV, respectively, in 1.0 M KOH. Overall, the results demonstrate a strategy for scheelite valorization.
Open AccessSynthesis of Nanostructured Tungsten-Based Catalyst from Scheelite Ore for Electrocatalytic Oxygen Evolution Reaction
This study presents an integrated low-temperature processing route that converts tungstic acid and ammonium paratungstate derived from scheelite ore (CaWO4) into nanoscale tungsten trioxide (WO3), metallic tungsten (W), and tungsten carbide (WC) via solid-state reaction, hydrogen reduction, and gas–solid reaction, respectively. This approach enables particle size control, reduced energy consumption, and enhanced functional properties, enabling evaluation of the materials’ performance in the oxygen evolution reaction (OER). X-ray diffraction (XRD) confirmed the formation of the desired phases with nanocrystalline structures and average crystallite sizes of 13.3 nm (WO3), 31.55 nm (W), and 10.35 nm (WC). The materials exhibited homogeneous morphologies, demonstrating the effectiveness of the synthesis routes. Electrochemical measurements revealed promising OER activity; the WO3 electrode showed the lowest overpotential of 321 mV at 10 mA cm−2, while W and WC showed 327 mV and 340 mV, respectively, in 1.0 M KOH. Overall, the results demonstrate a strategy for scheelite valorization.
- Open Access
Ammonium Paratungstate Production from Scheelite Ore: Process Study, Morphology and Thermal Stability
Ammonium paratungstate (APT) was synthesized from scheelite ore concentrates from the Brejuí Mine in Currais Novos, Rio Grande do Norte, Northeast Brazil. The process involved acid leaching to obtain tungstic acid (H2WO4), followed by its conversion to APT. A 23 factorial design evaluated the influence of temperature, HCl concentration, and reaction time on the leaching efficiency, revealing temperature and acid concentration as significant variables. Tungsten extraction reached 98.6% under moderate time and temperature conditions. The resulting H2WO4 phase exhibited a lamellar and porous morphology, facilitating its rapid dissolution and crystallization into APT at 60 °C. The produced nanometric APT exhibited high purity, a mixed rod-like/cubic morphology, and thermal stability above 600 °C. This work adds value to the Brazilian tungsten deposits by supporting more efficient and sustainable extraction routes for obtaining APT.
Open AccessAmmonium Paratungstate Production from Scheelite Ore: Process Study, Morphology and Thermal Stability
Ammonium paratungstate (APT) was synthesized from scheelite ore concentrates from the Brejuí Mine in Currais Novos, Rio Grande do Norte, Northeast Brazil. The process involved acid leaching to obtain tungstic acid (H2WO4), followed by its conversion to APT. A 23 factorial design evaluated the influence of temperature, HCl concentration, and reaction time on the leaching efficiency, revealing temperature and acid concentration as significant variables. Tungsten extraction reached 98.6% under moderate time and temperature conditions. The resulting H2WO4 phase exhibited a lamellar and porous morphology, facilitating its rapid dissolution and crystallization into APT at 60 °C. The produced nanometric APT exhibited high purity, a mixed rod-like/cubic morphology, and thermal stability above 600 °C. This work adds value to the Brazilian tungsten deposits by supporting more efficient and sustainable extraction routes for obtaining APT.
- Open Access
- 28 October 2025
- Published by MDPI AG in Magnetochemistry
- Vol. 11 (11) , 94
Synthesis, Structural, and Magnetic Properties of High-Entropy (Fe0.2Co0.2Cu0.2Ni0.2Mn0.2)Nb2O6
In this work, we present the first report on the synthesis via the sol–gel method of a high-entropy (Fe0.2Co0.2Cu0.2Ni0.2Mn0.2)Nb2O6 with columbite–orthorhombic structure. Polyvinylpyrrolidone (PVP), ammonium niobium oxalate, and equimolar amounts of Fe, Co, Cu, Ni, and Mn ions were used. The refinement of the XRD pattern showed the presence of niobate crystallites with an average size of 48.4 nm and a fraction of 7.6 wt% of a spinel-like phase. At temperatures below 5 K, the DC and AC magnetometry results revealed the presence of a ferromagnetic-like phase due to the niobate phase. The Mössbauer spectrum at 300 K showed a paramagnetic and two magnetically ordered components corresponding to the niobate and the spinel-like phases, respectively. The spectral components were typical of Fe3+, indicating the presence of cation vacancies. The elemental mapping obtained from EDS measurements showed compositional homogeneity. The XRF measurements confirmed a composition consistent with nominal values. These results confirm the feasibility of synthesizing entropy-stabilized columbite oxides via the sol–gel route, opening new opportunities for the design of multifunctional ceramics with tunable structural and magnetic properties for high-performance thermal barrier coatings and energy conversion applications.
- 28 October 2025
- Published by MDPI AG in Magnetochemistry
- Vol. 11 (11) , 94
Open AccessSynthesis, Structural, and Magnetic Properties of High-Entropy (Fe0.2Co0.2Cu0.2Ni0.2Mn0.2)Nb2O6
In this work, we present the first report on the synthesis via the sol–gel method of a high-entropy (Fe0.2Co0.2Cu0.2Ni0.2Mn0.2)Nb2O6 with columbite–orthorhombic structure. Polyvinylpyrrolidone (PVP), ammonium niobium oxalate, and equimolar amounts of Fe, Co, Cu, Ni, and Mn ions were used. The refinement of the XRD pattern showed the presence of niobate crystallites with an average size of 48.4 nm and a fraction of 7.6 wt% of a spinel-like phase. At temperatures below 5 K, the DC and AC magnetometry results revealed the presence of a ferromagnetic-like phase due to the niobate phase. The Mössbauer spectrum at 300 K showed a paramagnetic and two magnetically ordered components corresponding to the niobate and the spinel-like phases, respectively. The spectral components were typical of Fe3+, indicating the presence of cation vacancies. The elemental mapping obtained from EDS measurements showed compositional homogeneity. The XRF measurements confirmed a composition consistent with nominal values. These results confirm the feasibility of synthesizing entropy-stabilized columbite oxides via the sol–gel route, opening new opportunities for the design of multifunctional ceramics with tunable structural and magnetic properties for high-performance thermal barrier coatings and energy conversion applications.
- Open Access
CuNb2O6 Particles Obtained via Solid-State Reaction and Application as Electrocatalyst for Oxygen Evolution Reaction
Copper niobate (CuNb2O6) is an important compound due to its low cost and polymorphism, presenting monoclinic and orthorhombic phases, which leads to unique physical–chemical properties. The electrochemical performance of efficient electrocatalysts for the oxygen evolution reaction (OER) is of importance in order to produce hydrogen gas from water. In this context, this work reports the synthesis of CuNb2O6 particles by high-energy milling for 5 and 10 h, and subsequent thermal treatment at 900 °C for 3 h. The samples were characterized by XRD, XRF, FESEM, RAMAN, UV–Vis, and FT-IR techniques, and were applied as electrocatalysts for the OER. The samples had both monoclinic and orthorhombic crystalline phases. The band gaps were in the range of 1.92 to 2.06 eV. In the application for the OER, the particles obtained by 5 and 10 h of milling exhibited overpotentials of 476 and 347 mV vs. RHE at 10 mA cm−2, respectively. In chronopotentiometry experiments for 15 h, the samples exhibited excellent chemical stability. The electrochemical performance of the sample milled for 10 h showed superior performance (347 mV vs. RHE) when compared with electrocatalysts of the same type, demonstrating that the methodology used to synthesize the samples is promising for energy applications.
Open AccessCuNb2O6 Particles Obtained via Solid-State Reaction and Application as Electrocatalyst for Oxygen Evolution Reaction
Copper niobate (CuNb2O6) is an important compound due to its low cost and polymorphism, presenting monoclinic and orthorhombic phases, which leads to unique physical–chemical properties. The electrochemical performance of efficient electrocatalysts for the oxygen evolution reaction (OER) is of importance in order to produce hydrogen gas from water. In this context, this work reports the synthesis of CuNb2O6 particles by high-energy milling for 5 and 10 h, and subsequent thermal treatment at 900 °C for 3 h. The samples were characterized by XRD, XRF, FESEM, RAMAN, UV–Vis, and FT-IR techniques, and were applied as electrocatalysts for the OER. The samples had both monoclinic and orthorhombic crystalline phases. The band gaps were in the range of 1.92 to 2.06 eV. In the application for the OER, the particles obtained by 5 and 10 h of milling exhibited overpotentials of 476 and 347 mV vs. RHE at 10 mA cm−2, respectively. In chronopotentiometry experiments for 15 h, the samples exhibited excellent chemical stability. The electrochemical performance of the sample milled for 10 h showed superior performance (347 mV vs. RHE) when compared with electrocatalysts of the same type, demonstrating that the methodology used to synthesize the samples is promising for energy applications.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1)
Synthesis and Characterization of Nanostructured Molybdenum Carbide through Low Temperature Gas-Solid Reaction
This work used ammonium heptamolybdate as a precursor to obtain molybdenum carbide (Mo2C) at temperatures of 600°C, 650°C and 700°C, using isotherms of 60 min, 90 min and 120 min. The samples were characterized by thermogravimetric (TG), X-ray diffraction (XRD), Rietveld refinement and scanning electron microscopy (SEM). The results revealed that Mo2C formation was strongly dependent on the source temperature and isotherm duration. Characteristic diffraction peaks of molybdenum carbide were identified in samples synthesized at 700 °C for 60 minutes and 120 minutes, indicating that this temperature was crucial for demonstrating complete carburization under the tested conditions. Conversely, samples processed at lower temperatures showed incomplete reactions, with precursor phases and residual byproducts, indicating the need for greater energy transport and reaction time to promote complete transformation into pure Mo2C. These results reinforce the importance of simultaneously optimizing temperature and isotherm parameters to tailor the phase purity and microstructural properties of molybdenum carbide for advanced applications.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1)
Open AccessSynthesis and Characterization of Nanostructured Molybdenum Carbide through Low Temperature Gas-Solid Reaction
This work used ammonium heptamolybdate as a precursor to obtain molybdenum carbide (Mo2C) at temperatures of 600°C, 650°C and 700°C, using isotherms of 60 min, 90 min and 120 min. The samples were characterized by thermogravimetric (TG), X-ray diffraction (XRD), Rietveld refinement and scanning electron microscopy (SEM). The results revealed that Mo2C formation was strongly dependent on the source temperature and isotherm duration. Characteristic diffraction peaks of molybdenum carbide were identified in samples synthesized at 700 °C for 60 minutes and 120 minutes, indicating that this temperature was crucial for demonstrating complete carburization under the tested conditions. Conversely, samples processed at lower temperatures showed incomplete reactions, with precursor phases and residual byproducts, indicating the need for greater energy transport and reaction time to promote complete transformation into pure Mo2C. These results reinforce the importance of simultaneously optimizing temperature and isotherm parameters to tailor the phase purity and microstructural properties of molybdenum carbide for advanced applications.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28
The Influence of Thermal Processing with H2 Atmosphere on the Physical Properties and Microstructure for use in Electrolytic Capacitors of Nb
This study evaluated the effect of thermal processing in hydrogen (H2) and argon (Ar) atmospheres on the physical and microstructural properties of niobium (Nb) powders for electrolytic capacitors. Nb powders were treated at 750 °C, 850 °C and 950 °C with isothermal holds of 60 min and 120 min—samples H2-850-120 and Ar-850-120 denote the H2 and Ar atmospheres—using a heating rate of 10 °C/min. Powders were compacted at 150 MPa and sintered at 1200 °C under H2. XRD confirmed predominant βH phase and minor NbO in H2-treated powders, while Ar-treated samples exhibited stronger NbO reflections. FEG-SEM micrographs showed finer grains and reduced porosity in H2-850-120. These results demonstrate that hydrogen-atmosphere processing yields Nb powders with improved homogeneity, particle size reduction and densification—key attributes for enhanced capacitor performance.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28
Open AccessThe Influence of Thermal Processing with H2 Atmosphere on the Physical Properties and Microstructure for use in Electrolytic Capacitors of Nb
This study evaluated the effect of thermal processing in hydrogen (H2) and argon (Ar) atmospheres on the physical and microstructural properties of niobium (Nb) powders for electrolytic capacitors. Nb powders were treated at 750 °C, 850 °C and 950 °C with isothermal holds of 60 min and 120 min—samples H2-850-120 and Ar-850-120 denote the H2 and Ar atmospheres—using a heating rate of 10 °C/min. Powders were compacted at 150 MPa and sintered at 1200 °C under H2. XRD confirmed predominant βH phase and minor NbO in H2-treated powders, while Ar-treated samples exhibited stronger NbO reflections. FEG-SEM micrographs showed finer grains and reduced porosity in H2-850-120. These results demonstrate that hydrogen-atmosphere processing yields Nb powders with improved homogeneity, particle size reduction and densification—key attributes for enhanced capacitor performance.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1)
Analysis of Sintering Curves, Microstructure, and Microhardness of the Cu-WC Composite
Composite materials have gained prominence due to their tailored properties for various applications. Cu-WC composites, combining a copper matrix with tungsten carbide reinforcement, are particularly valuable for electrical conductors and heat sinks. This study examined the sintering behavior of Cu-WC composite powder (10%WC) produced via High-Energy Ball Milling (HEBM) at 400 RPM for 2, 10, and 20 hours. The powders were compacted at 150 MPa and sintered at 900°C with a 1-hour isothermal hold. Sintering curves, microstructure, and Vickers microhardness were analyzed. The results showed that longer milling times led to significant powder expansion up to 750°C, followed by greater shrinkage due to diffusion mechanisms. Sintered samples milled for 10 hours displayed improved carbide distribution in the copper matrix. The highest microhardness was achieved at 20 hours of milling, attributed to refined microstructure. Extended milling times enhanced atomic diffusion during sintering, resulting in a more homogeneous structure and increased hardness.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1)
Open AccessAnalysis of Sintering Curves, Microstructure, and Microhardness of the Cu-WC Composite
Composite materials have gained prominence due to their tailored properties for various applications. Cu-WC composites, combining a copper matrix with tungsten carbide reinforcement, are particularly valuable for electrical conductors and heat sinks. This study examined the sintering behavior of Cu-WC composite powder (10%WC) produced via High-Energy Ball Milling (HEBM) at 400 RPM for 2, 10, and 20 hours. The powders were compacted at 150 MPa and sintered at 900°C with a 1-hour isothermal hold. Sintering curves, microstructure, and Vickers microhardness were analyzed. The results showed that longer milling times led to significant powder expansion up to 750°C, followed by greater shrinkage due to diffusion mechanisms. Sintered samples milled for 10 hours displayed improved carbide distribution in the copper matrix. The highest microhardness was achieved at 20 hours of milling, attributed to refined microstructure. Extended milling times enhanced atomic diffusion during sintering, resulting in a more homogeneous structure and increased hardness.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1)
Development of a Method for the Synthesis of Ammoniacal Niobium Oxalate Trihydrate for Use as a Precursor in Chemical Reactions
In this project, a method was developed to synthesize ammoniacal niobium oxalate (NH4)(NbO(C2O4)(H2O)ᵧ)·XH2O, aimed at its application in the preparation of niobium-incorporated materials. This transition metal exhibits excellent properties and is widely available in Brazil. Its versatility makes it essential for metal alloys and electronic components. The synthesis was based on physical and chemical processes, including fusion, decantation, filtration, and complexation, using niobium pentoxide and potassium bisulfate. Rigorous procedures were implemented to ensure precursor quality. Material characterization was performed using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and thermogravimetric analysis (TGA), which collectively confirmed the material's morphology, structure, and thermal stability. The results confirmed the efficient synthesis of high-purity niobium oxalate, with the developed method demonstrating technical feasibility by preserving the material's essential physicochemical properties, as verified by the characterization techniques. Key innovations included replacing acid leaching with a more efficient method, implementing neutral-pH decantation instead of traditional acidic processes, and the strategic use of an aqueous acetic acid solution in the washing step. This combination of advancements enabled a 75% reduction in water consumption during the washing stage, thus establishing a significantly more sustainable synthesis protocol for producing this precursor without compromising final product quality.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1)
Open AccessDevelopment of a Method for the Synthesis of Ammoniacal Niobium Oxalate Trihydrate for Use as a Precursor in Chemical Reactions
In this project, a method was developed to synthesize ammoniacal niobium oxalate (NH4)(NbO(C2O4)(H2O)ᵧ)·XH2O, aimed at its application in the preparation of niobium-incorporated materials. This transition metal exhibits excellent properties and is widely available in Brazil. Its versatility makes it essential for metal alloys and electronic components. The synthesis was based on physical and chemical processes, including fusion, decantation, filtration, and complexation, using niobium pentoxide and potassium bisulfate. Rigorous procedures were implemented to ensure precursor quality. Material characterization was performed using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and thermogravimetric analysis (TGA), which collectively confirmed the material's morphology, structure, and thermal stability. The results confirmed the efficient synthesis of high-purity niobium oxalate, with the developed method demonstrating technical feasibility by preserving the material's essential physicochemical properties, as verified by the characterization techniques. Key innovations included replacing acid leaching with a more efficient method, implementing neutral-pH decantation instead of traditional acidic processes, and the strategic use of an aqueous acetic acid solution in the washing step. This combination of advancements enabled a 75% reduction in water consumption during the washing stage, thus establishing a significantly more sustainable synthesis protocol for producing this precursor without compromising final product quality.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1) , e20250279
Influence of Temperature on the APT Carborreduction Process for Obtaining Nanocrystalline WC Powder from Sheelite Concentrate
Tungsten carbide (WC) is a highly relevant material due to its exceptional catalytic properties and applications in composite materials and cutting tools. The production of nanocrystalline and ultrafine WC powders contributes to enhanced properties in these applications. Therefore, this study aims to obtain nanocrystalline WC powders with a high surface area from ammonium paratungstate (APT) derived from scheelite concentrate. To achieve this, a gas-solid reaction (carbothermal reduction) of APT was carried out at different temperatures under a mixed H2/CH4 atmosphere. The results showed that the WC powders obtained at 850°C present a higher purity with a crystallite size of 15.8 nm composed of agglomerates of ultrafine particles of 159 μm.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1) , e20250279
Open AccessInfluence of Temperature on the APT Carborreduction Process for Obtaining Nanocrystalline WC Powder from Sheelite Concentrate
Tungsten carbide (WC) is a highly relevant material due to its exceptional catalytic properties and applications in composite materials and cutting tools. The production of nanocrystalline and ultrafine WC powders contributes to enhanced properties in these applications. Therefore, this study aims to obtain nanocrystalline WC powders with a high surface area from ammonium paratungstate (APT) derived from scheelite concentrate. To achieve this, a gas-solid reaction (carbothermal reduction) of APT was carried out at different temperatures under a mixed H2/CH4 atmosphere. The results showed that the WC powders obtained at 850°C present a higher purity with a crystallite size of 15.8 nm composed of agglomerates of ultrafine particles of 159 μm.
- 10 September 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (22) , 47445-47455
Enhanced properties of hard metal WC-Ni processed from nanostructured powders
- 10 September 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (22) , 47445-47455
Enhanced properties of hard metal WC-Ni processed from nanostructured powders