Shaken Kenzhekhanov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Shaken Kenzhekhanov has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
Kai He
Halliburton
3 shared publicationsLiang Xu
Halliburton
3 shared publicationsXiaolong Yin
Colorado School of Mines
3 shared publicationsINSTITUTE OF GEOLOGICAL SCIENCES NAMED AFTER K.I. SATPAEV
2 shared publications- Iskander Gussenov
Institute of Polymer Materials and Technology, Almaty 050019, Kazakhstan
2 shared publications Keith Neeves
Colorado School of Mines
2 shared publications
Latest Publications
- 15 December 2023
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 138 (6) , 101-110
SODIUM SILICATE GELS FOR WATER SHUT-OFF IN OIL RESERVOIRS
This work is dedicated to the problem of reducing the permeability of oil reservoirs to water. An experimental study was conducted, the results of which show that the gel based on liquid glass and hydrochloric acid is partially washed out from the model of water flooded oil reservoir under a pressure gradient of approximately 14 MPa/m, which in practice will lead to a decrease in efficiency. However, adding laponite nano-clay to the solution of liquid glass and hydrochloric acid allows solving this problem and achieving a 400-fold reduction in the permeability of the model of water flooded oil reservoir at a pressure gradient of approximately 33 MPa/m. This result can be explained by the fact that adding laponite to the solution of liquid glass and hydrochloric acid leads to an increase in the mechanical strength of the gel. For example, adding 1% laponite to the solution of liquid glass and hydrochloric acid increased the Young’s modulus from 550 to 1280 Pa. The results of this work demonstrate the potential application of liquid glass gels with fillers to increase the efficiency of plugging agents in operations to reduce water production in oil wells. Future research will focus on conducting filtration experiments on fractured models.
- 15 December 2023
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 138 (6) , 101-110
SODIUM SILICATE GELS FOR WATER SHUT-OFF IN OIL RESERVOIRS
This work is dedicated to the problem of reducing the permeability of oil reservoirs to water. An experimental study was conducted, the results of which show that the gel based on liquid glass and hydrochloric acid is partially washed out from the model of water flooded oil reservoir under a pressure gradient of approximately 14 MPa/m, which in practice will lead to a decrease in efficiency. However, adding laponite nano-clay to the solution of liquid glass and hydrochloric acid allows solving this problem and achieving a 400-fold reduction in the permeability of the model of water flooded oil reservoir at a pressure gradient of approximately 33 MPa/m. This result can be explained by the fact that adding laponite to the solution of liquid glass and hydrochloric acid leads to an increase in the mechanical strength of the gel. For example, adding 1% laponite to the solution of liquid glass and hydrochloric acid increased the Young’s modulus from 550 to 1280 Pa. The results of this work demonstrate the potential application of liquid glass gels with fillers to increase the efficiency of plugging agents in operations to reduce water production in oil wells. Future research will focus on conducting filtration experiments on fractured models.
- 9 October 2017
- Published by Society of Petroleum Engineers (SPE)
Rock-On-A-Chip Approach Provides New Insight for Well Interferences in Liquids-Rich Shale Plays
As infill drilling practices become more widely used, operators have observed increased well interference or "bashing" in various shale plays wherein the production of mature wells has been significantly impaired by new infilling wells. Notably, some wells have experienced production decrease of approximately 80% as a result of bashing. One possible explanation is the occurrence of hydraulic communication between the old and new wells because they are most likely connected by the newly created or reactivated natural fractures. However, the mechanisms in which hydraulic communication influences production have not been fundamentally studied.Current technologies, such as pressure-transient analysis or production data mining, do not explicitly provide a physical understanding of the bashing phenomena. This paper discusses a study wherein "Rock-on-a-chip" (ROC) devices were used to investigate hydraulic fracturing fluid invasion and flowback processes. A homogeneous porous network based on the Voronoi tessellation method was patterned on a ROC device. To simulate one aspect of well interference (the impact of an offset well's fracturing fluid entering an existing well's fracture network), two fluid invasion-flowback cycles were performed. It was hypothesized that if the fracturing fluid injected through the new infill enters the fracture networks of existing wells, fracturing fluid would again be forced into the matrix, inflicting damage to the fracture-matrix interface and impairing production.Test results revealed that water saturations in the ROC after the second flowback were higher than those after the first invasion-flowback cycle, suggesting that the second invasion-flowback cycle could indeed damage the matrix and reduce the relative permeability of the oil. Additionally, surfactant clearly improved the displacement efficiencies in the matrix. One experiment shows that surfactant used in the second invasion-flowback cycle even reduced the damage incurred by the first invasion-flowback cycle. The benefit of surfactant has been observed from field results from the Wolfcamp shale, where it was discovered that the EURs (estimated ultimate recoverys) of wells bashed by surfactant-stimulated offset wells were higher than those bashed by non-surfactant-stimulated offset wells. This study shows that fracturing fluid from offset wells can, in fact, damage the productivity of existing wells through connected fractures. In addition, surfactant, when properly selected, can potentially be used to help reduce damage, or even repair previous damage, caused by well bashing.
- 9 October 2017
- Published by Society of Petroleum Engineers (SPE)
Rock-On-A-Chip Approach Provides New Insight for Well Interferences in Liquids-Rich Shale Plays
As infill drilling practices become more widely used, operators have observed increased well interference or "bashing" in various shale plays wherein the production of mature wells has been significantly impaired by new infilling wells. Notably, some wells have experienced production decrease of approximately 80% as a result of bashing. One possible explanation is the occurrence of hydraulic communication between the old and new wells because they are most likely connected by the newly created or reactivated natural fractures. However, the mechanisms in which hydraulic communication influences production have not been fundamentally studied.Current technologies, such as pressure-transient analysis or production data mining, do not explicitly provide a physical understanding of the bashing phenomena. This paper discusses a study wherein "Rock-on-a-chip" (ROC) devices were used to investigate hydraulic fracturing fluid invasion and flowback processes. A homogeneous porous network based on the Voronoi tessellation method was patterned on a ROC device. To simulate one aspect of well interference (the impact of an offset well's fracturing fluid entering an existing well's fracture network), two fluid invasion-flowback cycles were performed. It was hypothesized that if the fracturing fluid injected through the new infill enters the fracture networks of existing wells, fracturing fluid would again be forced into the matrix, inflicting damage to the fracture-matrix interface and impairing production.Test results revealed that water saturations in the ROC after the second flowback were higher than those after the first invasion-flowback cycle, suggesting that the second invasion-flowback cycle could indeed damage the matrix and reduce the relative permeability of the oil. Additionally, surfactant clearly improved the displacement efficiencies in the matrix. One experiment shows that surfactant used in the second invasion-flowback cycle even reduced the damage incurred by the first invasion-flowback cycle. The benefit of surfactant has been observed from field results from the Wolfcamp shale, where it was discovered that the EURs (estimated ultimate recoverys) of wells bashed by surfactant-stimulated offset wells were higher than those bashed by non-surfactant-stimulated offset wells. This study shows that fracturing fluid from offset wells can, in fact, damage the productivity of existing wells through connected fractures. In addition, surfactant, when properly selected, can potentially be used to help reduce damage, or even repair previous damage, caused by well bashing.
- 12 June 2017
- Published by Society of Petroleum Engineers (SPE)
UNAVAILABLE - Rock-on-a-Chip ROC Approach Provides New Insights for Well Interferences in Liquid-Rich Shale Plays
As infill drilling practices become more widely used, operators have observed an increase in well interference or "bashing" in various shale plays in which the production of mature wells has been significantly impaired by new infilling wells. Notably, some wells have experienced a production decrease of approximately 80% as a result of bashing. One possible explanation is the occurrence of hydraulic communication between the old and new wells, as they are most likely connected by the newly created or natural fractures. However, the mechanisms in which hydraulic communication influences production have not been fundamentally studied. Current technologies, such as pressure-transient analysis or production data mining, do not explicitly provide a physical understanding of the bashing phenomena. In this study, "Rock-on-a-Chip" (ROC) devices were used to investigate hydraulic fracturing fluid invasion and flowback processes. A homogeneous porous network based on the Voronoi tessellation method was patterned on a ROC device. To simulate one aspect of well interference (the impact of an offset well's fracturing fluid entering an existing well's fracture network), two fluid invasion-flowback cycles were performed. It was hypothesized that if the fracturing fluid injected through the new infill enters the fracture networks of existing wells, fracturing fluid would again be forced into the matrix, inflicting damage to the fracture-matrix interface and impairing production. Test results revealed that water saturations in the ROC after the second flowback were higher than those after the first invasion-flowback cycle, suggesting that the second invasion-flowback cycle could indeed damage the matrix and reduce the relative permeability of the oil. Additionally, surfactant clearly improved the displacement efficiencies in the matrix and, therefore, has the potential to reduce the damage incurred by the second invasion-flowback cycle. The benefit of surfactant has been observed from field results from the Wolfcamp shale, where it was discovered that the EURs of wells bashed by surfactant-stimulated offset wells were higher than those bashed by non-surfactant-stimulated offset wells. This study shows that fracturing fluid from offset wells can, in fact, damage the productivity of existing wells through connected fractures. In addition, surfactant, when properly selected, can potentially be used to reduce the damage, or even repair previous damage, caused by well bashing.
- 12 June 2017
- Published by Society of Petroleum Engineers (SPE)
UNAVAILABLE - Rock-on-a-Chip ROC Approach Provides New Insights for Well Interferences in Liquid-Rich Shale Plays
As infill drilling practices become more widely used, operators have observed an increase in well interference or "bashing" in various shale plays in which the production of mature wells has been significantly impaired by new infilling wells. Notably, some wells have experienced a production decrease of approximately 80% as a result of bashing. One possible explanation is the occurrence of hydraulic communication between the old and new wells, as they are most likely connected by the newly created or natural fractures. However, the mechanisms in which hydraulic communication influences production have not been fundamentally studied. Current technologies, such as pressure-transient analysis or production data mining, do not explicitly provide a physical understanding of the bashing phenomena. In this study, "Rock-on-a-Chip" (ROC) devices were used to investigate hydraulic fracturing fluid invasion and flowback processes. A homogeneous porous network based on the Voronoi tessellation method was patterned on a ROC device. To simulate one aspect of well interference (the impact of an offset well's fracturing fluid entering an existing well's fracture network), two fluid invasion-flowback cycles were performed. It was hypothesized that if the fracturing fluid injected through the new infill enters the fracture networks of existing wells, fracturing fluid would again be forced into the matrix, inflicting damage to the fracture-matrix interface and impairing production. Test results revealed that water saturations in the ROC after the second flowback were higher than those after the first invasion-flowback cycle, suggesting that the second invasion-flowback cycle could indeed damage the matrix and reduce the relative permeability of the oil. Additionally, surfactant clearly improved the displacement efficiencies in the matrix and, therefore, has the potential to reduce the damage incurred by the second invasion-flowback cycle. The benefit of surfactant has been observed from field results from the Wolfcamp shale, where it was discovered that the EURs of wells bashed by surfactant-stimulated offset wells were higher than those bashed by non-surfactant-stimulated offset wells. This study shows that fracturing fluid from offset wells can, in fact, damage the productivity of existing wells through connected fractures. In addition, surfactant, when properly selected, can potentially be used to reduce the damage, or even repair previous damage, caused by well bashing.
- 27 March 2017
- Published by Society of Petroleum Engineers (SPE)
A Rock-on-a-Chip Approach to Study Fluid Invasion and Flowback in Liquids-Rich Shale Formations
Understanding the dynamic process of fluid invasion and flowback has significant technological implications in developing shale plays. One of the physical models used to study this process is coreflooding, which mimics the process of fracturing fluid invasion, flowback, and hydrocarbon recovery from shale formations. However, coreflooding is time consuming, expensive, and unable to provide insights to the underlying physics at the pore scale level in most instances. Rock-on-a Chip (ROC), based on microfluidic technology, is an emerging approach that provides a new method to study fracturing fluid invasion and flowback affected by the petrophysical properties using direct visualization and measurement. In this study, the porous matrix, representing shale formations, and single large channel, representing hydraulic fractures or natural fractures, were defined in an oil-wet microfluidic chip; the drainage-imbibition cycles that are analogous to fracturing fluid invasion and subsequent flowback were measured by optical microscopy. Specifically, the effect of interfacial tension and fracture patterns ("half" fracture and "S" fracture) on the fluid invasion factor and flowback efficiency was examined. The results show that the invasion factor and flowback efficiency correlated well with the capillary pressure of fracturing fluids. In addition, model fractures have a major effect on the flowback. In particular, the invasion factor and flowback efficiency of the water-based fracturing fluids were significantly impaired in the "S" fracture pattern, as compared to homogeneous and half fracture patterns. Notably, by improving fluid mobility between the porous matrix and fractures, the addition of a surfactant to the fracturing fluids significantly enhanced the fluid invasion and flowback in all of the fracture patterns. The results demonstrate that the ROC model proposed in this work can be used to study the flowback process affected by properties such as wettability, permeability, initial water saturation, and reservoir pressure. Consequently, it has potential for guiding water management and chemical treatment in hydraulic fracturing.
- 27 March 2017
- Published by Society of Petroleum Engineers (SPE)
A Rock-on-a-Chip Approach to Study Fluid Invasion and Flowback in Liquids-Rich Shale Formations
Understanding the dynamic process of fluid invasion and flowback has significant technological implications in developing shale plays. One of the physical models used to study this process is coreflooding, which mimics the process of fracturing fluid invasion, flowback, and hydrocarbon recovery from shale formations. However, coreflooding is time consuming, expensive, and unable to provide insights to the underlying physics at the pore scale level in most instances. Rock-on-a Chip (ROC), based on microfluidic technology, is an emerging approach that provides a new method to study fracturing fluid invasion and flowback affected by the petrophysical properties using direct visualization and measurement. In this study, the porous matrix, representing shale formations, and single large channel, representing hydraulic fractures or natural fractures, were defined in an oil-wet microfluidic chip; the drainage-imbibition cycles that are analogous to fracturing fluid invasion and subsequent flowback were measured by optical microscopy. Specifically, the effect of interfacial tension and fracture patterns ("half" fracture and "S" fracture) on the fluid invasion factor and flowback efficiency was examined. The results show that the invasion factor and flowback efficiency correlated well with the capillary pressure of fracturing fluids. In addition, model fractures have a major effect on the flowback. In particular, the invasion factor and flowback efficiency of the water-based fracturing fluids were significantly impaired in the "S" fracture pattern, as compared to homogeneous and half fracture patterns. Notably, by improving fluid mobility between the porous matrix and fractures, the addition of a surfactant to the fracturing fluids significantly enhanced the fluid invasion and flowback in all of the fracture patterns. The results demonstrate that the ROC model proposed in this work can be used to study the flowback process affected by properties such as wettability, permeability, initial water saturation, and reservoir pressure. Consequently, it has potential for guiding water management and chemical treatment in hydraulic fracturing.
- Open Access
- 1 January 2017
- Published by Georesursy LLC in Georesursy
- Vol. 19 (3) , 186-190
Technology of Multistage Hydraulic Fracturing in Horizontal Wells: Development Experience of Shaly Carbonates in the US and Its Adaptation for the Fields of the Republic of Tatarstan
- 1 January 2017
- Published by Georesursy LLC in Georesursy
- Vol. 19 (3) , 186-190
Open AccessTechnology of Multistage Hydraulic Fracturing in Horizontal Wells: Development Experience of Shaly Carbonates in the US and Its Adaptation for the Fields of the Republic of Tatarstan