Andrew E. Atalla
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andrew E. Atalla has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Guluzar Gorkem Buyukgoz
Otto H. York Department of Chemical and Materials Engineering, New Jersey Institute of Technology, Newark, NJ 07102, USA
1 shared publication - Jeremiah N. Castro
Otto H. York Department of Chemical and Materials Engineering, New Jersey Institute of Technology, Newark, NJ 07102, USA
1 shared publication - John G. Pentangelo
Otto H. York Department of Chemical and Materials Engineering, New Jersey Institute of Technology, Newark, NJ 07102, USA
1 shared publication - Rajesh N. Dave
New Jersey Center for Engineered Particulates, New Jersey Institute of Technology, Newark, NJ 07102, USA
1 shared publication - Siddharth Tripathi
Otto H. York Department of Chemical and Materials Engineering, New Jersey Institute of Technology, Newark, NJ 07102, USA
1 shared publication
Latest Publications
- Open Access
- 29 May 2021
- Published by MDPI AG in Pharmaceutics
- Vol. 13 (6) , 812
Impact of Mixing on Content Uniformity of Thin Polymer Films Containing Drug Micro-Doses
The impact of mixer type and critical process parameters (CPPs) on critical quality attributes (CQAs), including the drug content uniformity (CU) of slurry-cast polymer films loaded with micro-sized poorly water-soluble drugs were investigated. Previously untested hypothesis was that the best mixer at suitable CPPs promotes uniform drug dispersion within film precursors leading to acceptable dried-film CU at low, ~0.6 wt% drug concentrations. Taguchi design was utilized to select the best of three mixers; low-shear impeller, high-shear planetary, and high-intensity vibrational, for dried-film drug concentration of ~23 wt%. As-received fenofibrate, a model poorly water-soluble drug (~6 µm) was directly mixed with the hydroxypropyl methylcellulose (HPMC) and glycerin aqueous solution. Impeller and planetary mixers yielded desirable film relative standard deviation (RSD), while vibrational mixer could not. For the lowest dried-film drug concentration of ~0.6 wt%, only planetary mixer yielded RSD <6%. The precursor drug homogeneity was a sufficient but not a necessary condition for achieving dried-film RSD <6%. Thus, proper selection of mixer and its CPPs assured desirable film CQAs. However, minor drug particle aggregation was identified via re-dispersion testing which also led to incomplete drug release.
- 29 May 2021
- Published by MDPI AG in Pharmaceutics
- Vol. 13 (6) , 812
Open AccessImpact of Mixing on Content Uniformity of Thin Polymer Films Containing Drug Micro-Doses
The impact of mixer type and critical process parameters (CPPs) on critical quality attributes (CQAs), including the drug content uniformity (CU) of slurry-cast polymer films loaded with micro-sized poorly water-soluble drugs were investigated. Previously untested hypothesis was that the best mixer at suitable CPPs promotes uniform drug dispersion within film precursors leading to acceptable dried-film CU at low, ~0.6 wt% drug concentrations. Taguchi design was utilized to select the best of three mixers; low-shear impeller, high-shear planetary, and high-intensity vibrational, for dried-film drug concentration of ~23 wt%. As-received fenofibrate, a model poorly water-soluble drug (~6 µm) was directly mixed with the hydroxypropyl methylcellulose (HPMC) and glycerin aqueous solution. Impeller and planetary mixers yielded desirable film relative standard deviation (RSD), while vibrational mixer could not. For the lowest dried-film drug concentration of ~0.6 wt%, only planetary mixer yielded RSD <6%. The precursor drug homogeneity was a sufficient but not a necessary condition for achieving dried-film RSD <6%. Thus, proper selection of mixer and its CPPs assured desirable film CQAs. However, minor drug particle aggregation was identified via re-dispersion testing which also led to incomplete drug release.