Pan Dai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Pan Dai has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Xiangfei Chen
Nanjing University
6 shared publications - Yuechun Shi
YongJiang Laboratory
5 shared publications - Long Huang
Microwave-Photonics Technology Laboratory, Nanjing National Laboratory of Microstructures and School of Engineering and Applied Sciences, Nanjing University, Nanjing, Jiangsu Province China
3 shared publications - Rulei Xiao
Nanjing University
3 shared publications - Jilin Zheng
Army Engineering University of PLA, Nanjing, China
2 shared publications - Jun Lu
Key Laboratory of Intelligent Optical Sensing and Manipulation of the Ministry of Education & National Laboratory of Solid State Microstructures & College of Engineering and Applied Sciences & Institute of Optical Communication Engineering & Nanjing University-Tongding Joint Lab for Large-Scale Photonic Integrated Circuits, Nanjing University, Nanjing 210023, China
2 shared publications
Latest Publications
- 20 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 38 (24) , 6788-6800
Unified Performance Analysis of Hybrid FSO/RF System With Diversity Combining
Hybrid free space optical (FSO)/radio frequency (RF) systems have been proved to be reliable links for high-data-rate wireless backhauls. In this paper, we present a unified performance analysis of the hybrid FSO/RF transmission system which transmits the identical data in both links and implements two popular diversity combining schemes, namely, selection combining (SC) and maximal ratio combining (MRC), in the receiver. Specially, for the FSO link, the Gamma-Gamma turbulence with pointing errors under heterodyne detection (HD) and intensity modulation/direction detection (IM/DD) is considered in our analysis while the general - shadowed fading which unifies popular RF fading models is employed for the analysis of the RF link. As a result, unified closed-form expressions of outage probabilities and average bit error rates for different modulation schemes are derived. Analytical and Monte Carlo simulation results are provided to characterize the performance of the hybrid FSO/RF link which is compared to the single FSO link and the single RF link. The agreement between the analytical and simulation results confirms the unification of various FSO channels and RF fading scenarios into a single closed-form expression.
- 20 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 38 (24) , 6788-6800
Unified Performance Analysis of Hybrid FSO/RF System With Diversity Combining
Hybrid free space optical (FSO)/radio frequency (RF) systems have been proved to be reliable links for high-data-rate wireless backhauls. In this paper, we present a unified performance analysis of the hybrid FSO/RF transmission system which transmits the identical data in both links and implements two popular diversity combining schemes, namely, selection combining (SC) and maximal ratio combining (MRC), in the receiver. Specially, for the FSO link, the Gamma-Gamma turbulence with pointing errors under heterodyne detection (HD) and intensity modulation/direction detection (IM/DD) is considered in our analysis while the general - shadowed fading which unifies popular RF fading models is employed for the analysis of the RF link. As a result, unified closed-form expressions of outage probabilities and average bit error rates for different modulation schemes are derived. Analytical and Monte Carlo simulation results are provided to characterize the performance of the hybrid FSO/RF link which is compared to the single FSO link and the single RF link. The agreement between the analytical and simulation results confirms the unification of various FSO channels and RF fading scenarios into a single closed-form expression.
- 5 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 27 (2) , 1-14
Signal-to-Noise Ratio of Microwave Photonic Filter With an Interferometric Structure Based on an Incoherent Broadband Optical Source
A comprehensive investigation of the signal-to-noise ratio (SNR) of the microwave photonic filter (MPF) with an interferometric structure based on an incoherent broadband optical source (IBOS) is presented from the time and frequency domains, respectively. The interferometric structure and the IBOS in the MPF result in a beneficial single-bandpass radio- frequency (RF) response. However, the IBOS adds a large noise to the filtered RF signal. Therefore, the analysis of the SNR is of great importance for the design of this kind of MPFs. Theoretical analysis shows that the SNR is a function of the center frequency of the passband, the modulation index, the chromatic dispersion, and the shape of the IBOS. An experiment is performed to verify the theory, and experimental results agree well with the theoretical calculation.
- 5 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 27 (2) , 1-14
Signal-to-Noise Ratio of Microwave Photonic Filter With an Interferometric Structure Based on an Incoherent Broadband Optical Source
A comprehensive investigation of the signal-to-noise ratio (SNR) of the microwave photonic filter (MPF) with an interferometric structure based on an incoherent broadband optical source (IBOS) is presented from the time and frequency domains, respectively. The interferometric structure and the IBOS in the MPF result in a beneficial single-bandpass radio- frequency (RF) response. However, the IBOS adds a large noise to the filtered RF signal. Therefore, the analysis of the SNR is of great importance for the design of this kind of MPFs. Theoretical analysis shows that the SNR is a function of the center frequency of the passband, the modulation index, the chromatic dispersion, and the shape of the IBOS. An experiment is performed to verify the theory, and experimental results agree well with the theoretical calculation.
- 29 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 38 (21) , 6038-6046
High Single-Mode Stability Tunable In-Series Laser Array With High Wavelength-spacing Uniformity
Multi-wavelength distributed feedback laser array based tunable semiconductor lasers have been widely used owing to their high mode stability and simple tuning scheme. Comparing with the in-parallel laser array, the in-series one can avoid a large power loss caused by the optical combiner. However, the single-mode stability of an in-series laser array is vulnerable to the reflections of other lasers. Here we experimentally demonstrated a tunable in-series laser array with high single-mode stability and high uniformity of wavelength spacing. To reduce the impact of such reflections, the Bragg gratings in different lasers were designed in phase, and the grating phase error was reduced by utilizing the reconstruction-equivalent-chirp technique. Besides, a three-section laser structure was applied in each laser to increase the priority of the dominant lasing mode. Four lasers with small wavelength-spacings of 2.5 nm were integrated in the in-series laser array. According to the measurement results of 40 in-series laser arrays (160 lasers), wavelength deviations of 90.6% lasers were within ±0.2 nm, average wavelength spacings of 97.5% of the measured laser arrays were deviated from the design within ±0.2 nm, and SMSRs of 96.3% lasers were above 45 dB. The output power was above 25 mW and the relative intensity noise was below -130 dB/Hz. Like the in-parallel laser array, the proposed laser array can be applied in either continuous wavelength tuning or fast channel switching. For the continuous wavelength tuning applications, the 10-nm tuning range was obtained with a temperature tuning range of less than 20 °C. For the fast channel switching applications, 4 channels with 2.5-nm spacing are available, and the switching time between two channels was less than 300 ns.
- 29 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 38 (21) , 6038-6046
High Single-Mode Stability Tunable In-Series Laser Array With High Wavelength-spacing Uniformity
Multi-wavelength distributed feedback laser array based tunable semiconductor lasers have been widely used owing to their high mode stability and simple tuning scheme. Comparing with the in-parallel laser array, the in-series one can avoid a large power loss caused by the optical combiner. However, the single-mode stability of an in-series laser array is vulnerable to the reflections of other lasers. Here we experimentally demonstrated a tunable in-series laser array with high single-mode stability and high uniformity of wavelength spacing. To reduce the impact of such reflections, the Bragg gratings in different lasers were designed in phase, and the grating phase error was reduced by utilizing the reconstruction-equivalent-chirp technique. Besides, a three-section laser structure was applied in each laser to increase the priority of the dominant lasing mode. Four lasers with small wavelength-spacings of 2.5 nm were integrated in the in-series laser array. According to the measurement results of 40 in-series laser arrays (160 lasers), wavelength deviations of 90.6% lasers were within ±0.2 nm, average wavelength spacings of 97.5% of the measured laser arrays were deviated from the design within ±0.2 nm, and SMSRs of 96.3% lasers were above 45 dB. The output power was above 25 mW and the relative intensity noise was below -130 dB/Hz. Like the in-parallel laser array, the proposed laser array can be applied in either continuous wavelength tuning or fast channel switching. For the continuous wavelength tuning applications, the 10-nm tuning range was obtained with a temperature tuning range of less than 20 °C. For the fast channel switching applications, 4 channels with 2.5-nm spacing are available, and the switching time between two channels was less than 300 ns.
- 19 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 37 (21) , 5406-5416
Centralized Fiber-Distributed Data Communication and Sensing Convergence System Based on Microwave Photonics
A unified data communication and radar sensing system towards millimeter-wave (mm-wave) applications with extended coverage is proposed and experimentally demonstrated. The transmission and reception of mm-wave signals are implemented by microwave photonics technologies, such as superheterodyne optical carrier suppression (HeteroOCS) and analog photonic links based on polarization modulators (PolMs). The orthogonal frequency division multiplexing (OFDM) signal is employed for communications and radar sensing simultaneously. The HeteroOCS is used to up-convert the intermediate frequency (IF) OFDM signal to the mm-wave band in the central office (CO). Then the optical mm-wave signal is transmitted to the remote antenna units (RAUs) via optical fibers. The echo signal is received by the RAU which is remotely connected to the CO by a PolM-based photonic link. The chromatic dispersion of optical fibers in the transmitter and receiver links is overcome by the HeteroOCS and the PolM, respectively. In the proposed system, the baseband units (BBU) centralized in the CO is used to process the radar sensing signal. As a result, the fiber length puts a restriction on the data rate of the communication. We propose a pre-delayed trigger signal to overcome the fiber length limitation. A proof-of-concept experiment is performed. Two targets with distances of 1.64 m and 3.40 m are successfully detected separately. The communication function of the system is also verified. 1 m wireless transmission of 1.56 Gb/s data rate is achieved below the forward error correction limit.
- 19 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 37 (21) , 5406-5416
Centralized Fiber-Distributed Data Communication and Sensing Convergence System Based on Microwave Photonics
A unified data communication and radar sensing system towards millimeter-wave (mm-wave) applications with extended coverage is proposed and experimentally demonstrated. The transmission and reception of mm-wave signals are implemented by microwave photonics technologies, such as superheterodyne optical carrier suppression (HeteroOCS) and analog photonic links based on polarization modulators (PolMs). The orthogonal frequency division multiplexing (OFDM) signal is employed for communications and radar sensing simultaneously. The HeteroOCS is used to up-convert the intermediate frequency (IF) OFDM signal to the mm-wave band in the central office (CO). Then the optical mm-wave signal is transmitted to the remote antenna units (RAUs) via optical fibers. The echo signal is received by the RAU which is remotely connected to the CO by a PolM-based photonic link. The chromatic dispersion of optical fibers in the transmitter and receiver links is overcome by the HeteroOCS and the PolM, respectively. In the proposed system, the baseband units (BBU) centralized in the CO is used to process the radar sensing signal. As a result, the fiber length puts a restriction on the data rate of the communication. We propose a pre-delayed trigger signal to overcome the fiber length limitation. A proof-of-concept experiment is performed. Two targets with distances of 1.64 m and 3.40 m are successfully detected separately. The communication function of the system is also verified. 1 m wireless transmission of 1.56 Gb/s data rate is achieved below the forward error correction limit.
- 7 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 25 (6) , 1-9
A Hybrid Transverse Mode Resonance DFB Semiconductor Laser
We propose and theoretically analyze a hybrid transverse mode resonance DFB semiconductor laser which consists of one active section with π -phase shifted anti-symmetric Bragg grating ( π -ASBG) and two passive sections with uniform Bragg grating. The hybrid light resonance along with mode conversion between the fundamental transverse electric (TE 0 ) mode and first order transverse electric (TE 1 ) mode is formed by the π-ASBG. The emitted light from one facet with the TE 0 or TE 1 mode can be controlled by tuning the injection currents of the passive sections. As an example, a laser with ridge waveguide is designed and simulated. The transverse mode with the same wavelength is tuned by changing the injection currents of the passive sections. The suppression ratio between the two transverse modes reaches 18.4 dB and 18.7 dB when the TE 0 and TE 1 modes are emitted, respectively. A simple method for equivalently realizing the grating in the proposed laser was also analyzed. Therefore, as the transverse mode tunable light source, the proposed laser may benefit the future mode division multiplexing (MDM) systems for reconfigurability and more flexibility.
- 7 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 25 (6) , 1-9
A Hybrid Transverse Mode Resonance DFB Semiconductor Laser
We propose and theoretically analyze a hybrid transverse mode resonance DFB semiconductor laser which consists of one active section with π -phase shifted anti-symmetric Bragg grating ( π -ASBG) and two passive sections with uniform Bragg grating. The hybrid light resonance along with mode conversion between the fundamental transverse electric (TE 0 ) mode and first order transverse electric (TE 1 ) mode is formed by the π-ASBG. The emitted light from one facet with the TE 0 or TE 1 mode can be controlled by tuning the injection currents of the passive sections. As an example, a laser with ridge waveguide is designed and simulated. The transverse mode with the same wavelength is tuned by changing the injection currents of the passive sections. The suppression ratio between the two transverse modes reaches 18.4 dB and 18.7 dB when the TE 0 and TE 1 modes are emitted, respectively. A simple method for equivalently realizing the grating in the proposed laser was also analyzed. Therefore, as the transverse mode tunable light source, the proposed laser may benefit the future mode division multiplexing (MDM) systems for reconfigurability and more flexibility.
- Open Access
- 26 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 11 (2) , 1-10
Efficient TE-Polarized Mode-Order Converter Based on High-Index-Contrast Polygonal Slot in a Silicon-on-Insulator Waveguide
We proposed a new type of TE-polarized mode-order converter based on a deeply-etched polygonal slot on a silicon-on-insulator (SOI) waveguide. Along the transverse direction of the waveguide, two irregular boundary surfaces (BSs) of the slot can introduce high-contrast index modulation on guided modes, leading to multimode interference in the slot. Therefore, when the slot is optimized, we can achieve efficient mode conversions based on the multimode interference. As examples, mode converters from the fundamental transverse electric mode $\rm (TE_0)$ to the first-order transverse electric mode $\rm (TE_1)$ and to the second-order transverse electric mode $\rm (TE_2)$ have both been demonstrated with a short device length ( 97.6%), and a low modal crosstalk (< -20.0 dB) over a broad wavelength range from 1500 to 1600 nm (∼ 100 nm). In addition, based on different polygonal slots, other types of mode conversions such as from $\rm TE_1$ to $\rm TE_3$ and from $\rm TE_2$ to $\rm TE_1$ have be realized. Fabrication error tolerance of the proposed structure is analyzed. Owing to the high efficiency and compact size, the proposed structure could be applied to the on-chip mode division multiplexing (MDM) systems for high-density integration.- 26 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 11 (2) , 1-10
Open AccessEfficient TE-Polarized Mode-Order Converter Based on High-Index-Contrast Polygonal Slot in a Silicon-on-Insulator Waveguide
We proposed a new type of TE-polarized mode-order converter based on a deeply-etched polygonal slot on a silicon-on-insulator (SOI) waveguide. Along the transverse direction of the waveguide, two irregular boundary surfaces (BSs) of the slot can introduce high-contrast index modulation on guided modes, leading to multimode interference in the slot. Therefore, when the slot is optimized, we can achieve efficient mode conversions based on the multimode interference. As examples, mode converters from the fundamental transverse electric mode $\rm (TE_0)$ to the first-order transverse electric mode $\rm (TE_1)$ and to the second-order transverse electric mode $\rm (TE_2)$ have both been demonstrated with a short device length ( 97.6%), and a low modal crosstalk (< -20.0 dB) over a broad wavelength range from 1500 to 1600 nm (∼ 100 nm). In addition, based on different polygonal slots, other types of mode conversions such as from $\rm TE_1$ to $\rm TE_3$ and from $\rm TE_2$ to $\rm TE_1$ have be realized. Fabrication error tolerance of the proposed structure is analyzed. Owing to the high efficiency and compact size, the proposed structure could be applied to the on-chip mode division multiplexing (MDM) systems for high-density integration.