Jun Lu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jun Lu has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Rulei Xiao
Nanjing University
3 shared publications - Xiangfei Chen
Nanjing University
3 shared publications - Yuechun Shi
YongJiang Laboratory
3 shared publications - Zhenxing Sun
YongJiang Laboratory
3 shared publications - Jilin Zheng
Army Engineering University of PLA, Nanjing, China
2 shared publications - Pan Dai
School of Engineering and Applied Sciences, Nanjing University, Nanjing, Jiangsu China
2 shared publications
Latest Publications
- Open Access
- 1 January 2024
- Published by Shanghai Institute of Optics and Fine Mechanics in Chinese Optics Letters
- Vol. 22 (8) , 081401
Hybrid-integrated 200 Gb/s REC-DML array transmitter based on photonic wire bonding technology
An 8-channel hybrid-integrated chip for 200 Gb/s (8 × 25 Gb/s) signal transmission has been demonstrated. The channels are all within the O-band, and with a spacing of 800 GHz. The core of this chip is a monolithic integrated multi-wavelength laser array of 8 directly-modulated distributed feedback (DFB) lasers. By using the reconstruction equivalent chirp technique, multi-wavelength integration and asymmetric phase shift structures are achieved in the laser array. The output laser beams of the array are combined by a planar light-wave circuit, which is hybrid-integrated with the laser array by photonic wire bonding. Experiment results of this transmitter chip show good single-mode working of each unit laser, with a side-mode suppression ratio above 50 dB, and the modulation bandwidth is above 20 GHz. Clear eye diagrams are obtained in the lasers for 25 Gb/s non-return-to-zero modulation, which implies a total 200 Gb/s transmission rate for the whole chip.
- 1 January 2024
- Published by Shanghai Institute of Optics and Fine Mechanics in Chinese Optics Letters
- Vol. 22 (8) , 081401
Open AccessHybrid-integrated 200 Gb/s REC-DML array transmitter based on photonic wire bonding technology
An 8-channel hybrid-integrated chip for 200 Gb/s (8 × 25 Gb/s) signal transmission has been demonstrated. The channels are all within the O-band, and with a spacing of 800 GHz. The core of this chip is a monolithic integrated multi-wavelength laser array of 8 directly-modulated distributed feedback (DFB) lasers. By using the reconstruction equivalent chirp technique, multi-wavelength integration and asymmetric phase shift structures are achieved in the laser array. The output laser beams of the array are combined by a planar light-wave circuit, which is hybrid-integrated with the laser array by photonic wire bonding. Experiment results of this transmitter chip show good single-mode working of each unit laser, with a side-mode suppression ratio above 50 dB, and the modulation bandwidth is above 20 GHz. Clear eye diagrams are obtained in the lasers for 25 Gb/s non-return-to-zero modulation, which implies a total 200 Gb/s transmission rate for the whole chip.
- 29 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 38 (21) , 6038-6046
High Single-Mode Stability Tunable In-Series Laser Array With High Wavelength-spacing Uniformity
Multi-wavelength distributed feedback laser array based tunable semiconductor lasers have been widely used owing to their high mode stability and simple tuning scheme. Comparing with the in-parallel laser array, the in-series one can avoid a large power loss caused by the optical combiner. However, the single-mode stability of an in-series laser array is vulnerable to the reflections of other lasers. Here we experimentally demonstrated a tunable in-series laser array with high single-mode stability and high uniformity of wavelength spacing. To reduce the impact of such reflections, the Bragg gratings in different lasers were designed in phase, and the grating phase error was reduced by utilizing the reconstruction-equivalent-chirp technique. Besides, a three-section laser structure was applied in each laser to increase the priority of the dominant lasing mode. Four lasers with small wavelength-spacings of 2.5 nm were integrated in the in-series laser array. According to the measurement results of 40 in-series laser arrays (160 lasers), wavelength deviations of 90.6% lasers were within ±0.2 nm, average wavelength spacings of 97.5% of the measured laser arrays were deviated from the design within ±0.2 nm, and SMSRs of 96.3% lasers were above 45 dB. The output power was above 25 mW and the relative intensity noise was below -130 dB/Hz. Like the in-parallel laser array, the proposed laser array can be applied in either continuous wavelength tuning or fast channel switching. For the continuous wavelength tuning applications, the 10-nm tuning range was obtained with a temperature tuning range of less than 20 °C. For the fast channel switching applications, 4 channels with 2.5-nm spacing are available, and the switching time between two channels was less than 300 ns.
- 29 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 38 (21) , 6038-6046
High Single-Mode Stability Tunable In-Series Laser Array With High Wavelength-spacing Uniformity
Multi-wavelength distributed feedback laser array based tunable semiconductor lasers have been widely used owing to their high mode stability and simple tuning scheme. Comparing with the in-parallel laser array, the in-series one can avoid a large power loss caused by the optical combiner. However, the single-mode stability of an in-series laser array is vulnerable to the reflections of other lasers. Here we experimentally demonstrated a tunable in-series laser array with high single-mode stability and high uniformity of wavelength spacing. To reduce the impact of such reflections, the Bragg gratings in different lasers were designed in phase, and the grating phase error was reduced by utilizing the reconstruction-equivalent-chirp technique. Besides, a three-section laser structure was applied in each laser to increase the priority of the dominant lasing mode. Four lasers with small wavelength-spacings of 2.5 nm were integrated in the in-series laser array. According to the measurement results of 40 in-series laser arrays (160 lasers), wavelength deviations of 90.6% lasers were within ±0.2 nm, average wavelength spacings of 97.5% of the measured laser arrays were deviated from the design within ±0.2 nm, and SMSRs of 96.3% lasers were above 45 dB. The output power was above 25 mW and the relative intensity noise was below -130 dB/Hz. Like the in-parallel laser array, the proposed laser array can be applied in either continuous wavelength tuning or fast channel switching. For the continuous wavelength tuning applications, the 10-nm tuning range was obtained with a temperature tuning range of less than 20 °C. For the fast channel switching applications, 4 channels with 2.5-nm spacing are available, and the switching time between two channels was less than 300 ns.
- Open Access
- 31 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 11 (6) , 1-9
Experimental Demonstration of π Equivalent Phase-Shifted SBG Laser With Controlled Distributed Phase Shift
We designed and fabricated a π equivalent phase-shifted sampled Bragg grating (SBG) semiconductor laser with a controlled distributed phase shift. The phase shift is equivalently realized with reconstruction-equivalent-chirp (REC) technique. The laser is divided into three sections with the same length. By injecting different currents into the side and middle sections, a distributed phase shift can be introduced. The lasing wavelength can be continuously tuned by the injection currents. In our experiment, when the total current keeps 130 mA, the lasing wavelength can be continuously tuned by 1.2 nm. During the tuning, the side mode suppression ratio keeps above 40 dB and the output power varies only 1.3 dB. Therefore, the proposed method provides an alternative solution for the multiwavelength laser arrays in dense wavelength-division multiplexing (DWDM) systems.
- 31 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 11 (6) , 1-9
Open AccessExperimental Demonstration of π Equivalent Phase-Shifted SBG Laser With Controlled Distributed Phase Shift
We designed and fabricated a π equivalent phase-shifted sampled Bragg grating (SBG) semiconductor laser with a controlled distributed phase shift. The phase shift is equivalently realized with reconstruction-equivalent-chirp (REC) technique. The laser is divided into three sections with the same length. By injecting different currents into the side and middle sections, a distributed phase shift can be introduced. The lasing wavelength can be continuously tuned by the injection currents. In our experiment, when the total current keeps 130 mA, the lasing wavelength can be continuously tuned by 1.2 nm. During the tuning, the side mode suppression ratio keeps above 40 dB and the output power varies only 1.3 dB. Therefore, the proposed method provides an alternative solution for the multiwavelength laser arrays in dense wavelength-division multiplexing (DWDM) systems.
- 7 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 25 (6) , 1-9
A Hybrid Transverse Mode Resonance DFB Semiconductor Laser
We propose and theoretically analyze a hybrid transverse mode resonance DFB semiconductor laser which consists of one active section with π -phase shifted anti-symmetric Bragg grating ( π -ASBG) and two passive sections with uniform Bragg grating. The hybrid light resonance along with mode conversion between the fundamental transverse electric (TE 0 ) mode and first order transverse electric (TE 1 ) mode is formed by the π-ASBG. The emitted light from one facet with the TE 0 or TE 1 mode can be controlled by tuning the injection currents of the passive sections. As an example, a laser with ridge waveguide is designed and simulated. The transverse mode with the same wavelength is tuned by changing the injection currents of the passive sections. The suppression ratio between the two transverse modes reaches 18.4 dB and 18.7 dB when the TE 0 and TE 1 modes are emitted, respectively. A simple method for equivalently realizing the grating in the proposed laser was also analyzed. Therefore, as the transverse mode tunable light source, the proposed laser may benefit the future mode division multiplexing (MDM) systems for reconfigurability and more flexibility.
- 7 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 25 (6) , 1-9
A Hybrid Transverse Mode Resonance DFB Semiconductor Laser
We propose and theoretically analyze a hybrid transverse mode resonance DFB semiconductor laser which consists of one active section with π -phase shifted anti-symmetric Bragg grating ( π -ASBG) and two passive sections with uniform Bragg grating. The hybrid light resonance along with mode conversion between the fundamental transverse electric (TE 0 ) mode and first order transverse electric (TE 1 ) mode is formed by the π-ASBG. The emitted light from one facet with the TE 0 or TE 1 mode can be controlled by tuning the injection currents of the passive sections. As an example, a laser with ridge waveguide is designed and simulated. The transverse mode with the same wavelength is tuned by changing the injection currents of the passive sections. The suppression ratio between the two transverse modes reaches 18.4 dB and 18.7 dB when the TE 0 and TE 1 modes are emitted, respectively. A simple method for equivalently realizing the grating in the proposed laser was also analyzed. Therefore, as the transverse mode tunable light source, the proposed laser may benefit the future mode division multiplexing (MDM) systems for reconfigurability and more flexibility.