Zheyuan Yu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Zheyuan Yu has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Wenjie Chen
State Key Laboratory of Electrical Insulation and Power Equipment, Xian Jiaotong University, Xian, China
7 shared publications - Xu Yang
Xi’an Jiaotong University
6 shared publications - Kangping Wang
State Key Laboratory of Electrical Insulation and Power Equipment, School of Electrical Engineering, Xian Jiaotong University, Xian, China
4 shared publications - Jiarui Wu
State Key Laboratory of Electrical Insulation and Power Equipment, Xian Jiaotong University, Xian, China
3 shared publications - Laili Wang
State Key Laboratory of Electrical Insulation and Power Equipment, Xian Jiaotong University, Xian, China
3 shared publications Yongxing Zhou
State Key Laboratory of Electrical Insulation and Power Equipment, Xian Jiaotong University, Xian, China
3 shared publications
Latest Publications
- 16 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (6) , 8691-8702
Design and Optimization of Fractional-Turn Transformer With Low Core Loss and Profile
In data center applications where most power supplies are in light-load operation, hence optimizing light-load efficiency is immensely crucial. In this article, a fractional-turn planar transformer with an elliptical core is proposed, which reduces the eddy loss of the core and improves the light-load efficiency. This structure also reduces the magnetic core profile and improves the power density. Magnetic loss theory, winding configuration and core optimization were analyzed in detail. Finally, a detailed optimization process about transformer is carried out based on finite-element analysis, and two 1 MHz 380 V–12 V 720 W LLC converters are designed based on the conventional fractional-turn transformer and the proposed fractional-turn transformer, respectively.
- 16 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (6) , 8691-8702
Design and Optimization of Fractional-Turn Transformer With Low Core Loss and Profile
In data center applications where most power supplies are in light-load operation, hence optimizing light-load efficiency is immensely crucial. In this article, a fractional-turn planar transformer with an elliptical core is proposed, which reduces the eddy loss of the core and improves the light-load efficiency. This structure also reduces the magnetic core profile and improves the power density. Magnetic loss theory, winding configuration and core optimization were analyzed in detail. Finally, a detailed optimization process about transformer is carried out based on finite-element analysis, and two 1 MHz 380 V–12 V 720 W LLC converters are designed based on the conventional fractional-turn transformer and the proposed fractional-turn transformer, respectively.
- 16 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (12) , 16870-16874
A Novel Virtual Capacitance Enhancement-Based Active EMI Filter for CM Noise Attenuation
During practical applications, the capacitance limitation creates obstacles and demands a big value of common mode (CM) choke for low-frequency noise attenuation. Traditional active electromagnetic interference (EMI) filter also demands big capacitance or the performance of filter is sensitive to the tolerance of used capacitor. To cope with those problems, this article proposes a virtual capacitance enhancement-based active EMI filter (VCE-AEF). By injecting controlled compensation current flowing through small capacitor, active part of VCE-AEF shows characteristics as negative capacitor. Combined with small positive capacitor, total impedance is decreased which means equivalent capacitance is virtually boosted. The performance of VCE-AEF remains stable and is less related with the capacitance of the used positive capacitor. Experimental results show that the noise attenuation achieved by the proposed VCE-AEF with 2.2 nF capacitors is close to the performance with 220 nF Y capacitors during low-frequency range.
- 16 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (12) , 16870-16874
A Novel Virtual Capacitance Enhancement-Based Active EMI Filter for CM Noise Attenuation
During practical applications, the capacitance limitation creates obstacles and demands a big value of common mode (CM) choke for low-frequency noise attenuation. Traditional active electromagnetic interference (EMI) filter also demands big capacitance or the performance of filter is sensitive to the tolerance of used capacitor. To cope with those problems, this article proposes a virtual capacitance enhancement-based active EMI filter (VCE-AEF). By injecting controlled compensation current flowing through small capacitor, active part of VCE-AEF shows characteristics as negative capacitor. Combined with small positive capacitor, total impedance is decreased which means equivalent capacitance is virtually boosted. The performance of VCE-AEF remains stable and is less related with the capacitance of the used positive capacitor. Experimental results show that the noise attenuation achieved by the proposed VCE-AEF with 2.2 nF capacitors is close to the performance with 220 nF Y capacitors during low-frequency range.
- 25 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (1) , 592-609
A Novel Low-Winding-Loss Circulated Interleaving Structure for Planar Transformers Based on Current Invariance Principle
With the increase of frequency, the winding loss of planar transformers rises significantly due to the skin and proximity effects, making it one of the major contributors to converter loss. Paralleling layers is commonly adopted in high-current applications to reduce winding loss. However, the most widely used structure, symmetric interleaving, is not the minimum-loss structure according to Ferreira’s model, even though it can achieve current sharing. In this article, a new interleaving structure named circulated interleaving is proposed. This structure is invented based on the current invariance principle proposed in this paper and has only 50% loss of symmetric interleaving. The current sharing condition and the minimum winding loss of the two structures are analyzed and compared systematically by mathematical derivation. The 2D simulations validate the consistency with theory under ideal conditions and explore the variations in current distribution and losses under non-ideal conditions, demonstrating that the structure exhibits the same level of advancement under non-ideal conditions. Vias effect is also evaluated under 3D simulations, indicating only 50% inner-core winding loss compared to the symmetric interleaving. 6 transformers with different interleaving structures and different copper thickness are built and tested and the advantages of the proposed interleaving structure are validated. Practical considerations such as capacitance, leakage inductance, core shape, and heat are also discussed.
- 25 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (1) , 592-609
A Novel Low-Winding-Loss Circulated Interleaving Structure for Planar Transformers Based on Current Invariance Principle
With the increase of frequency, the winding loss of planar transformers rises significantly due to the skin and proximity effects, making it one of the major contributors to converter loss. Paralleling layers is commonly adopted in high-current applications to reduce winding loss. However, the most widely used structure, symmetric interleaving, is not the minimum-loss structure according to Ferreira’s model, even though it can achieve current sharing. In this article, a new interleaving structure named circulated interleaving is proposed. This structure is invented based on the current invariance principle proposed in this paper and has only 50% loss of symmetric interleaving. The current sharing condition and the minimum winding loss of the two structures are analyzed and compared systematically by mathematical derivation. The 2D simulations validate the consistency with theory under ideal conditions and explore the variations in current distribution and losses under non-ideal conditions, demonstrating that the structure exhibits the same level of advancement under non-ideal conditions. Vias effect is also evaluated under 3D simulations, indicating only 50% inner-core winding loss compared to the symmetric interleaving. 6 transformers with different interleaving structures and different copper thickness are built and tested and the advantages of the proposed interleaving structure are validated. Practical considerations such as capacitance, leakage inductance, core shape, and heat are also discussed.
- 3 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 11 (6) , 5675-5689
Adaptive Optimization Charging Strategy for LCC Resonant Capacitor Charging Power Supply
In repetitive pulse power applications, the charging capacitor time occupies most of time in a pulse period, and the important parameters such as pulse repetition rate are restricted by the charging speed of the capacitor. To accelerate the charging speed and make full use of the components’ capacity, a novel adaptive optimization charging (AOC) strategy is proposed for capacitor charging power supply (CCPS). Moreover, to improve the accuracy of LCC model, a fundamental harmonic approximation model based on continuous resonant current (CRC-FHA) is put forward. Compared with conventional FHA which uses a discontinuous transformer current iT , the CRC-FHA model is established by adopting the continuous and more sinusoidal resonant current ir . The analytical expressions are derived for the maximum resonant current Imax , ZVS boundary and the multidimensional relationship between the output voltage, the peak value of resonant current, average output current, and switching frequency. Accordingly, the proposed AOC strategy sets the maximum resonant current boundary, the ZVS charging boundary, and the upper and lower switching frequency limits as constraints to get adaptive reference output current values in real-time to make full use of the capacity of the converter to improve the charging speed. Compared with a hybrid CC-CP (HCC-CP) charging profile, the proposed AOC strategy has an advantage in charging speed and soft switching range with the same maximum resonant current. Finally, the accuracy of the FHA model adopting resonant current for LCC resonant converter and the effectiveness of AOC strategy is verified by the simulation and a 2174 W LCC resonant converter.
- 3 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 11 (6) , 5675-5689
Adaptive Optimization Charging Strategy for LCC Resonant Capacitor Charging Power Supply
In repetitive pulse power applications, the charging capacitor time occupies most of time in a pulse period, and the important parameters such as pulse repetition rate are restricted by the charging speed of the capacitor. To accelerate the charging speed and make full use of the components’ capacity, a novel adaptive optimization charging (AOC) strategy is proposed for capacitor charging power supply (CCPS). Moreover, to improve the accuracy of LCC model, a fundamental harmonic approximation model based on continuous resonant current (CRC-FHA) is put forward. Compared with conventional FHA which uses a discontinuous transformer current iT , the CRC-FHA model is established by adopting the continuous and more sinusoidal resonant current ir . The analytical expressions are derived for the maximum resonant current Imax , ZVS boundary and the multidimensional relationship between the output voltage, the peak value of resonant current, average output current, and switching frequency. Accordingly, the proposed AOC strategy sets the maximum resonant current boundary, the ZVS charging boundary, and the upper and lower switching frequency limits as constraints to get adaptive reference output current values in real-time to make full use of the capacity of the converter to improve the charging speed. Compared with a hybrid CC-CP (HCC-CP) charging profile, the proposed AOC strategy has an advantage in charging speed and soft switching range with the same maximum resonant current. Finally, the accuracy of the FHA model adopting resonant current for LCC resonant converter and the effectiveness of AOC strategy is verified by the simulation and a 2174 W LCC resonant converter.
- 23 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (11) , 14274-14291
2-D Analytical Copper Loss Model for PCB and Copper Foil Magnetics With Arbitrary Air Gaps
The modeling and optimization of copper losses are the basis of magnetic designs. By solving 2-D diffusion and Laplace equations, this paper proposes a 2-D analytical copper loss model for PCB inductors and transformers with arbitrary air gaps. The copper loss resistance is decoupled into skin, proximity and fringing resistances. The fringing resistance is caused by the inhomogeneity of magnetic induction expressed as the Fourier series. Based on the proposed model, some conclusions are derived theoretically. For example, fringing resistance of transformers is independent of the arrangements of primary and secondary windings, and fringing resistance increases with winding width, which could be a theoretical reason why matrix transformers should be used in some applications. The proposed model is verified by simulation with a 6.0% average error and by experiment with a 7.7% average error.
- 23 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (11) , 14274-14291
2-D Analytical Copper Loss Model for PCB and Copper Foil Magnetics With Arbitrary Air Gaps
The modeling and optimization of copper losses are the basis of magnetic designs. By solving 2-D diffusion and Laplace equations, this paper proposes a 2-D analytical copper loss model for PCB inductors and transformers with arbitrary air gaps. The copper loss resistance is decoupled into skin, proximity and fringing resistances. The fringing resistance is caused by the inhomogeneity of magnetic induction expressed as the Fourier series. Based on the proposed model, some conclusions are derived theoretically. For example, fringing resistance of transformers is independent of the arrangements of primary and secondary windings, and fringing resistance increases with winding width, which could be a theoretical reason why matrix transformers should be used in some applications. The proposed model is verified by simulation with a 6.0% average error and by experiment with a 7.7% average error.
- 5 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (10) , 11461-11468
A Novel Pyramid Winding for PCB Planar Inductors With Fewer Copper Layers and Lower AC Copper Loss
Relying on the advantages of small size, good controllability and consistency, PCB inductors are being widely used. For PCB inductors, reducing copper loss is one of the key issues. Although some researches focus on fringing effect in PCB planar winding, there are few methods to reduce proximity loss for PCB inductor. Regarding the issues above, this paper first improves Ferreira's one-dimensional model to accommodate the core feature of PCB winding: varying number of turns per layer. With this model, pyramid theorem is proposed that swapping the layer with fewer turns into positions farther away from the air gaps can lower the total winding losses. Based on the theorem, this manuscript proposes a novel PCB inductor winding structure named pyramid winding, which has fewer (or equal) turns on layers further from air gaps. Pyramid winding has less copper loss, fewer copper layers, smaller size and lower cost. In experiment, inductor prototypes with the same six turns and ferrite pot cores but different PCB winding arrangements are built for a 300-kHz 2700-W LLC converter. Tests on inductor resistance and converter efficiency are done and pyramid theorem and the effectiveness of pyramid winding are verified.
- 5 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (10) , 11461-11468
A Novel Pyramid Winding for PCB Planar Inductors With Fewer Copper Layers and Lower AC Copper Loss
Relying on the advantages of small size, good controllability and consistency, PCB inductors are being widely used. For PCB inductors, reducing copper loss is one of the key issues. Although some researches focus on fringing effect in PCB planar winding, there are few methods to reduce proximity loss for PCB inductor. Regarding the issues above, this paper first improves Ferreira's one-dimensional model to accommodate the core feature of PCB winding: varying number of turns per layer. With this model, pyramid theorem is proposed that swapping the layer with fewer turns into positions farther away from the air gaps can lower the total winding losses. Based on the theorem, this manuscript proposes a novel PCB inductor winding structure named pyramid winding, which has fewer (or equal) turns on layers further from air gaps. Pyramid winding has less copper loss, fewer copper layers, smaller size and lower cost. In experiment, inductor prototypes with the same six turns and ferrite pot cores but different PCB winding arrangements are built for a 300-kHz 2700-W LLC converter. Tests on inductor resistance and converter efficiency are done and pyramid theorem and the effectiveness of pyramid winding are verified.
- 23 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (9) , 10081-10085
A Novel Neutral Point-Based Active EMI Filter for Common Mode Noise Attenuation
This letter proposed a new configuration of neutral point-based common mode (CM) active electromagnetic interference (EMI) filter (NP-CM-AEF). It is achieved by setting the reference of filtering system to the neutral point of equipment under test. Therefore, CM noise could be sensed across neutral point and ground. Meanwhile, compensation signal could be built by op-amp and re-injected to cancel the initial CM noise. The main advantage of the proposed NP-CM-AEF lies in that no more noise separation such as bulky passive CM transformer is needed to get pure CM noise. The whole filter becomes smaller, lighter, and more compact compared with traditional CM AEF. Working principle is analyzed in details and hardware experimental tests are also performed. It shows that the proposed NP-CM-AEF has a good attenuation to CM noise and total size is pretty tiny.
- 23 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (9) , 10081-10085
A Novel Neutral Point-Based Active EMI Filter for Common Mode Noise Attenuation
This letter proposed a new configuration of neutral point-based common mode (CM) active electromagnetic interference (EMI) filter (NP-CM-AEF). It is achieved by setting the reference of filtering system to the neutral point of equipment under test. Therefore, CM noise could be sensed across neutral point and ground. Meanwhile, compensation signal could be built by op-amp and re-injected to cancel the initial CM noise. The main advantage of the proposed NP-CM-AEF lies in that no more noise separation such as bulky passive CM transformer is needed to get pure CM noise. The whole filter becomes smaller, lighter, and more compact compared with traditional CM AEF. Working principle is analyzed in details and hardware experimental tests are also performed. It shows that the proposed NP-CM-AEF has a good attenuation to CM noise and total size is pretty tiny.
- 6 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 36 (11) , 12189-12195
A Novel High-Current Planar Inductor With Cooling Fins Based on 3-D Printing
This letter proposed a novel high-current planar inductor with cooling fins based on 3-D printing and its copper winding is 3-D printed by using selective laser melting technology. The 3-D-printed winding is designed for high-current applications based on 3-D space and can work as both winding and cooling fins. Compared with conventional printed circuit board (PCB) planar inductor, the proposed planar inductor not only has better performance, such as low dc resistance (DCR), ac resistance, and temperature rise, without volume increasing, but also has the superiorities of conventional PCB planar magnetics, such as ease of manufacture and controllability. To verify its performance, a 100-A-output buck converter using the proposed inductor was fabricated and compared with another identical buck converter using a conventional PCB inductor with the same size. The DCR of the proposed inductor is almost one-fifth of the PCB inductor. Besides, the efficiency of the buck converter with the proposed inductor is always over 0.5% higher than that with PCB inductor under different loads and its maximum efficiency is nearly 1% higher at light load. Furthermore, the maximum temperature rise of the proposed inductor is 26.8 ° C under full load, only one-third of the PCB planar inductor. In other words, the proposed inductor can work well under 100-A current, whereas the traditional PCB inductor cannot due to too high temperature (103.8 ° C).
- 6 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 36 (11) , 12189-12195
A Novel High-Current Planar Inductor With Cooling Fins Based on 3-D Printing
This letter proposed a novel high-current planar inductor with cooling fins based on 3-D printing and its copper winding is 3-D printed by using selective laser melting technology. The 3-D-printed winding is designed for high-current applications based on 3-D space and can work as both winding and cooling fins. Compared with conventional printed circuit board (PCB) planar inductor, the proposed planar inductor not only has better performance, such as low dc resistance (DCR), ac resistance, and temperature rise, without volume increasing, but also has the superiorities of conventional PCB planar magnetics, such as ease of manufacture and controllability. To verify its performance, a 100-A-output buck converter using the proposed inductor was fabricated and compared with another identical buck converter using a conventional PCB inductor with the same size. The DCR of the proposed inductor is almost one-fifth of the PCB inductor. Besides, the efficiency of the buck converter with the proposed inductor is always over 0.5% higher than that with PCB inductor under different loads and its maximum efficiency is nearly 1% higher at light load. Furthermore, the maximum temperature rise of the proposed inductor is 26.8 ° C under full load, only one-third of the PCB planar inductor. In other words, the proposed inductor can work well under 100-A current, whereas the traditional PCB inductor cannot due to too high temperature (103.8 ° C).
- Open Access
- 15 February 2019
- Published by EDP Sciences in Mathematical Modelling of Natural Phenomena
- Vol. 14 (3) , 301
Modeling and analysis of fractional neutral disturbance waves in arterial vessels
The behavior of neutral disturbance in arterial vessels has attracted more and more attention in recent decades because it carries some important information which can be applied to predict and diagnose related heart disease, such as arteriosclerosis and hypertension, etc. Because of the complexity of blood flow in arteries, it is very necessary to construct accurate mathematical model and analyze the mechanical behavior of neutral disturbance in arterial vessels. In this paper, start from the basic equations of blood flow and the two-dimensional Navier–Stokes equation, the vorticity equation describing the disturbance flow is presented. Then, by use of multi-scale analysis and perturbation expansion method, the ZK equation is put forward which can reflect the behavior of the neutral perturbation flow in arterial vessels. Compared with the traditional KdV model, the model established in the paper can show the propagation of the disturbance flow in the radius direction. Furthermore, the time-fractional ZK equation is derived by semi-inverse method and Agrawal’s method, which is more convenient and accurate for discussing the feature of neutral disturbance in arterial vessels and can provide more information for analyzing some related heart disease. Meanwhile, with the help of the modified extended tanh method, the above mentioned equation is solved. The results show that neutral disturbance exists in arterial vessels and propagates in the form of solitary waves. By calculating, we find the relation of the stroke volume with vascular radius, blood flow velocity as well as the fractional order parameter α, which is very meaningful for preventing and treating related heart disease because the stroke volume is closely linked with heart disease.
- 15 February 2019
- Published by EDP Sciences in Mathematical Modelling of Natural Phenomena
- Vol. 14 (3) , 301
Open AccessModeling and analysis of fractional neutral disturbance waves in arterial vessels
The behavior of neutral disturbance in arterial vessels has attracted more and more attention in recent decades because it carries some important information which can be applied to predict and diagnose related heart disease, such as arteriosclerosis and hypertension, etc. Because of the complexity of blood flow in arteries, it is very necessary to construct accurate mathematical model and analyze the mechanical behavior of neutral disturbance in arterial vessels. In this paper, start from the basic equations of blood flow and the two-dimensional Navier–Stokes equation, the vorticity equation describing the disturbance flow is presented. Then, by use of multi-scale analysis and perturbation expansion method, the ZK equation is put forward which can reflect the behavior of the neutral perturbation flow in arterial vessels. Compared with the traditional KdV model, the model established in the paper can show the propagation of the disturbance flow in the radius direction. Furthermore, the time-fractional ZK equation is derived by semi-inverse method and Agrawal’s method, which is more convenient and accurate for discussing the feature of neutral disturbance in arterial vessels and can provide more information for analyzing some related heart disease. Meanwhile, with the help of the modified extended tanh method, the above mentioned equation is solved. The results show that neutral disturbance exists in arterial vessels and propagates in the form of solitary waves. By calculating, we find the relation of the stroke volume with vascular radius, blood flow velocity as well as the fractional order parameter α, which is very meaningful for preventing and treating related heart disease because the stroke volume is closely linked with heart disease.