Jiarui Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jiarui Wu has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Kangping Wang
State Key Laboratory of Electrical Insulation and Power Equipment, School of Electrical Engineering, Xian Jiaotong University, Xian, China
10 shared publications - Xu Yang
Xi’an Jiaotong University
9 shared publications - Wenjie Chen
State Key Laboratory of Electrical Insulation and Power Equipment, Xian Jiaotong University, Xian, China
8 shared publications - Laili Wang
State Key Laboratory of Electrical Insulation and Power Equipment, Xian Jiaotong University, Xian, China
5 shared publications - Xingwei Huang
State Key Laboratory of Electrical Insulation and Power Equipment, School of Electrical Engineering, Xian Jiaotong University, Xian, China
4 shared publications - Zheyuan Yu
State Key Laboratory of Electrical Insulation and Power Equipment, Xian Jiaotong University, Xian, China
3 shared publications
Latest Publications
- 26 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (4) , 8768-8783
Wide Voltage-Regulation Range Synchronous-Rectifier LLC Converter With Novel Operation Modes
Traditionally, the energy feedback in synchronous rectifier (SR) LLC converter was once considered to only have the ability to reduce the voltage gain. In this article, a kind of special energy feedback caused by the novel operation modes of LLC resonant converter is proposed for improving voltage gain. Compared to the P, O, and N stages in conventional LLC converter, stage F is built by controlling the turn-on early time of the SR. By using the proposed operation modes, not only zero-voltage switching (ZVS) of both the primary-side and secondary-side switches is achieved, but the voltage gain of the LLC converter can be increased significantly with a narrow switching frequency range and a smaller magnetizing inductance circulating current. In addition, the proposed operation modes are simple and easy to be utilized in full bridge, half bridge, and so on; all kinds of LLC converters thus can form a new general control strategy of the SR LLC. Finally, a 100-W half-bridge SR LLC dc-dc converter prototype with a wide voltage-regulation range is implemented to validate the proposed operation modes and the theoretical analysis.
- 26 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (4) , 8768-8783
Wide Voltage-Regulation Range Synchronous-Rectifier LLC Converter With Novel Operation Modes
Traditionally, the energy feedback in synchronous rectifier (SR) LLC converter was once considered to only have the ability to reduce the voltage gain. In this article, a kind of special energy feedback caused by the novel operation modes of LLC resonant converter is proposed for improving voltage gain. Compared to the P, O, and N stages in conventional LLC converter, stage F is built by controlling the turn-on early time of the SR. By using the proposed operation modes, not only zero-voltage switching (ZVS) of both the primary-side and secondary-side switches is achieved, but the voltage gain of the LLC converter can be increased significantly with a narrow switching frequency range and a smaller magnetizing inductance circulating current. In addition, the proposed operation modes are simple and easy to be utilized in full bridge, half bridge, and so on; all kinds of LLC converters thus can form a new general control strategy of the SR LLC. Finally, a 100-W half-bridge SR LLC dc-dc converter prototype with a wide voltage-regulation range is implemented to validate the proposed operation modes and the theoretical analysis.
- 7 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (2) , 2715-2720
A Novel All-Passive Resonant Gate for LLC DCX Synchronous Rectification
The drive losses of synchronous rectifier (SR) mosfets become significant factor limiting the efficiency of high-frequency, low-voltage, and high-current output LLC dc transformer (LLC DCX) in data center power supply applications. The resonant gate driver (RGD) can reduce drive losses, but both semiconductor devices and external power supply are required in the current RGDs, which results in more losses and footprint. An all-passive resonant gate driver (APRGD) is proposed in this letter, which consists only passive components, including inductances, capacitances, and transformer windings. The operation principle and parameter optimization method of the proposed APRGD are illustrated in detail, which is then verified by experiments. The peak efficiency of the prototype is improved by 0.83% after using APRGD, and SR drive losses are reduced by 93.4%. In addition, the footprint of APRGD is similar to that of conventional drive ICs. The proposed APRGD has advantages in efficiency and power density compared to current RGDs.
- 7 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (2) , 2715-2720
A Novel All-Passive Resonant Gate for LLC DCX Synchronous Rectification
The drive losses of synchronous rectifier (SR) mosfets become significant factor limiting the efficiency of high-frequency, low-voltage, and high-current output LLC dc transformer (LLC DCX) in data center power supply applications. The resonant gate driver (RGD) can reduce drive losses, but both semiconductor devices and external power supply are required in the current RGDs, which results in more losses and footprint. An all-passive resonant gate driver (APRGD) is proposed in this letter, which consists only passive components, including inductances, capacitances, and transformer windings. The operation principle and parameter optimization method of the proposed APRGD are illustrated in detail, which is then verified by experiments. The peak efficiency of the prototype is improved by 0.83% after using APRGD, and SR drive losses are reduced by 93.4%. In addition, the footprint of APRGD is similar to that of conventional drive ICs. The proposed APRGD has advantages in efficiency and power density compared to current RGDs.
- 29 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (12) , 15734-15744
A Novel Hybrid Power Supply System with Fast Response for Microprocessor
In this article, an adjustable low-impedance hybrid power supply system (ALIHPSS) is proposed for microprocessors to improve the dynamic response performance of the chip power supply. The ALIHPSS utilizes switching converters and linear converters in parallel to provide a minimum output impedance to load. Consequently, it is well-suited for scenarios requiring high-current and high-speed changes in the microprocessor's power supply system. In addition, the proposed linear converter has a simple structure and small footprint, which is conducive to increasing the power density of the hybrid power supply system. The proposed hybrid power supply system is validated on a 200-W experimental prototype. Test results indicate that the hybrid system reduces the output voltage overshoot by 46.7% and stabilization time by 27.3% compared to the conventional capacitor-only scheme.
- 29 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (12) , 15734-15744
A Novel Hybrid Power Supply System with Fast Response for Microprocessor
In this article, an adjustable low-impedance hybrid power supply system (ALIHPSS) is proposed for microprocessors to improve the dynamic response performance of the chip power supply. The ALIHPSS utilizes switching converters and linear converters in parallel to provide a minimum output impedance to load. Consequently, it is well-suited for scenarios requiring high-current and high-speed changes in the microprocessor's power supply system. In addition, the proposed linear converter has a simple structure and small footprint, which is conducive to increasing the power density of the hybrid power supply system. The proposed hybrid power supply system is validated on a 200-W experimental prototype. Test results indicate that the hybrid system reduces the output voltage overshoot by 46.7% and stabilization time by 27.3% compared to the conventional capacitor-only scheme.
- 25 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (1) , 592-609
A Novel Low-Winding-Loss Circulated Interleaving Structure for Planar Transformers Based on Current Invariance Principle
With the increase of frequency, the winding loss of planar transformers rises significantly due to the skin and proximity effects, making it one of the major contributors to converter loss. Paralleling layers is commonly adopted in high-current applications to reduce winding loss. However, the most widely used structure, symmetric interleaving, is not the minimum-loss structure according to Ferreira’s model, even though it can achieve current sharing. In this article, a new interleaving structure named circulated interleaving is proposed. This structure is invented based on the current invariance principle proposed in this paper and has only 50% loss of symmetric interleaving. The current sharing condition and the minimum winding loss of the two structures are analyzed and compared systematically by mathematical derivation. The 2D simulations validate the consistency with theory under ideal conditions and explore the variations in current distribution and losses under non-ideal conditions, demonstrating that the structure exhibits the same level of advancement under non-ideal conditions. Vias effect is also evaluated under 3D simulations, indicating only 50% inner-core winding loss compared to the symmetric interleaving. 6 transformers with different interleaving structures and different copper thickness are built and tested and the advantages of the proposed interleaving structure are validated. Practical considerations such as capacitance, leakage inductance, core shape, and heat are also discussed.
- 25 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (1) , 592-609
A Novel Low-Winding-Loss Circulated Interleaving Structure for Planar Transformers Based on Current Invariance Principle
With the increase of frequency, the winding loss of planar transformers rises significantly due to the skin and proximity effects, making it one of the major contributors to converter loss. Paralleling layers is commonly adopted in high-current applications to reduce winding loss. However, the most widely used structure, symmetric interleaving, is not the minimum-loss structure according to Ferreira’s model, even though it can achieve current sharing. In this article, a new interleaving structure named circulated interleaving is proposed. This structure is invented based on the current invariance principle proposed in this paper and has only 50% loss of symmetric interleaving. The current sharing condition and the minimum winding loss of the two structures are analyzed and compared systematically by mathematical derivation. The 2D simulations validate the consistency with theory under ideal conditions and explore the variations in current distribution and losses under non-ideal conditions, demonstrating that the structure exhibits the same level of advancement under non-ideal conditions. Vias effect is also evaluated under 3D simulations, indicating only 50% inner-core winding loss compared to the symmetric interleaving. 6 transformers with different interleaving structures and different copper thickness are built and tested and the advantages of the proposed interleaving structure are validated. Practical considerations such as capacitance, leakage inductance, core shape, and heat are also discussed.
- 27 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (6) , 6586-6590
A Method to Reduce PDN Impedance Based on Multicapacitor Loop Coupling
As the target impedance of the power delivery network decreases, the demand for output decoupling capacitors proportionally increases. Parasitic inductance of the vias connecting the output capacitors to the motherboard has a more serious impact on the impedance design of power deliver network. To solve this problem, this letter proposes a novel layout method to reduce the value of parasitic inductance associated with the vias. The proposed method utilizes the coupling effect between the vias to reduce the equivalent inductance. Therefore, the proposed method is not only simple and easy to implement, but also saves space and cost by reducing the number of decoupling capacitors. Two 200-W experimental prototypes were fabricated to compare the conventional solution with the proposed reverse coupling method. The decoupling capacitance of the prototype using the reverse-coupled structure is 25.6% lower than the prototype using conventional forward-coupled method.
- 27 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (6) , 6586-6590
A Method to Reduce PDN Impedance Based on Multicapacitor Loop Coupling
As the target impedance of the power delivery network decreases, the demand for output decoupling capacitors proportionally increases. Parasitic inductance of the vias connecting the output capacitors to the motherboard has a more serious impact on the impedance design of power deliver network. To solve this problem, this letter proposes a novel layout method to reduce the value of parasitic inductance associated with the vias. The proposed method utilizes the coupling effect between the vias to reduce the equivalent inductance. Therefore, the proposed method is not only simple and easy to implement, but also saves space and cost by reducing the number of decoupling capacitors. Two 200-W experimental prototypes were fabricated to compare the conventional solution with the proposed reverse coupling method. The decoupling capacitance of the prototype using the reverse-coupled structure is 25.6% lower than the prototype using conventional forward-coupled method.
- 7 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (8) , 9098-9109
A Current Controllable Active Transient-Voltage Compensation Circuit for Voltage Regulator Module
In this article, a novel current controllable active transient-voltage-compensation circuit (CC-ATVCC) is proposed to mitigate output voltage overshoot and undershoot in voltage regulator module (VRM) during load transients. The current difference between the VRM output and the load is compensated by field effect transistors in the proposed CC-ATVCC so that the output voltage spikes are suppressed. In the proposed CC-ATVCC, a high gain analog drive circuit, consisting of an operational amplifier cascaded with a common-source amplification circuit, provides adjustable drive voltage, which flexibly changes the compensation current. Furthermore, a time-domain model is developed in this article to analyze the interaction between VRM and the proposed CC-ATVCC, guiding the circuit design under universal conditions. Finally, the proposed CC-ATVCC has been built and tested in a 12-phase 500 A interleaved buck converter. The results show that the overshoot of the output voltage can be reduced by 34% using the proposed CC-ATVCC and the footprint of CC-ATVCC is only 10% compared with the traditional capacitor-only solution. The proposed CC-ATVCC can reduce the number of output capacitors and greatly increase the power density of VRM.
- 7 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (8) , 9098-9109
A Current Controllable Active Transient-Voltage Compensation Circuit for Voltage Regulator Module
In this article, a novel current controllable active transient-voltage-compensation circuit (CC-ATVCC) is proposed to mitigate output voltage overshoot and undershoot in voltage regulator module (VRM) during load transients. The current difference between the VRM output and the load is compensated by field effect transistors in the proposed CC-ATVCC so that the output voltage spikes are suppressed. In the proposed CC-ATVCC, a high gain analog drive circuit, consisting of an operational amplifier cascaded with a common-source amplification circuit, provides adjustable drive voltage, which flexibly changes the compensation current. Furthermore, a time-domain model is developed in this article to analyze the interaction between VRM and the proposed CC-ATVCC, guiding the circuit design under universal conditions. Finally, the proposed CC-ATVCC has been built and tested in a 12-phase 500 A interleaved buck converter. The results show that the overshoot of the output voltage can be reduced by 34% using the proposed CC-ATVCC and the footprint of CC-ATVCC is only 10% compared with the traditional capacitor-only solution. The proposed CC-ATVCC can reduce the number of output capacitors and greatly increase the power density of VRM.
- 23 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (11) , 14274-14291
2-D Analytical Copper Loss Model for PCB and Copper Foil Magnetics With Arbitrary Air Gaps
The modeling and optimization of copper losses are the basis of magnetic designs. By solving 2-D diffusion and Laplace equations, this paper proposes a 2-D analytical copper loss model for PCB inductors and transformers with arbitrary air gaps. The copper loss resistance is decoupled into skin, proximity and fringing resistances. The fringing resistance is caused by the inhomogeneity of magnetic induction expressed as the Fourier series. Based on the proposed model, some conclusions are derived theoretically. For example, fringing resistance of transformers is independent of the arrangements of primary and secondary windings, and fringing resistance increases with winding width, which could be a theoretical reason why matrix transformers should be used in some applications. The proposed model is verified by simulation with a 6.0% average error and by experiment with a 7.7% average error.
- 23 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (11) , 14274-14291
2-D Analytical Copper Loss Model for PCB and Copper Foil Magnetics With Arbitrary Air Gaps
The modeling and optimization of copper losses are the basis of magnetic designs. By solving 2-D diffusion and Laplace equations, this paper proposes a 2-D analytical copper loss model for PCB inductors and transformers with arbitrary air gaps. The copper loss resistance is decoupled into skin, proximity and fringing resistances. The fringing resistance is caused by the inhomogeneity of magnetic induction expressed as the Fourier series. Based on the proposed model, some conclusions are derived theoretically. For example, fringing resistance of transformers is independent of the arrangements of primary and secondary windings, and fringing resistance increases with winding width, which could be a theoretical reason why matrix transformers should be used in some applications. The proposed model is verified by simulation with a 6.0% average error and by experiment with a 7.7% average error.
- 19 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (12) , 14017-14022
Driving Control of GaN Devices for Transient Response Improvement of Voltage Regulator
With the continuous development of microprocessors, more stringent voltage regulation requirements have been put forward for the voltage regulators (VR) in the transient process. This letter proposes a driving control method for gallium nitride (GaN) devices to improve the transient response of the VR. When the GaN device conducts reverse, its source-drain voltage can be controlled by its gate voltage. During load step-down transient, the reverse conduction voltage of the GaN device is naturally applied across the inductor, which can be utilized to speed up the change rate of the inductor current. As a result, the overshoot of the output voltage can be reduced during load step-down transient. The proposed method does not need to modify the power circuit, and is easy to implement. Finally, the effectiveness of the proposed method is verified by experiments. The results show that the output voltage overshoot is reduced by 55%, and the transition time is shortened by 80% using the proposed method. The results also show that with the same overvoltage, using the proposed method can reduce the output capacitance by 57% and the transition time by 77%, thereby increasing the power density of the VR circuit and saving costs.
- 19 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (12) , 14017-14022
Driving Control of GaN Devices for Transient Response Improvement of Voltage Regulator
With the continuous development of microprocessors, more stringent voltage regulation requirements have been put forward for the voltage regulators (VR) in the transient process. This letter proposes a driving control method for gallium nitride (GaN) devices to improve the transient response of the VR. When the GaN device conducts reverse, its source-drain voltage can be controlled by its gate voltage. During load step-down transient, the reverse conduction voltage of the GaN device is naturally applied across the inductor, which can be utilized to speed up the change rate of the inductor current. As a result, the overshoot of the output voltage can be reduced during load step-down transient. The proposed method does not need to modify the power circuit, and is easy to implement. Finally, the effectiveness of the proposed method is verified by experiments. The results show that the output voltage overshoot is reduced by 55%, and the transition time is shortened by 80% using the proposed method. The results also show that with the same overvoltage, using the proposed method can reduce the output capacitance by 57% and the transition time by 77%, thereby increasing the power density of the VR circuit and saving costs.
- 5 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (10) , 11461-11468
A Novel Pyramid Winding for PCB Planar Inductors With Fewer Copper Layers and Lower AC Copper Loss
Relying on the advantages of small size, good controllability and consistency, PCB inductors are being widely used. For PCB inductors, reducing copper loss is one of the key issues. Although some researches focus on fringing effect in PCB planar winding, there are few methods to reduce proximity loss for PCB inductor. Regarding the issues above, this paper first improves Ferreira's one-dimensional model to accommodate the core feature of PCB winding: varying number of turns per layer. With this model, pyramid theorem is proposed that swapping the layer with fewer turns into positions farther away from the air gaps can lower the total winding losses. Based on the theorem, this manuscript proposes a novel PCB inductor winding structure named pyramid winding, which has fewer (or equal) turns on layers further from air gaps. Pyramid winding has less copper loss, fewer copper layers, smaller size and lower cost. In experiment, inductor prototypes with the same six turns and ferrite pot cores but different PCB winding arrangements are built for a 300-kHz 2700-W LLC converter. Tests on inductor resistance and converter efficiency are done and pyramid theorem and the effectiveness of pyramid winding are verified.
- 5 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (10) , 11461-11468
A Novel Pyramid Winding for PCB Planar Inductors With Fewer Copper Layers and Lower AC Copper Loss
Relying on the advantages of small size, good controllability and consistency, PCB inductors are being widely used. For PCB inductors, reducing copper loss is one of the key issues. Although some researches focus on fringing effect in PCB planar winding, there are few methods to reduce proximity loss for PCB inductor. Regarding the issues above, this paper first improves Ferreira's one-dimensional model to accommodate the core feature of PCB winding: varying number of turns per layer. With this model, pyramid theorem is proposed that swapping the layer with fewer turns into positions farther away from the air gaps can lower the total winding losses. Based on the theorem, this manuscript proposes a novel PCB inductor winding structure named pyramid winding, which has fewer (or equal) turns on layers further from air gaps. Pyramid winding has less copper loss, fewer copper layers, smaller size and lower cost. In experiment, inductor prototypes with the same six turns and ferrite pot cores but different PCB winding arrangements are built for a 300-kHz 2700-W LLC converter. Tests on inductor resistance and converter efficiency are done and pyramid theorem and the effectiveness of pyramid winding are verified.
- 14 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (4) , 3691-3696
Current Detection and Control of Synchronous Rectifier in High-Frequency LLC Resonant Converter
The synchronous rectification technology is widely used to improve the efficiency of power converters in applications with low output voltage and large current. However, it is challenging to accurately control the synchronous rectifier (SR) for high-frequency and high-current LLC converters. This letter presents a method to detect the SR current for cycle-by-cycle SR control. The resonant current and the magnetizing current are detected through magnetic coupling, and then the SR current is obtained by subtracting the two. This method requires only a few passive components and has advantages, such as high bandwidth, strong anti-interference ability, and easy implementation. This letter illustrates the working principle and implementation of the proposed method in detail and then verifies the proposed method through experiments. The proposed method can be applied to SR control in an LLC circuit, suitable for high frequency and large current situations.
- 14 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (4) , 3691-3696
Current Detection and Control of Synchronous Rectifier in High-Frequency LLC Resonant Converter
The synchronous rectification technology is widely used to improve the efficiency of power converters in applications with low output voltage and large current. However, it is challenging to accurately control the synchronous rectifier (SR) for high-frequency and high-current LLC converters. This letter presents a method to detect the SR current for cycle-by-cycle SR control. The resonant current and the magnetizing current are detected through magnetic coupling, and then the SR current is obtained by subtracting the two. This method requires only a few passive components and has advantages, such as high bandwidth, strong anti-interference ability, and easy implementation. This letter illustrates the working principle and implementation of the proposed method in detail and then verifies the proposed method through experiments. The proposed method can be applied to SR control in an LLC circuit, suitable for high frequency and large current situations.