A. O. Moskalyna
Research Subjects
A. O. Moskalyna has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- O. L. Chaika
Iron and Steel Institute of Z. I. Nekrasov NAS of Ukraine, Dnipro, Ukraine
13 shared publications - B. V. Kornilov
Iron and Steel Institute of Z. I. Nekrasov NAS of Ukraine, Dnipro, Ukraine
11 shared publications - V. V. Lebed’
Iron and Steel Institute of Z.I. Nekrasov National Academy of Sciences of Ukraine, Dnipro, Ukraine
7 shared publications Iron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine
6 shared publications- M. H. Dzhyhota4 shared publications
- M. M. Iziumskyi4 shared publications
Latest Publications
- Open Access
- 30 June 2026
- Published by Ukrainian State University of Science and Technologies
- No. 2,p. 5-14
Research of the use of hydrogen in a blast furnace under existing and prospective batch conditions
Research related to the development, implementation, and improvement of hydrogen injection technology in blast furnaces is becoming widespread worldwide, which explains the relevance of the research presented in this article. The article is devoted to analyzing the impact of hydrogen on the technical-economic, thermal, exergy, and exergo-ecological indicators of blast furnace smelting while maintaining the theoretical temperature within a rational range (1800-2300°C) with an agglomerate/pellet ratio of 79%:21% (baseline scenario) and 50%:50% (forecast scenario). The coke replacement factor for hydrogen when using hydrogen in blast furnace smelting has been established. The study was conducted using the example of the best period of operation of a blast furnace in Ukraine operating on pulverized coal fuel. The theoretical hydrogen consumption in a blast furnace was determined in this study based on the Gruner principle. The quantitative values of CO2 emissions, technical and economic, thermal energy, and exergy indicators of blast furnace smelting using hydrogen for two blast furnace operating modes were established – for agglomerate/pellet ratios of 79:21% and 50:50%.
- 30 June 2026
- Published by Ukrainian State University of Science and Technologies
- No. 2,p. 5-14
Open AccessResearch of the use of hydrogen in a blast furnace under existing and prospective batch conditions
Research related to the development, implementation, and improvement of hydrogen injection technology in blast furnaces is becoming widespread worldwide, which explains the relevance of the research presented in this article. The article is devoted to analyzing the impact of hydrogen on the technical-economic, thermal, exergy, and exergo-ecological indicators of blast furnace smelting while maintaining the theoretical temperature within a rational range (1800-2300°C) with an agglomerate/pellet ratio of 79%:21% (baseline scenario) and 50%:50% (forecast scenario). The coke replacement factor for hydrogen when using hydrogen in blast furnace smelting has been established. The study was conducted using the example of the best period of operation of a blast furnace in Ukraine operating on pulverized coal fuel. The theoretical hydrogen consumption in a blast furnace was determined in this study based on the Gruner principle. The quantitative values of CO2 emissions, technical and economic, thermal energy, and exergy indicators of blast furnace smelting using hydrogen for two blast furnace operating modes were established – for agglomerate/pellet ratios of 79:21% and 50:50%.
- 1 January 2024
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- No. 38
Analysis of existing and prospective blast furnace smelting technologies providing reduction of carbon dioxide emissions for current and prospective conditions of pig iron production in Ukraine
The article discusses the results of heat and power and exergy calculations of the possibilities of new and existing technologies for reducing carbon dioxide emissions and coke consumption, increasing pig iron production by injecting various fuel additives into the furnace – pulverised coal, hydrogen, fuel oil, natural gas, coke oven and carbon monoxide, using metal additives, increasing the blast temperature, heat losses and improving gas distribution in the blast furnace. The calculations were performed using a mathematical model of the complete energy balance of blast furnace smelting developed at the Iron and Steel Institute of National Academy of Sciences of Ukraine, and the impact of the potential of new and existing technologies on reducing CO2 emissions and technical and economic indicators of blast furnace smelting was assessed with a wide range of changes in the consumption of fuel additives and their combinations, the use of metal additives and changes in the technological parameters of the blast furnace. The study results showed that CO2 emissions in blast furnace production can be reduced by 25-30% by making changes to blast furnace technology and depend on investments, the raw material and energy base of the steelmaker, and the level of existing blast furnace technology. The influence of low-cost measures to increase blast temperature, use clean metal additives, reduce heat losses and improve gas distribution in the blast furnace on the reduction of carbon dioxide emissions and technical and economic indicators of blast furnace melting is considered. The limit values for the injection of various fuel additives into a blast furnace have been determined, which are determined by the following factors: the degree of direct reduction of iron, theoretical combustion temperature, the presence of industrial oxygen, and the temperature of the top gas. The results can be useful for determining the economic feasibility of a particular measure to reduce CO2 emissions in blast furnace production.
- 1 January 2024
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- No. 38
Analysis of existing and prospective blast furnace smelting technologies providing reduction of carbon dioxide emissions for current and prospective conditions of pig iron production in Ukraine
The article discusses the results of heat and power and exergy calculations of the possibilities of new and existing technologies for reducing carbon dioxide emissions and coke consumption, increasing pig iron production by injecting various fuel additives into the furnace – pulverised coal, hydrogen, fuel oil, natural gas, coke oven and carbon monoxide, using metal additives, increasing the blast temperature, heat losses and improving gas distribution in the blast furnace. The calculations were performed using a mathematical model of the complete energy balance of blast furnace smelting developed at the Iron and Steel Institute of National Academy of Sciences of Ukraine, and the impact of the potential of new and existing technologies on reducing CO2 emissions and technical and economic indicators of blast furnace smelting was assessed with a wide range of changes in the consumption of fuel additives and their combinations, the use of metal additives and changes in the technological parameters of the blast furnace. The study results showed that CO2 emissions in blast furnace production can be reduced by 25-30% by making changes to blast furnace technology and depend on investments, the raw material and energy base of the steelmaker, and the level of existing blast furnace technology. The influence of low-cost measures to increase blast temperature, use clean metal additives, reduce heat losses and improve gas distribution in the blast furnace on the reduction of carbon dioxide emissions and technical and economic indicators of blast furnace melting is considered. The limit values for the injection of various fuel additives into a blast furnace have been determined, which are determined by the following factors: the degree of direct reduction of iron, theoretical combustion temperature, the presence of industrial oxygen, and the temperature of the top gas. The results can be useful for determining the economic feasibility of a particular measure to reduce CO2 emissions in blast furnace production.
- 1 January 2023
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- Vol. 37
Analysis of reduction of carbon dioxide emissions from blast furnace under conditions of using advanced and existing blast furnace melting technologies
The article discusses the results of heat and power and exergy calculations of the possibilities of new and existing technologies to reduce carbon dioxide emissions and coke consumption, increase pig iron production by injecting hydrogen and hydrogen-containing fuel additives (coke and natural gas) into the furnace, using metal additives, increasing the blast temperature, heat losses, and improving gas distribution in the blast furnace. The calculations were performed using a mathematical model of the complete energy balance of blast furnace smelting developed at the Iron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine, and the impact of the potential of new and existing technologies on reducing CO2 emissions and technical and economic indicators of blast furnace smelting was assessed when the consumption of pulverized coal, hydrogen and hydrogen-containing fuel additives and their combinations in a wide range was changed. The limit values for the injection of hydrogen and hydrogen-containing fuel additives into the blast furnace horn have been determined, which are determined by the following factors: the degree of direct reduction of iron, theoretical combustion temperature, the presence of industrial oxygen, and the temperature of the furnace gas. The study results showed that CO2 emissions in blast furnace production can be reduced by 25-30% by making changes to blast furnace technology and depend on investments, the raw material and energy base of the steelmaker, and the level of existing blast furnace technology. The paper considers the impact of low-cost measures to increase the blast temperature, use of clean metal additives, reduce heat losses, and improve gas distribution in the blast furnace on the reduction of carbon dioxide emissions and technical and economic indicators of blast furnace smelting. The results can be useful for determining the economic feasibility of a particular measure to reduce CO2 emissions in blast furnace production.
- 1 January 2023
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- Vol. 37
Analysis of reduction of carbon dioxide emissions from blast furnace under conditions of using advanced and existing blast furnace melting technologies
The article discusses the results of heat and power and exergy calculations of the possibilities of new and existing technologies to reduce carbon dioxide emissions and coke consumption, increase pig iron production by injecting hydrogen and hydrogen-containing fuel additives (coke and natural gas) into the furnace, using metal additives, increasing the blast temperature, heat losses, and improving gas distribution in the blast furnace. The calculations were performed using a mathematical model of the complete energy balance of blast furnace smelting developed at the Iron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine, and the impact of the potential of new and existing technologies on reducing CO2 emissions and technical and economic indicators of blast furnace smelting was assessed when the consumption of pulverized coal, hydrogen and hydrogen-containing fuel additives and their combinations in a wide range was changed. The limit values for the injection of hydrogen and hydrogen-containing fuel additives into the blast furnace horn have been determined, which are determined by the following factors: the degree of direct reduction of iron, theoretical combustion temperature, the presence of industrial oxygen, and the temperature of the furnace gas. The study results showed that CO2 emissions in blast furnace production can be reduced by 25-30% by making changes to blast furnace technology and depend on investments, the raw material and energy base of the steelmaker, and the level of existing blast furnace technology. The paper considers the impact of low-cost measures to increase the blast temperature, use of clean metal additives, reduce heat losses, and improve gas distribution in the blast furnace on the reduction of carbon dioxide emissions and technical and economic indicators of blast furnace smelting. The results can be useful for determining the economic feasibility of a particular measure to reduce CO2 emissions in blast furnace production.
- 1 January 2023
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- Vol. 37
Analysis of the development of blast furnace blowing technologies in the 20th and 21st centuries
The article discusses the trends and classification of blast furnace blowers over the past 100 years. The development of blower technology is divided into 3 periods: The 1st period lasted until the end of the 30s of the XX century, characterized by a lack of scientific knowledge, mysticism and based on previous experience; the 2nd period - until the early 70s, when the "traditional" blower technology was mastered with one problem - difficulties with opening the first releases and simultaneous overheating of the top; the 3rd period continues today, it includes the development of new methods for intensifying heat transfer during blowing and scientific generalization of blower techniques. The main tasks of blowdown are to bring the blast furnace back to normal operation in a short time, in compliance with safety rules, without significant costs, and to preserve the blast furnace and auxiliary equipment for long-term productive operation. These tasks are closely linked to the design features of blast furnaces, including the cooling system, lining type and furnace size, which have steadily increased from less than 500 m3 to 5,600 m3. The complexity of understanding the processes of heating the charge column during the blowing period with the formation of a gas flow and a cohesion zone in it is the reason for numerous discussions about rational blowing methods: methods for calculating and placing layers of the blast furnace charge, the use of various hot blast additives (nitrogen, natural, blast furnace or coke oven gas, oxygen, steam, etc.), the rate of increase in hot blast flow and its temperature, the trend of pressure drop along the height of the charge column. The use of wood in the blast charge, the installation of constrictor rings in air tuyeres or the closure of a part of the tuyeres for blowing are discussed. Recommendations for blast furnace blowers are given. A comparison of "traditional" blowing with "progressive" blowing and blowing with nitrogen developed at the Iron and Steel Institute National Academy of Sciences of Ukraine are presented.
- 1 January 2023
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- Vol. 37
Analysis of the development of blast furnace blowing technologies in the 20th and 21st centuries
The article discusses the trends and classification of blast furnace blowers over the past 100 years. The development of blower technology is divided into 3 periods: The 1st period lasted until the end of the 30s of the XX century, characterized by a lack of scientific knowledge, mysticism and based on previous experience; the 2nd period - until the early 70s, when the "traditional" blower technology was mastered with one problem - difficulties with opening the first releases and simultaneous overheating of the top; the 3rd period continues today, it includes the development of new methods for intensifying heat transfer during blowing and scientific generalization of blower techniques. The main tasks of blowdown are to bring the blast furnace back to normal operation in a short time, in compliance with safety rules, without significant costs, and to preserve the blast furnace and auxiliary equipment for long-term productive operation. These tasks are closely linked to the design features of blast furnaces, including the cooling system, lining type and furnace size, which have steadily increased from less than 500 m3 to 5,600 m3. The complexity of understanding the processes of heating the charge column during the blowing period with the formation of a gas flow and a cohesion zone in it is the reason for numerous discussions about rational blowing methods: methods for calculating and placing layers of the blast furnace charge, the use of various hot blast additives (nitrogen, natural, blast furnace or coke oven gas, oxygen, steam, etc.), the rate of increase in hot blast flow and its temperature, the trend of pressure drop along the height of the charge column. The use of wood in the blast charge, the installation of constrictor rings in air tuyeres or the closure of a part of the tuyeres for blowing are discussed. Recommendations for blast furnace blowers are given. A comparison of "traditional" blowing with "progressive" blowing and blowing with nitrogen developed at the Iron and Steel Institute National Academy of Sciences of Ukraine are presented.
- Open Access
- 1 September 2022
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 30 (2) , 8-19
Analysis of trends in the development of ideas and technologies aimed at reducing carbon dioxide emissions in blast furnace production
- 1 September 2022
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 30 (2) , 8-19
Open AccessAnalysis of trends in the development of ideas and technologies aimed at reducing carbon dioxide emissions in blast furnace production
- 1 January 2022
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- Vol. 36
Research of the influence of technologies using PCI, natural and coke over gas on the decarbonization of the blast furnace production
The purpose of the work is to establish the patterns of use of various fuel additives aimed at reducing carbon dioxide emissions from the blast furnace. In connection with global warming and related negative consequences in the future, the issue of reducing greenhouse gases (including CO2) is one of the most important in the world. Thus, the issue of decarbonization of the metallurgical industry of Ukraine, which accounts for about 26% of emissions, is urgent. In Ukraine during steel production, CO2 emissions are ~8% higher than in EU countries, which is primarily due to the fact that the energy intensity of blast furnace production technology in Ukraine is greater. Therefore, with the introduction of quotas for CO2 emissions (EU ETS), without the introduction of blast furnace decarbonization technologies, Ukrainian metallurgy may become uncompetitive. With the use of improved thermal energy and exergy models of blast furnace smelting, regularities were established when using PCI (as the most economical substitute for coke), natural and coke over gas for CO2 emissions and technical and economic indicators of blast furnace smelting. The best period of operation of blast furnace No. 4 with a volume of 2002 m3 of PJSC "MK "Azovstal" in 2021 was chosen as the basic calculation option. The regularities of the effect of the use of different grades of coal for pulverized coal injection (PCI) and changes in the chemical composition of PCI while maintaining the theoretical combustion temperature at a constant level on CO2 emissions and blast furnace smelting indicators have been established, which will allow a rational approach to the choice of coal for PCI, which is especially relevant in wartime and the post-war recovery of Ukraine in the conditions of the loss of the coal energy base for PCI. For the first time, the critical consumption of fuel additives was determined, at which, according to Gruner's principle, it is expected to achieve full recovery of iron by indirect means, and therefore minimum fuel consumption when reaching rd close to 0%. As a result of the work performed, the limit values of the effectiveness of the use of PCI, natural and coke gas injection technologies on carbon dioxide emissions, output of secondary energy resources and coke consumption were established.
- 1 January 2022
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- Vol. 36
Research of the influence of technologies using PCI, natural and coke over gas on the decarbonization of the blast furnace production
The purpose of the work is to establish the patterns of use of various fuel additives aimed at reducing carbon dioxide emissions from the blast furnace. In connection with global warming and related negative consequences in the future, the issue of reducing greenhouse gases (including CO2) is one of the most important in the world. Thus, the issue of decarbonization of the metallurgical industry of Ukraine, which accounts for about 26% of emissions, is urgent. In Ukraine during steel production, CO2 emissions are ~8% higher than in EU countries, which is primarily due to the fact that the energy intensity of blast furnace production technology in Ukraine is greater. Therefore, with the introduction of quotas for CO2 emissions (EU ETS), without the introduction of blast furnace decarbonization technologies, Ukrainian metallurgy may become uncompetitive. With the use of improved thermal energy and exergy models of blast furnace smelting, regularities were established when using PCI (as the most economical substitute for coke), natural and coke over gas for CO2 emissions and technical and economic indicators of blast furnace smelting. The best period of operation of blast furnace No. 4 with a volume of 2002 m3 of PJSC "MK "Azovstal" in 2021 was chosen as the basic calculation option. The regularities of the effect of the use of different grades of coal for pulverized coal injection (PCI) and changes in the chemical composition of PCI while maintaining the theoretical combustion temperature at a constant level on CO2 emissions and blast furnace smelting indicators have been established, which will allow a rational approach to the choice of coal for PCI, which is especially relevant in wartime and the post-war recovery of Ukraine in the conditions of the loss of the coal energy base for PCI. For the first time, the critical consumption of fuel additives was determined, at which, according to Gruner's principle, it is expected to achieve full recovery of iron by indirect means, and therefore minimum fuel consumption when reaching rd close to 0%. As a result of the work performed, the limit values of the effectiveness of the use of PCI, natural and coke gas injection technologies on carbon dioxide emissions, output of secondary energy resources and coke consumption were established.
- 1 January 2022
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- Vol. 36
Implementation of mathematical models of material and heat balances of blast furnace smelting as part of the ACS TP of PJSC "MK "Azovstal"
On the basis of blast furnace operation data of PJSC "MK "Azovstal", an information system has been developed, which is based on mathematical models of material and heat balances of blast furnace smelting developed at the Institute of Ferrous Metallurgy of the National Academy of Sciences of Ukraine. The calculation of the material balance is carried out according to the "accounting system" of V. P. Izhevskii. The thermal energy model of I. D. Semikin is used to calculate the heat balance, which was developed for use in blast furnace production by O. V. Borodulin. The article describes the information system of calculating mathematical models. The information system allows you to calculate balances in automatic mode (collection of data from automatic control system of technological process (ACS TP) and calculation of material and heat balances for the selected period) and in manual mode (calculation of forecast periods to determine reserves for increasing the energy efficiency of blast furnace smelting). The models were adapted by calculating the material and heat balances of blast furnace melting and determining the inconsistencies. Monthly calculations of the material and heat balances of the blast furnaces were performed to adapt the models installed in the ACS TP of the blast furnace workshop of PJSC "MK "Azovstal". Inconsistencies in the overall material balances of the furnaces (the difference between the total input of materials into the furnace and smelting products) and by components (iron, carbon, etc.) were determined. It was established that when using the estimated amount of blast furnace dust at all blast furnaces of PJSC "MK "Azovstal", the amount of discrepancy between the arrival and consumption of materials lies within the credible range of error (<1,5%). Using the results of the calculation of heat balances, a comparison of the Inconsistencies of the blast furnaces was made (the ratio of the calculated indicators to the actual ones). Mathematical models of balances were implemented as part of the ACS TP of the blast furnace workshop of PJSC "MK "Azovstal" and were used to assess deviations from production norms, consumption of coke and conventional fuel, as well as forecast the possibility of improving the technical and economic indicators of smelting.
- 1 January 2022
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- Vol. 36
Implementation of mathematical models of material and heat balances of blast furnace smelting as part of the ACS TP of PJSC "MK "Azovstal"
On the basis of blast furnace operation data of PJSC "MK "Azovstal", an information system has been developed, which is based on mathematical models of material and heat balances of blast furnace smelting developed at the Institute of Ferrous Metallurgy of the National Academy of Sciences of Ukraine. The calculation of the material balance is carried out according to the "accounting system" of V. P. Izhevskii. The thermal energy model of I. D. Semikin is used to calculate the heat balance, which was developed for use in blast furnace production by O. V. Borodulin. The article describes the information system of calculating mathematical models. The information system allows you to calculate balances in automatic mode (collection of data from automatic control system of technological process (ACS TP) and calculation of material and heat balances for the selected period) and in manual mode (calculation of forecast periods to determine reserves for increasing the energy efficiency of blast furnace smelting). The models were adapted by calculating the material and heat balances of blast furnace melting and determining the inconsistencies. Monthly calculations of the material and heat balances of the blast furnaces were performed to adapt the models installed in the ACS TP of the blast furnace workshop of PJSC "MK "Azovstal". Inconsistencies in the overall material balances of the furnaces (the difference between the total input of materials into the furnace and smelting products) and by components (iron, carbon, etc.) were determined. It was established that when using the estimated amount of blast furnace dust at all blast furnaces of PJSC "MK "Azovstal", the amount of discrepancy between the arrival and consumption of materials lies within the credible range of error (<1,5%). Using the results of the calculation of heat balances, a comparison of the Inconsistencies of the blast furnaces was made (the ratio of the calculated indicators to the actual ones). Mathematical models of balances were implemented as part of the ACS TP of the blast furnace workshop of PJSC "MK "Azovstal" and were used to assess deviations from production norms, consumption of coke and conventional fuel, as well as forecast the possibility of improving the technical and economic indicators of smelting.
- Open Access
- 8 July 2021
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 29 (2) , 8-16
Analysis of the gas-dynamic operation of the furnace space and the path "blast furnace – dust collector" when changing the design of the flues
- 8 July 2021
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 29 (2) , 8-16
Open AccessAnalysis of the gas-dynamic operation of the furnace space and the path "blast furnace – dust collector" when changing the design of the flues
- 1 July 2021
- Published by Allerton Press in Steel in Translation
- Vol. 51 (7) , 468-474
Improvement of Blast Furnace Energy Efficiency by Injection of Preheated Pulverized Coal Fuel with Iron Oxides
This article discusses the improvement methods of blast furnace energy efficiency by combined injection of preheated pulverized coal fuel and iron oxides (
- 1 July 2021
- Published by Allerton Press in Steel in Translation
- Vol. 51 (7) , 468-474
Improvement of Blast Furnace Energy Efficiency by Injection of Preheated Pulverized Coal Fuel with Iron Oxides
This article discusses the improvement methods of blast furnace energy efficiency by combined injection of preheated pulverized coal fuel and iron oxides (
- 1 January 2021
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- No. 35
THE THERMAL WORK ANALYSIS OF THE FIREPLACES OF BLAST FURNACES OF UKRAINE OF VARIOUS DESIGNS
The aim of the work is to study modern ways to increase the operational reliability of the furnace and hearth of blast furnaces, which largely determine the duration of the blast furnace campaign. The article analyzes the ways to increase the stability of the furnace and hearth, presents the results of the analysis of thermal work and ignition of the lining of metal receivers of blast furnaces of different designs. The modern directions of construction of the metal receiver of blast furnaces are determined. It is shown that the modern methodology of construction of blast furnace furnaces develops two main directions: the use of a coordinated combination of refractory materials with a cooling system; use of a combination of wear-resistant materials based on carbon and ceramics. However, even the improvement of the design and cooling system of the metal receiver does not allow to fully increase the duration of the campaign. To assess the service life of the furnace, it is necessary to provide regular automated control of the ignition of the furnace lining and hearth. In Ukraine, during the renovation of blast furnaces, the design of metal receivers with the use of "ceramic glass" was preferred. To date, the system of monitoring the thermal work and ignition of the furnace has been implemented in 10 blast furnaces using the automatic control system "Horn" developed by the HMI NASU. The implementation of continuous control over the ignition of the furnace in blast furnaces allowed us to assess the effect of the use of ceramic cups. The value of heat losses of the furnace and the cost of coke for their compensation are estimated. Methods and models for determining the thermal state and wear of the metal receiver lining based on a combination of calorimetric and thermometric control methods have been developed. Comparison of heat losses of the metal receiver in the cooling system of blast furnaces allows to quantify the thermal performance of controlled areas and the furnace as a whole. It is shown that the specific value of heat loss of the metal receiver per unit volume of the blast furnace can serve as an integral parameter. It is established that the value of specific heat losses per unit volume of the blast furnace with a ceramic cup is ~ 0.4-0.7 kW/m3, which is much less than blast furnaces without it (~ 0.9-1.1 kW/m3). Ceramic glass saves coke about 1 kg/t of cast iron.
- 1 January 2021
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- No. 35
THE THERMAL WORK ANALYSIS OF THE FIREPLACES OF BLAST FURNACES OF UKRAINE OF VARIOUS DESIGNS
The aim of the work is to study modern ways to increase the operational reliability of the furnace and hearth of blast furnaces, which largely determine the duration of the blast furnace campaign. The article analyzes the ways to increase the stability of the furnace and hearth, presents the results of the analysis of thermal work and ignition of the lining of metal receivers of blast furnaces of different designs. The modern directions of construction of the metal receiver of blast furnaces are determined. It is shown that the modern methodology of construction of blast furnace furnaces develops two main directions: the use of a coordinated combination of refractory materials with a cooling system; use of a combination of wear-resistant materials based on carbon and ceramics. However, even the improvement of the design and cooling system of the metal receiver does not allow to fully increase the duration of the campaign. To assess the service life of the furnace, it is necessary to provide regular automated control of the ignition of the furnace lining and hearth. In Ukraine, during the renovation of blast furnaces, the design of metal receivers with the use of "ceramic glass" was preferred. To date, the system of monitoring the thermal work and ignition of the furnace has been implemented in 10 blast furnaces using the automatic control system "Horn" developed by the HMI NASU. The implementation of continuous control over the ignition of the furnace in blast furnaces allowed us to assess the effect of the use of ceramic cups. The value of heat losses of the furnace and the cost of coke for their compensation are estimated. Methods and models for determining the thermal state and wear of the metal receiver lining based on a combination of calorimetric and thermometric control methods have been developed. Comparison of heat losses of the metal receiver in the cooling system of blast furnaces allows to quantify the thermal performance of controlled areas and the furnace as a whole. It is shown that the specific value of heat loss of the metal receiver per unit volume of the blast furnace can serve as an integral parameter. It is established that the value of specific heat losses per unit volume of the blast furnace with a ceramic cup is ~ 0.4-0.7 kW/m3, which is much less than blast furnaces without it (~ 0.9-1.1 kW/m3). Ceramic glass saves coke about 1 kg/t of cast iron.