Burak Özdemir
Research Subjects
Burak Özdemir has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Erkan Bahçe
Department of Mechanical Engineering, Faculty of Engineering, Inönü University, 44280 Malatya, Türkiye
10 shared publications - Ender Emir
Kahramanmaras İstiklal University
3 shared publications - Ahmet Yardimeden
Department of Mechanical Engineering, Dicle University, Diyarbakir, Turkey
2 shared publications - Erol Kilickap
Dicle University
2 shared publications - Mehmet Sami Güler
Department of Machinery and Metal Technologies, Vocational School of Technical Sciences, Ordu University, Ordu, Turkey
2 shared publications Erkan Bahçe
1 shared publication
Latest Publications
- 15 March 2026
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 9 (2) , 506-515
Forecasting Initial Exit Point and Attributes of Burr Formation in Drilling of Free-Form Surfaces
The initial exit point (IEP) denotes the first location where the tool emerges from the underside of the workpiece during drilling and has a substantial influence on burr formation. This effect becomes particularly pronounced when the underside of the workpiece is not flat. In such cases, unfavorable IEP positioning may lead to increased burr height, unstable material separation, and non-uniform exit deformation, thereby deteriorating surface quality and increasing the need for secondary deburring operations. The IEP, together with the tool initial position (TIP), is governed by the tool’s starting placement, workpiece thickness, feed rate, and spindle speed, all of which are highly adjustable parameters. In this study, burr formation during the drilling of a B-spline free-form surface was investigated by mathematically modeling the tool cutting edge tip with respect to the IEP. The proposed model was developed in the MATLAB environment and experimentally validated on a workpiece containing a B-spline surface. The results demonstrate that accurate prediction and control of the IEP enable effective regulation of burr formation on free-form surfaces. By optimizing drilling parameters, burr height was significantly reduced, achieving an average decrease of 27.8% when the exit occurred near the tool tip region compared to exits between the tip and diameter edge. These findings highlight both the critical role of the IEP in burr generation and the necessity of its careful control in drilling operations on non-flat surfaces.
- 15 March 2026
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 9 (2) , 506-515
Forecasting Initial Exit Point and Attributes of Burr Formation in Drilling of Free-Form Surfaces
The initial exit point (IEP) denotes the first location where the tool emerges from the underside of the workpiece during drilling and has a substantial influence on burr formation. This effect becomes particularly pronounced when the underside of the workpiece is not flat. In such cases, unfavorable IEP positioning may lead to increased burr height, unstable material separation, and non-uniform exit deformation, thereby deteriorating surface quality and increasing the need for secondary deburring operations. The IEP, together with the tool initial position (TIP), is governed by the tool’s starting placement, workpiece thickness, feed rate, and spindle speed, all of which are highly adjustable parameters. In this study, burr formation during the drilling of a B-spline free-form surface was investigated by mathematically modeling the tool cutting edge tip with respect to the IEP. The proposed model was developed in the MATLAB environment and experimentally validated on a workpiece containing a B-spline surface. The results demonstrate that accurate prediction and control of the IEP enable effective regulation of burr formation on free-form surfaces. By optimizing drilling parameters, burr height was significantly reduced, achieving an average decrease of 27.8% when the exit occurred near the tool tip region compared to exits between the tip and diameter edge. These findings highlight both the critical role of the IEP in burr generation and the necessity of its careful control in drilling operations on non-flat surfaces.
- 20 January 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 240 (4) , 4666-4675
Mechanical strength properties of integrated holes and drilled PLA lattice structures
This study examined the mechanical properties of components produced by additive manufacturing (AM) using polylactic acid material in connection with drilling procedures. The components were manufactured using two different techniques: one involving integrated holes and the other with holes drilled afterward. Samples with octet truss lattice designs underwent an embedment specimen strength test following their assembly. Following the test, the average maximum compressive stress in the integrated samples was measured at 435.66 N, whereas the drilled samples had a value of 145 N. Cross-sectional images of the internal cavity were obtained prior to and following the embedment specimen strength test to examine lattice structure deformation. The deformation characteristics of the bolt connection segment were examined utilizing the images captured during the embedment specimen strength test.
- 20 January 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 240 (4) , 4666-4675
Mechanical strength properties of integrated holes and drilled PLA lattice structures
This study examined the mechanical properties of components produced by additive manufacturing (AM) using polylactic acid material in connection with drilling procedures. The components were manufactured using two different techniques: one involving integrated holes and the other with holes drilled afterward. Samples with octet truss lattice designs underwent an embedment specimen strength test following their assembly. Following the test, the average maximum compressive stress in the integrated samples was measured at 435.66 N, whereas the drilled samples had a value of 145 N. Cross-sectional images of the internal cavity were obtained prior to and following the embedment specimen strength test to examine lattice structure deformation. The deformation characteristics of the bolt connection segment were examined utilizing the images captured during the embedment specimen strength test.
- Open Access
- 1 January 2025
- Published by Dicle Universitesi Muhendislik Fakultesi Muhendislik Dergisi in Dicle Üniversitesi Mühendislik Fakültesi Mühendislik Dergisi
- Vol. 16 (1) , 177-184
Karbon fiber kaplamalı tpms kafes yapılarının basma testi analizi
Eklemeli imalat, karmaşık geometrilere sahip hafif ve yüksek performanslı yapılar üretme imkânı sunan yenilikçi bir üretim teknolojisidir. Bu teknolojinin öne çıkan uygulamalarından biri olan Triply Periodic Minimal Surface (TPMS) yapılar, düşük yoğunluk, yüksek yüzey alanı, enerji emilimi ve mekanik dayanım gibi avantajlar sağlamaktadır. Ancak, eklemeli imalatla üretilen TPMS yapılarının mekanik dayanımı, uygulama gereksinimlerini karşılamakta yetersiz kalabilmektedir. Bu bağlamda karbon fiber kaplama, TPMS yapılarının mekanik dayanımını ve sertliğini artırarak yük taşıma kapasitesini iyileştiren etkili bir çözüm olarak öne çıkmaktadır.Bu çalışma, karbon fiber kaplamalı TPMS kafes yapılarının mekanik performansını incelemiş ve farklı geometrik tasarımların enerji emme kapasitesi, yük taşıma dayanımı ve elastik modül üzerindeki etkilerini değerlendirmiştir. Octet geometrisi, 1250 J enerji emme kapasitesi ve 500 N maksimum yük taşıma dayanımı ile en yüksek performansı sergilerken, elastik modül açısından diğer geometrilere kıyasla daha düşük bir değer göstermiştir. HMK (1100 J, 450 N), YMK (950 J, 400 N) ve Elmas (850 J, 350 N) geometrileri ise dengeli performanslarıyla farklı uygulama alanları için uygun seçenekler sunmaktadır.Sonuç olarak, karbon fiber kaplama, TPMS yapılarının mekanik özelliklerini optimize ederek havacılık, otomotiv, biyomedikal ve enerji gibi sektörlerde hafiflik, dayanıklılık ve çok işlevlilik gerektiren uygulamalarda geniş bir kullanım potansiyeli sunmaktadır.
- 1 January 2025
- Published by Dicle Universitesi Muhendislik Fakultesi Muhendislik Dergisi in Dicle Üniversitesi Mühendislik Fakültesi Mühendislik Dergisi
- Vol. 16 (1) , 177-184
Open AccessKarbon fiber kaplamalı tpms kafes yapılarının basma testi analizi
Eklemeli imalat, karmaşık geometrilere sahip hafif ve yüksek performanslı yapılar üretme imkânı sunan yenilikçi bir üretim teknolojisidir. Bu teknolojinin öne çıkan uygulamalarından biri olan Triply Periodic Minimal Surface (TPMS) yapılar, düşük yoğunluk, yüksek yüzey alanı, enerji emilimi ve mekanik dayanım gibi avantajlar sağlamaktadır. Ancak, eklemeli imalatla üretilen TPMS yapılarının mekanik dayanımı, uygulama gereksinimlerini karşılamakta yetersiz kalabilmektedir. Bu bağlamda karbon fiber kaplama, TPMS yapılarının mekanik dayanımını ve sertliğini artırarak yük taşıma kapasitesini iyileştiren etkili bir çözüm olarak öne çıkmaktadır.Bu çalışma, karbon fiber kaplamalı TPMS kafes yapılarının mekanik performansını incelemiş ve farklı geometrik tasarımların enerji emme kapasitesi, yük taşıma dayanımı ve elastik modül üzerindeki etkilerini değerlendirmiştir. Octet geometrisi, 1250 J enerji emme kapasitesi ve 500 N maksimum yük taşıma dayanımı ile en yüksek performansı sergilerken, elastik modül açısından diğer geometrilere kıyasla daha düşük bir değer göstermiştir. HMK (1100 J, 450 N), YMK (950 J, 400 N) ve Elmas (850 J, 350 N) geometrileri ise dengeli performanslarıyla farklı uygulama alanları için uygun seçenekler sunmaktadır.Sonuç olarak, karbon fiber kaplama, TPMS yapılarının mekanik özelliklerini optimize ederek havacılık, otomotiv, biyomedikal ve enerji gibi sektörlerde hafiflik, dayanıklılık ve çok işlevlilik gerektiren uygulamalarda geniş bir kullanım potansiyeli sunmaktadır.
- 31 August 2024
- Published by Van Yuzuncu Yil University in Yüzüncü Yıl Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 29 (2) , 708-719
Investigation of Delamination in the Drilling of PLA Specimens with Different Lattice Structures
Aim of this study examines the impact of processing parameters and lattice structures on delamination during the drilling of cylinder PLA (Polylactic acid) parts. The parts were designed with four different lattice structures (gyroid, I-WP, nevoius, and diamond) and produced using a 3D printer. A 5 mm HSS drill was used to drill from the center point. After drilling, images of the entrance and exit holes were captured using a digital microscope. The delamination, burr, and circularity around the hole were analyzed. The results showed that the Gyroid and I-WP lattice structures had the lowest delamination at the entrance and exit holes. No burr was observed at the entrance of the specimens. The Nevoius lattice structure exhibited the lowest burr value at the hole exit and entrance, as well as the lowest exit circularity deviation. Among the samples, the highest delamination was observed at the hole entrance in I-WP (0.5601), while the lowest delamination was observed in Gyroid (0.5423). At the hole exit, the highest delamination was observed in Gyroid (0.6229), and the lowest delamination was observed in I-WP (0.5426).
- 31 August 2024
- Published by Van Yuzuncu Yil University in Yüzüncü Yıl Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 29 (2) , 708-719
Investigation of Delamination in the Drilling of PLA Specimens with Different Lattice Structures
Aim of this study examines the impact of processing parameters and lattice structures on delamination during the drilling of cylinder PLA (Polylactic acid) parts. The parts were designed with four different lattice structures (gyroid, I-WP, nevoius, and diamond) and produced using a 3D printer. A 5 mm HSS drill was used to drill from the center point. After drilling, images of the entrance and exit holes were captured using a digital microscope. The delamination, burr, and circularity around the hole were analyzed. The results showed that the Gyroid and I-WP lattice structures had the lowest delamination at the entrance and exit holes. No burr was observed at the entrance of the specimens. The Nevoius lattice structure exhibited the lowest burr value at the hole exit and entrance, as well as the lowest exit circularity deviation. Among the samples, the highest delamination was observed at the hole entrance in I-WP (0.5601), while the lowest delamination was observed in Gyroid (0.5423). At the hole exit, the highest delamination was observed in Gyroid (0.6229), and the lowest delamination was observed in I-WP (0.5426).
- 1 July 2023
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 6 (3) , 229-234
Sıcak Pres CETP Kompozit Panellerin Eğilme Performansları Üzerine Deneysel ve Teorik Çalışmalar
Bu çalışmada, sıcak pres yöntemi ile üretilmiş CETP (Cam elyaf takviyeli polimerler) kompozit panellerin eğilme performansları araştırılmıştır. Bu amaçla cam elyaf ve reçine ile hazırlanmış kompozit plakalar belli bir sıcaklık ve basınç altında preslenerek panellere çevrilmiştir. Üretilen paneller değişken yükler altında çalışan malzemeler olması nedeni ile eğilme testine tabi tutulmuştur. Panellerden 14×150×6 mm3 ebatlarında numuneler alınarak üç nokta eğilme testi uygulamıştır. Deneyin doğrulanması ve gerilme dağılımının görsel olarak incelenebilmesi amacıyla sonlu elemanlar analizi (SEA) yapılmıştır. Çalışma sonunda deneysel ve teorik sonuçlar karşılaştırılmış ve uygulanan yüklerin etkileri tartışılmıştır. Deneylerde en yüksek eğilme gerilmesi 150.39 MPa, SE analizinde ise 164.31 MPa şeklinde gerçekleşmiştir. Malzemenin hasar öncesi deplasmanı deney ve SEA için sırasıyla 4.92 mm ve 5.46 mm’dir. Deney ve SEA sonuçlarının birbirine yakın sonuçlar verdiği görülmüştür. Elde edilen sonuçlar CETP kompozit malzemelerin farklı alanlarda kullanımı öncesi boyut ve mekanik özelliklerin belirlenmesi çalışmalarına destek olacak niteliktedir.
- 1 July 2023
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 6 (3) , 229-234
Sıcak Pres CETP Kompozit Panellerin Eğilme Performansları Üzerine Deneysel ve Teorik Çalışmalar
Bu çalışmada, sıcak pres yöntemi ile üretilmiş CETP (Cam elyaf takviyeli polimerler) kompozit panellerin eğilme performansları araştırılmıştır. Bu amaçla cam elyaf ve reçine ile hazırlanmış kompozit plakalar belli bir sıcaklık ve basınç altında preslenerek panellere çevrilmiştir. Üretilen paneller değişken yükler altında çalışan malzemeler olması nedeni ile eğilme testine tabi tutulmuştur. Panellerden 14×150×6 mm3 ebatlarında numuneler alınarak üç nokta eğilme testi uygulamıştır. Deneyin doğrulanması ve gerilme dağılımının görsel olarak incelenebilmesi amacıyla sonlu elemanlar analizi (SEA) yapılmıştır. Çalışma sonunda deneysel ve teorik sonuçlar karşılaştırılmış ve uygulanan yüklerin etkileri tartışılmıştır. Deneylerde en yüksek eğilme gerilmesi 150.39 MPa, SE analizinde ise 164.31 MPa şeklinde gerçekleşmiştir. Malzemenin hasar öncesi deplasmanı deney ve SEA için sırasıyla 4.92 mm ve 5.46 mm’dir. Deney ve SEA sonuçlarının birbirine yakın sonuçlar verdiği görülmüştür. Elde edilen sonuçlar CETP kompozit malzemelerin farklı alanlarda kullanımı öncesi boyut ve mekanik özelliklerin belirlenmesi çalışmalarına destek olacak niteliktedir.
- Open Access
- 15 June 2023
- Published by Karadeniz Fen Bilimleri Dergisi in Karadeniz Fen Bilimleri Dergisi
- Vol. 13 (2) , 483-492
Investigation of the Effect of Feed Rate on Vibration in Aluminum Milling
Bu çalışmada, frezeleme işleminde ilerleme hızı parametresinin etkileri araştırılmıştır. Bu amaçla Al7075 malzemesi diğer işleme parametreleri sabit tutularak 0.1, 0.15, 0.2, 0.25 ve 0.3 mm/dev ilerleme hızları ile frezelenmiştir. Her bir ilerleme değeri için parça boyunca kanal frezeleme yapılmıştır. Frezeleme sırasında iş parçasında bağlı cihaz ile titreşim ölçülmüştür. Titreşim değerleri istatistiksel olarak değerlendirilmiş ve ilerlemenin titreşime etkisi tartışılmıştır. Titreşim ölçümünden elde edilen verilere göre genel olarak, sabit devirde ilerlemenin artışı titreşimi azaltmıştır. Takımın kesme kabiliyetinin azalması ile verilerin standart sapması artmış ve daha düzensiz bir titreşim seyri tespit edilmiştir. Elde edilen sonuçlar frezelemede optimum ilerleme değeri belirleme çalışmalarına destek olacak niteliktedir.
- 15 June 2023
- Published by Karadeniz Fen Bilimleri Dergisi in Karadeniz Fen Bilimleri Dergisi
- Vol. 13 (2) , 483-492
Open AccessInvestigation of the Effect of Feed Rate on Vibration in Aluminum Milling
Bu çalışmada, frezeleme işleminde ilerleme hızı parametresinin etkileri araştırılmıştır. Bu amaçla Al7075 malzemesi diğer işleme parametreleri sabit tutularak 0.1, 0.15, 0.2, 0.25 ve 0.3 mm/dev ilerleme hızları ile frezelenmiştir. Her bir ilerleme değeri için parça boyunca kanal frezeleme yapılmıştır. Frezeleme sırasında iş parçasında bağlı cihaz ile titreşim ölçülmüştür. Titreşim değerleri istatistiksel olarak değerlendirilmiş ve ilerlemenin titreşime etkisi tartışılmıştır. Titreşim ölçümünden elde edilen verilere göre genel olarak, sabit devirde ilerlemenin artışı titreşimi azaltmıştır. Takımın kesme kabiliyetinin azalması ile verilerin standart sapması artmış ve daha düzensiz bir titreşim seyri tespit edilmiştir. Elde edilen sonuçlar frezelemede optimum ilerleme değeri belirleme çalışmalarına destek olacak niteliktedir.
- 1 April 2023
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 6 (2) , 68-73
Cam Elyaf Takviyeli Polimer Kompozitlerin Delmesinde Takım Çapının İtme Kuvveti ve Titreşim Üzerindeki Etkisinin Araştırılması
Bu çalışmada, CETP (Cam Elyaf Takviyeli Polimer) kompozit malzemenin delinmesinde takım çapının oluşan itme kuvveti ve titreşim üzerine etkileri incelenmiştir. Bu amaçla CETP plaka diğer delme parametreleri sabit tutularak 5, 7,5 ve 10 mm çapında takımlarla delinmiştir. Delme süresince itme kuvveti ve titreşim ölçümü yapılmıştır. Elde edilen verilerin istatistiksel analizi sonucunda takım çapının artışı ile itme kuvvetinin arttığı ve titreşimin azaldığı görülmüştür. Ayrıca daha yüksek çaplarda takımın daha düşük salınım gösterdiği ve kararlı bir delme işlemi yaptığı tespit edilmiştir. Çalışmanın, CETP kompozit malzemelerde uygun delik kalitesini sağlayacak takım çapı seçimi için yol gösterici olması beklenmektedir. Bununla birlikte itme kuvveti ve titreşimin olumsuz etkilerini tespit noktasında araştırmacılara destek sunacaktır.
- 1 April 2023
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 6 (2) , 68-73
Cam Elyaf Takviyeli Polimer Kompozitlerin Delmesinde Takım Çapının İtme Kuvveti ve Titreşim Üzerindeki Etkisinin Araştırılması
Bu çalışmada, CETP (Cam Elyaf Takviyeli Polimer) kompozit malzemenin delinmesinde takım çapının oluşan itme kuvveti ve titreşim üzerine etkileri incelenmiştir. Bu amaçla CETP plaka diğer delme parametreleri sabit tutularak 5, 7,5 ve 10 mm çapında takımlarla delinmiştir. Delme süresince itme kuvveti ve titreşim ölçümü yapılmıştır. Elde edilen verilerin istatistiksel analizi sonucunda takım çapının artışı ile itme kuvvetinin arttığı ve titreşimin azaldığı görülmüştür. Ayrıca daha yüksek çaplarda takımın daha düşük salınım gösterdiği ve kararlı bir delme işlemi yaptığı tespit edilmiştir. Çalışmanın, CETP kompozit malzemelerde uygun delik kalitesini sağlayacak takım çapı seçimi için yol gösterici olması beklenmektedir. Bununla birlikte itme kuvveti ve titreşimin olumsuz etkilerini tespit noktasında araştırmacılara destek sunacaktır.
- 10 March 2023
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 39 (1) , 55-68
Optimization of parameters for drilling composite materials with freeform surfaces
In the drilling process, the angle of surface is one of the parameters that affect hole quality. In study, the effects of feed rate, spindle speed and surface angle on the thrust force, roughness, and delamination, which are the factors affecting the quality of hole, were investigated in the drilling of GFRP (glass fiber reinforced polymer) and CFRP (carbon fiber reinforced polymer) with freeform surfaces. With ANOVA (Analysis of Variance) and regression analysis, the parameter effects were statistically compared, and descriptive mathematical models were derived. The mathematical models were subjected to the Genetic Algorithm approach according to the different surface angles determined and the optimum parameter values were calculated. Guiding data were obtained about the effects of machining on hole quality in drilling composite at different surface angles, which is the main motivation of the study. Optimization results will improve hole quality on curved surfaces, while saving cost and time. Graphical Abstract
- 10 March 2023
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 39 (1) , 55-68
Optimization of parameters for drilling composite materials with freeform surfaces
In the drilling process, the angle of surface is one of the parameters that affect hole quality. In study, the effects of feed rate, spindle speed and surface angle on the thrust force, roughness, and delamination, which are the factors affecting the quality of hole, were investigated in the drilling of GFRP (glass fiber reinforced polymer) and CFRP (carbon fiber reinforced polymer) with freeform surfaces. With ANOVA (Analysis of Variance) and regression analysis, the parameter effects were statistically compared, and descriptive mathematical models were derived. The mathematical models were subjected to the Genetic Algorithm approach according to the different surface angles determined and the optimum parameter values were calculated. Guiding data were obtained about the effects of machining on hole quality in drilling composite at different surface angles, which is the main motivation of the study. Optimization results will improve hole quality on curved surfaces, while saving cost and time. Graphical Abstract
- Open Access
- 28 December 2022
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 20 (1)
Analysis of Drilling Behaviour in Jute Fibres Reinforced Natural Composites
In the study, Natural jute composite materials, which have environmental advantages due to their easily degradable nature were drilled with different processing parameters and the effects of thrust force, vibration and temperature changes on hole quality were investigated. The effect of feed and spindle speed was statistically analyzed using ANOVA method. The thrust force, vibration and temperature factors that occur depending on the drilling parameters vary and affect the roughness and delamination values. The effect of feed and speed on thrust force was calculated as 97.87% and the feed effect (90.85%) is far greater than the speed (9.15%). The effect of drilling parameters on vibration is statistically insignificant due to the different spread behavior in the layers of the composite material (R2 = 0.2329). However, feed effect on vibration (94.6%) is greater than the speed effect (6.06%). The temperature is affected by 96.93% of the drilling parameters and the speed is 84.16% and the feed is 15.83%. The roughness effect depending on the drilling parameters is measured as 84.91%. The effect of speed on roughness (90.26%) is greater than the feed (9.73%). It has been determined that this situation is mostly related to vibration and temperature.
- 28 December 2022
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 20 (1)
Open AccessAnalysis of Drilling Behaviour in Jute Fibres Reinforced Natural Composites
In the study, Natural jute composite materials, which have environmental advantages due to their easily degradable nature were drilled with different processing parameters and the effects of thrust force, vibration and temperature changes on hole quality were investigated. The effect of feed and spindle speed was statistically analyzed using ANOVA method. The thrust force, vibration and temperature factors that occur depending on the drilling parameters vary and affect the roughness and delamination values. The effect of feed and speed on thrust force was calculated as 97.87% and the feed effect (90.85%) is far greater than the speed (9.15%). The effect of drilling parameters on vibration is statistically insignificant due to the different spread behavior in the layers of the composite material (R2 = 0.2329). However, feed effect on vibration (94.6%) is greater than the speed effect (6.06%). The temperature is affected by 96.93% of the drilling parameters and the speed is 84.16% and the feed is 15.83%. The roughness effect depending on the drilling parameters is measured as 84.91%. The effect of speed on roughness (90.26%) is greater than the feed (9.73%). It has been determined that this situation is mostly related to vibration and temperature.
- 19 November 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 237 (11) , 1716-1725
Prediction of tool deflection using image processing in ball-end milling
In milling, some of the factors that contribute to the poor quality of products are the cutting forces. Depending on the machining parameters, the cutting forces may significantly affect the tool being used in the machining process. Tool deflection can be modeled as bending deformation. Tool deflection causes poor surface quality, geometrical and dimensional errors. For this reason, it must be addressed during milling and reduced by changing the machining parameters. In the determination of tool deflection, force-based analytical and finite element methods (FEM) and sensor measurement methods are widely used. These technologies have drawbacks such as not being able to obtain fast data, being expensive, demanding precise control, and requiring continual calibration. This study aims to determine the deflection of the tool by image processing dependent on the tool/material pair and machining parameters in the milling process. For this purpose, the AL7075 material with a free-form surface was machined on a CNC milling machine. A mathematical equation is proposed to estimate the tool deflection based on the image processing results. The method has shown that tool deviation can be detected more quickly and simply by image processing.
- 19 November 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 237 (11) , 1716-1725
Prediction of tool deflection using image processing in ball-end milling
In milling, some of the factors that contribute to the poor quality of products are the cutting forces. Depending on the machining parameters, the cutting forces may significantly affect the tool being used in the machining process. Tool deflection can be modeled as bending deformation. Tool deflection causes poor surface quality, geometrical and dimensional errors. For this reason, it must be addressed during milling and reduced by changing the machining parameters. In the determination of tool deflection, force-based analytical and finite element methods (FEM) and sensor measurement methods are widely used. These technologies have drawbacks such as not being able to obtain fast data, being expensive, demanding precise control, and requiring continual calibration. This study aims to determine the deflection of the tool by image processing dependent on the tool/material pair and machining parameters in the milling process. For this purpose, the AL7075 material with a free-form surface was machined on a CNC milling machine. A mathematical equation is proposed to estimate the tool deflection based on the image processing results. The method has shown that tool deviation can be detected more quickly and simply by image processing.