EEEnder Emir

Ender Emir

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ender Emir has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Investigation of drilling performance of PLA samples produced at different raster angles using the FDM method

    by Ender Emir

    Additive manufacturing (AM) is an innovative production technology used to create parts using a layer-by-layer production method. The Fused Deposition Modeling (FDM) AM technique is particularly preferred due to its ability to provide flexible production and the availability of inexpensive materials. This method is frequently used in the automotive industry, medical and biomedical applications, and prototype production. However, despite its flexible production capabilities, it requires specific processing steps to improve post-production surface quality and dimensional accuracy. As a result of these processes, undesirable outcomes such as delamination, surface roughness, and high temperature formation may occur, depending on both the processing parameters and the production parameters. Therefore, it is necessary to examine both the AM production parameters and the processing parameters. The aim of this study is to examine the drilling performance of samples produced at different raster angles using the FDM technique made from polylactic acid (PLA) material. Therefore, three different samples were produced at raster angles of 0-45-90° and drilled at three different feed rates (0.1-0.15-0.2 mm/rev). The thrust force, delamination, temperature formation, and surface roughness changes were examined. The results showed that the thrust force increased with the increase in feed rate and raster angle, which in turn led to an increase in the amount of delamination. The increase in raster angle and feed rate also raised the temperature during drilling. Additionally, chips became wrapped around the chip evacuation channels of the cutting tool, and as the cutting tool attempted to push and remove the chips, it increased the surface roughness of the hole’s inner walls. Finally, the relationship between the dependent and independent variables in the experimental results was examined using ANOVA analysis, and it was found that the effects of feed rate and raster angle on thrust force were significant ( p < 0.05).

  • Estimation of Forces in Longitudinal and Multi-Pass Milling of GFRP and ABACA Composites Utilizing Machine Learning Techniques

    by Burak Özdemir, Ender Emir, Erkan Bahçe, Ahmet Yardımeden, Erol Kılıçkap

    In this study, workpieces made of glass fibre reinforced polymer and ABACA composite materials were machined by longitudinal and multi-pass milling methods with three different feed and speed parameters. The effect of milling methods on the finish surface was discussed through microscope images. The effect of machining parameters on the force was analysed by measuring the force values changing during machining. For this purpose, advanced prediction modelling was performed with the Random forest machine learning method. The effect of machining methods and parameters on cutting force is predicted with an average success rate of 86%. The primary contribution of this research lies in providing a comparative assessment of natural and polymer composites under distinct milling conditions and introducing a data-driven approach for accurate cutting-force prediction. The findings provide new insights into the processing of natural fibre composites as an alternative to polymer composites in milling.


  • An ANFIS model for predicting workpiece deformation during the milling of thin-walled composite components

    by Burak Özdemir, Ender Emir, Erkan Bahçe, Ahmet Yardımeden, Erol Kılıçkap

    The milling of thin-walled structural components is a meticulous procedure, particularly for workpieces with diminished mechanical qualities. Such workpieces are subject to greater deformation due to the cutting force. These deformations have a negative effect on the machining accuracy of the machined parts. Therefore, it is important to focus on the causes and effects of workpiece deformation in order to understand the surface machining quality of the workpiece. The aim of this study is to calculate the deflection of the workpiece during milling of thin-walled components made of glass fiber reinforced polymer composite (GFRP), carbon fiber reinforced polymer composite (CFRP) and basalt fiber reinforced polymer composite (BFRP). The tests were carried out at three different feed rates (0.1-0.2-0.3 mm/rev) and three different speeds (2000-3000-4000 r/min). A high-speed camera was used to detect the deflection of the thin-walled workpiece during milling. The effect of machining parameters on the variation of cutting force and deflection was statistically evaluated by analysis of variance. In order to better understand the behaviour of the parameters in the process, a predictive model was created using the artificial intelligence method Adaptive Network Based Fuzzy Inference System (ANFIS). The model is able to predict the cutting force with an accuracy of 65.7% and the deformation with an accuracy of 98.9%.


  • Examining the impact of fiber orientation angle and drilling parameters on the quality of holes in GFRP pipes

    by Burak Ozdemir, Ender Emir, Erkan Bahce, Ahmet Yardimeden, Erol Kilickap

    This study examined the impact of altering the fiber orientation angle on delamination and surface quality in glass fiber reinforced polymer (GFRP) pipes. GFRP pipes are manufactured at three distinct orientation angles: 30°, 60°, and 90°. Experiments were conducted at four distinct feed rates (0.05, 0.1, 0.2, 0.3 mm/rev) at three varying speeds (2000, 4000, 6000 rpm). The impact of the fiber orientation angle on thrust force, entry and exit delamination, and surface roughness of the holes was examined. The orientation angle significantly affected other parameters ( p < 0.05). An orientation angle of 90° generated increased thrust force while reducing roughness and delamination in comparison to other orientation angles. At a 90° orientation angle relative to 30° and 60°, an approximate increase in thrust force of 4.8%–4.1%, a decrease in surface roughness of 25%–21%, and a decrease in delamination of 23%–7% was observed.


  • Open Access

    Investigation of Burr Formation and Circularity Error in Drilling of PLA Produced at Different Printing Temperatures with Machine Learning-Based Prediction

    by Ender Emir

    In this study, it was aimed to investigate the effect of feed (0.1-0.15-0.2 mm/rev) and printing temperature (190-210-230°C) on the formation of burrs and circularity in the drilling of samples produced using polylactic acid (PLA) material with the fused deposition modelling (FDM) technique, which is an additive manufacturing (AM) method. In the results obtained, it was observed that the burr height increased with the increase of the feed in the drilling of the samples, and the burr height decreased with the increase of the printing temperature. The maximum burr height at the hole entrance was 0.32 mm (0.2 mm/rev, 190°C), while the maximum burr height at the hole exit was 0.37 mm (0.2 mm/rev, 190°C). The maximum circularity deviation at the hole entrance was 0.15 mm (0.2 mm/rev, 230°C) and the maximum circularity deviation at the hole exit was 0.1 mm (0.2 mm/rev, 190°C). In addition, prediction modelling for burr height and deviation from circularity was performed with an average success rate of R2 94%.

  • Open Access

    Compressive behavior of functional graded hybrid lattice structure

    by Ender Emir, Erkan Bahçe

    Today, lattice structures are preferred in various fields, including biomedical, aviation, and the defense industry, due to their exceptional mechanical properties, low density, high specific strength, high specific stiffness, good energy absorption ability, and excellent thermal and acoustic insulation. This study focused on investigating the mechanical performance of functionally graded hybrid (FGH) lattice structures. Three types of lattice structures were designed: triple periodic minimal surface (TPMS)-based primitive-gyroid (P-G); body-centered cubic-gyroid (BCC-G); and primitive-body centered cubic (P-BCC) hybrid lattice structures. In addition, each hybrid lattice structure was formed both in the large porosity size and in the production direction from the large pore size to the small pore size. These hybrid lattice structures were then fabricated using selective laser melting (SLM). In the results of compression tests on FGH lattice structures with large pore sizes, the P-BCC structure exhibited the highest elastic modulus among the test specimens, measuring 1573.17 MPa. The highest yield strength was found to be 128.46 MPa in the BCC-G hybrid lattice structure. Furthermore, when evaluating the energy absorption capabilities of hybrid lattice structures with a large pore size, the BCC-G structure demonstrated the highest resilience and toughness among the test samples. On the other hand, an increase in elastic modulus, yield strength, and energy absorption values was observed with the decrease in pore size. However, it was observed that the change in pore size due to defects in the production of lattice structures is another effective parameter on mechanical properties. This study suggests that desired mechanical properties can be achieved through the functional grading of pore size and the creation of hybrid structures utilizing different lattice designs.


  • Investigation of Delamination in the Drilling of PLA Specimens with Different Lattice Structures

    by Ender Emir, Burak Özdemir, Erkan Bahçe, Gözde Erener

    Aim of this study examines the impact of processing parameters and lattice structures on delamination during the drilling of cylinder PLA (Polylactic acid) parts. The parts were designed with four different lattice structures (gyroid, I-WP, nevoius, and diamond) and produced using a 3D printer. A 5 mm HSS drill was used to drill from the center point. After drilling, images of the entrance and exit holes were captured using a digital microscope. The delamination, burr, and circularity around the hole were analyzed. The results showed that the Gyroid and I-WP lattice structures had the lowest delamination at the entrance and exit holes. No burr was observed at the entrance of the specimens. The Nevoius lattice structure exhibited the lowest burr value at the hole exit and entrance, as well as the lowest exit circularity deviation. Among the samples, the highest delamination was observed at the hole entrance in I-WP (0.5601), while the lowest delamination was observed in Gyroid (0.5423). At the hole exit, the highest delamination was observed in Gyroid (0.6229), and the lowest delamination was observed in I-WP (0.5426).


  • Investigation of the mechanical properties triple periodic minimal surfaces lattice structures with functional graded of porosity

    by Ender Emir, Erkan Bahçe

    In recent years, triple periodic minimal surfaces (TPMS) have attracted attention in many applications such as biomaterials, aerospace, defense industry etc. lightweight components with high strength and functionally graded material (FGM). In particular, the mechanical properties and deformation behavior of these structures under load should be examined. In this study, it was aimed to evaluate the manufacturability and mechanical performance of fixed pore size and functional graded porosity (FGP) lattice structures produced by fused deposition modelling (FDM) method. TPMS primitive and gyroid lattice structures designed in the dimensions of 20 × 20 × 20 mm with fixed 20% pore size and functional graded (FG) from 20% to 40% pore size were used in the experiments. In order to reveal the effects of pore size on mechanical performance, uniaxial compression tests were carried out. In addition, for the validation of the experimental results, compression tests with the finite element method (FEM) were simulated for each sample. In the two different pore size changes tested in the study, the gyroid lattice structure showed the highest mechanical performance compared to the primitive lattice structure. In addition, the FEM results were in good agreement with the experimental results.


  • Optimization of parameters for drilling composite materials with freeform surfaces

    by Burak Ozdemir, Erol Kilickap, Erkan Bahce, Ahmet Yardimeden, Ender Emir

    In the drilling process, the angle of surface is one of the parameters that affect hole quality. In study, the effects of feed rate, spindle speed and surface angle on the thrust force, roughness, and delamination, which are the factors affecting the quality of hole, were investigated in the drilling of GFRP (glass fiber reinforced polymer) and CFRP (carbon fiber reinforced polymer) with freeform surfaces. With ANOVA (Analysis of Variance) and regression analysis, the parameter effects were statistically compared, and descriptive mathematical models were derived. The mathematical models were subjected to the Genetic Algorithm approach according to the different surface angles determined and the optimum parameter values were calculated. Guiding data were obtained about the effects of machining on hole quality in drilling composite at different surface angles, which is the main motivation of the study. Optimization results will improve hole quality on curved surfaces, while saving cost and time. Graphical Abstract