Matheus Rover Barbieri
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Matheus Rover Barbieri has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Lydia Achelis
Univ Bremen, Fac Prod Engn, Particles & Proc Engn Dept, Badgasteiner Str 3, D-28359 Bremen, Germany
2 shared publications- Udo Fritsching
Leibniz Institute for Materials Engineering-IWT, Badgasteiner Str. 3, 28359 Bremen, Germany
2 shared publications Dilamara R. Scharf
1 shared publicationG. Ebner
Leibniz Institute for Materials Engineering – IWT , Badgasteiner Str. 3 , Bremen Germany
1 shared publicationHenry França Meier
1 shared publicationJeferson Colzani
1 shared publication
Latest Publications
- Open Access
Characterizing the Internal Flow Behavior of Spray Pulsating Operation in Internal-Mixing Y-Jet Atomizers
The production of a stable and uniform spray is a primary concern in fuel atomization applications, such as in fluid catalytic cracking reactors, directly affecting the process quality and gas emissions. However, depending on nozzle geometry and operating conditions, undesired pulsed spray behavior may occur. This phenomenon originates from the internal multiphase flow interaction in Y-jet nozzles and leads to unstable sprays. Understanding the formation of spray pulsations is challenging due to limited internal flow visualization in the nozzle and the fast dynamics involved. Accordingly, this work elucidates the mechanisms of the pulsed spray formation through 3D transient numerical multiphase simulations inside a mixing chamber. The model is validated against internal pressure measurements and applied to investigate the internal mixing behavior across several operating conditions. Results show that the liquid-to-gas momentum flux ratio governs the internal flow regimes. A higher liquid momentum flux obstructs the gas flow, leading to periodic spray bursts when the gas overcomes the liquid back pressure. The simulations also reveal self-sustained oscillatory flow patterns and cyclic transitions between gas penetration and liquid accumulation, which produce periodic pressure fluctuations and nozzle discharge pulsations. The findings offer valuable guidance for optimizing nozzle operation and geometry to suppress pulsation and improve atomization performance.
Open AccessCharacterizing the Internal Flow Behavior of Spray Pulsating Operation in Internal-Mixing Y-Jet Atomizers
The production of a stable and uniform spray is a primary concern in fuel atomization applications, such as in fluid catalytic cracking reactors, directly affecting the process quality and gas emissions. However, depending on nozzle geometry and operating conditions, undesired pulsed spray behavior may occur. This phenomenon originates from the internal multiphase flow interaction in Y-jet nozzles and leads to unstable sprays. Understanding the formation of spray pulsations is challenging due to limited internal flow visualization in the nozzle and the fast dynamics involved. Accordingly, this work elucidates the mechanisms of the pulsed spray formation through 3D transient numerical multiphase simulations inside a mixing chamber. The model is validated against internal pressure measurements and applied to investigate the internal mixing behavior across several operating conditions. Results show that the liquid-to-gas momentum flux ratio governs the internal flow regimes. A higher liquid momentum flux obstructs the gas flow, leading to periodic spray bursts when the gas overcomes the liquid back pressure. The simulations also reveal self-sustained oscillatory flow patterns and cyclic transitions between gas penetration and liquid accumulation, which produce periodic pressure fluctuations and nozzle discharge pulsations. The findings offer valuable guidance for optimizing nozzle operation and geometry to suppress pulsation and improve atomization performance.
- 16 September 2025
- Published by Elsevier in Ocean Engineering
- Vol. 341
Cylinder excitation response in flow-induced vibration of large tube arrays for offshore applications
- 16 September 2025
- Published by Elsevier in Ocean Engineering
- Vol. 341
Cylinder excitation response in flow-induced vibration of large tube arrays for offshore applications
- Open Access
- 12 October 2024
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 181
Spray characteristics of steam-assisted oil atomization in Y-jet nozzles
- 12 October 2024
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 181
Open AccessSpray characteristics of steam-assisted oil atomization in Y-jet nozzles
- 1 October 2024
- Published by Walter de Gruyter GmbH in HTM Journal of Heat Treatment and Materials
- Vol. 79 (5) , 245-265
Flow Field Analysis within Industrial Quenching Tanks Operated with Aqueous Polymer Solutions in the Steel Industry
Quenching with polymer solutions for steel heat treatment offers adjustable performance and improved ecological impact compared to conventional water or oil quenching. The submersion cooling operation poses challenges due to the intense vapor/polymer film collapse on the component surface, potentially destabilizing batch components. Therefore, controlled recirculation is critical to preventing tank and specimen damage during cooling and ensuring effective steel hardening. However, flow structure analysis is often overlooked and disregarded in industrial tank design. Thus, this study evaluates the tank geometries of two partner industries to determine if they provide the necessary homogeneous flow for optimal quenching. The analysis combines experimental velocity measurements with a numerical model, with the identification of different flow intensity regions being the main outcome of this work. The results suggest that geometric modifications could improve flow recirculation, enhancing quenching performance.
- 1 October 2024
- Published by Walter de Gruyter GmbH in HTM Journal of Heat Treatment and Materials
- Vol. 79 (5) , 245-265
Flow Field Analysis within Industrial Quenching Tanks Operated with Aqueous Polymer Solutions in the Steel Industry
Quenching with polymer solutions for steel heat treatment offers adjustable performance and improved ecological impact compared to conventional water or oil quenching. The submersion cooling operation poses challenges due to the intense vapor/polymer film collapse on the component surface, potentially destabilizing batch components. Therefore, controlled recirculation is critical to preventing tank and specimen damage during cooling and ensuring effective steel hardening. However, flow structure analysis is often overlooked and disregarded in industrial tank design. Thus, this study evaluates the tank geometries of two partner industries to determine if they provide the necessary homogeneous flow for optimal quenching. The analysis combines experimental velocity measurements with a numerical model, with the identification of different flow intensity regions being the main outcome of this work. The results suggest that geometric modifications could improve flow recirculation, enhancing quenching performance.
- 5 August 2023
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 168
Effect of Y-jet nozzle geometry and operating conditions on spray characteristics and atomizer efficiency
- 5 August 2023
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 168
Effect of Y-jet nozzle geometry and operating conditions on spray characteristics and atomizer efficiency