EJEduardo Affonso Jung

Eduardo Affonso Jung

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Eduardo Affonso Jung has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Electronic rod profilometer for soil mobilization measurement

    by Gabriel G. Zimmermann, Eduardo A. Jung, William S. De Mendonça, Tiago R. Francetto, Eduardo A. Gracietti, Samir P. Jasper

    Aim of the study: This study aimed to develop and validate an electronically enhanced rod profilometer capable of operating independently under field conditions and to compare laser, LiDAR, and ultrasonic sensors to identify the technology least affected by environmental interference during soil surface roughness measurements. Area of study: Federal University of Parana, Curitiba, Brazil. Material and methods: A laboratory experiment was carried out using a completely randomized design, comparing a conventional rod profilometer with electronic profilometers equipped with laser, LiDAR, and ultrasonic sensors. Modified roughness, elevated area, mobilized area, blistering, and soil thickness were evaluated, with seven replicates per treatment. Data were tested for normality and homogeneity and subsequently subjected to analysis of variance. When significant differences were detected, means were compared using the Student–Newman–Keuls (SNK) test at a 5% significance level. Main results: The electronically enhanced rod profilometer demonstrated satisfactory accuracy, precision, and reliability when compared to the conventional method, confirming the validation of the equipment. Among the evaluated sensors, the ultrasonic sensor exhibited the most consistent and reliable performance for stem readings due to its wider beam angle, which increased detection probability and reduced susceptibility to environmental interferences such as solar incidence and soil reflectance. Research highlights: Sensor selection critically affects measurement reliability in electronically enhanced rod profilometry under field conditions.

  • Open Access

    Radial and bias-ply tires used in sugarcane transshipment deflection and soil pressure at two depths under controlled conditions

    by Eduardo Affonso Jung, William Santiago de Mendonça, Eduardo Alves Gracietti, Gabriel Ganancini Zimmermann, Jayne Raquel de Oliveira, Karina Maria Vieira Cavalieri-Polizeli, Aldir Carpes Marques Filho, Tiago Rodrigo Francetto, Samir Paulo Jasper

    Soil compaction caused by heavy machinery traffic is one of the main physical constraints to crop production, especially in sugarcane systems where tire type and load intensity strongly affect soil structure. Understanding how tire construction modifies deflection behavior and stress transmission is essential to support more sustainable mechanization practices. This study evaluated the performance of radial and bias-ply agricultural tires used in sugarcane transshipments, focusing on their deflection patterns and stresses applied to the soil. Tests were carried out with a hydraulic press applying progressive loads up to 6100 kgf on both tire types, calibrated at 45 psi (310 kPa). Vertical and horizontal deflections were measured with displacement sensors, while soil stresses were monitored with load cells installed at depths of 0.10 and 0.20 m. Data were analyzed using analysis of covariance (ANCOVA), considering load as a covariate and tire type as a fixed factor. Results showed that radial tires presented greater sensitivity in vertical deflection but lower lateral deformation, while bias-ply tires displayed higher lateral deflection and concentrated stresses at the soil surface. At 0.20 m, pressures were attenuated, but the interaction between load and tire type revealed that radials dissipated stress more gradually. These findings demonstrated that tire construction directly influences the magnitude and distribution of soil stress. The adoption of radial tires in sugarcane production systems can mitigate soil compaction and contribute to the sustainability of mechanized agriculture.

  • Open Access

    Operational performance of an agricultural tractor with different tire technologies on two surfaces

    by Gabriel Ganancini Zimmermann, Samir Paulo Jasper, Eduardo Affonso Jung, Eduardo Alves Gracietti, Anderson Muniz Calhabeu, Fábio Volkmer Soares

    Standard, IF, and VF radial tire technologies have brought significant advancements in load capacity and the operational efficiency of modern agricultural tractors. These improvements have contributed to reduced fuel consumption and greater sustainability in agricultural operations. However, limited research exists on the performance of agricultural tractors equipped with different tire technologies under real field conditions. Therefore, this study evaluated the operational performance of an agricultural tractor fitted with standard, IF, and VF radial tires on both concrete and firm soil surfaces. The experiment followed a strip-plot randomized block design with three tire technologies (standard, IF, and VF) as main plots and two surfaces (concrete and soil) as subplots, with five replicates, totaling 30 experimental units. Parameters monitored included engine speed, wheel slip, operating speed, drawbar pull, drawbar power and efficiency, hourly and specific fuel consumption, and engine thermal efficiency. Results showed that the concrete surface enabled higher speeds and lower fuel consumption, while the firm soil required greater engine speed and exhibited higher slip. VF tires outperformed standard tires in energy efficiency, traction, and contact area, offering higher speeds and reduced slip. However, under firm soil conditions, VF tires required additional ballast to reach optimal performance. IF tires demonstrated intermediate performance.

  • Open Access

    Operational and energy performance of a powershift transmission tractor during tillage at different speeds

    by Eduardo A. Jung, Gabriel G. Zimmermann, William S. de Mendonça, Samir P. Jasper, Eduardo A. Gracietti

    Agricultural machinery plays a key role in optimizing crop yields. In tillage operations, it is essential to analyze both operational and energy performance variables. Continuous research is needed to quantify performance without compromising soil conservation, particularly with modern agricultural tractors, to update strategies, increase productivity and ensure the sustainability of mechanized operations. This study aimed to assess the energy and operational efficiency of an agricultural tractor (John Deere®, model 8400R), during subsoiling at different speeds, using five gear settings (A, B, C, D and E, corresponding to gears F5, F6, F7, F8 and F9), with a nominal engine speed of 2,100 rpm. The parameters evaluated were operating speed, wheel slip, engine speed, drawbar force, drawbar efficiency, hourly fuel consumption, fuel consumption per unit area, brake specific fuel consumption, brake thermal efficiency, and field capacity. The experiment followed a randomized block design. Analysis of variance indicated significant improvements in operating speed, wheel slippage, engine speed, drawbar force and drawbar efficiency as the gears shifted from A to E. Correlation analysis showed strong relationships between operating speed and parameters such as wheel slippage, drawback force and drawback efficiency, hourly fuel consumption and operational field capacity. Gear D was the most efficient for tillage. Although gear E improved operational performance, it reduced energy efficiency, indicating a trade-off between speed and fuel economy.


  • Open Access

    Energy efficiency of four-wheel drive tractor in sowing operation

    by Samir Paulo Jasper, William Santiago de Mendonça, Eduardo Affonso Jung, Gabriel Ganancini Zimmermann, Eduardo Alves Gracietti

    The breakthrough of articulated tractors has led to a significant increase in productivity and a cost reduction of agricultural operations. The performance of the tractor implement system depends on the understanding of the tractors’ energy parameters. Fertilizer seeders operate between 6 and 9 km h-1, while seed drills allow higher speeds. Increasing sowing speed improves operational efficiency. However, it is important to adequately set the machinery, to optimize the energy parameters, considering the balance between productivity and sustainability. This study evaluated the energy and operating parameters of a 398kW articulated agricultural tractor in a sowing operation at different speeds. The experiment was conducted in a complete randomized block design. Five theoretical speeds were chosen for the sowing operation (6, 7, 8, 9 and 10 km h-1), with seven replications (35 units). The tractor operating parameters were measured: operational speed, slippage, engine speed, hourly fuel consumption, engine thermal efficiency, specific fuel consumption, drawbar force, drawbar efficiency, fuel consumption per area and field operating capacity. The data were subjected to normality test, when significant, variance analysis. Results showed high field capacity in the highest speed and low fuel consumption per area at the highest speed.


  • Open Access

    Impact of on-farm and industrial treatments on seed longitudinal distribution for soybeans

    by Eduardo A. Gracietti, Samir P. Jasper, Gabriel G. Zimmermann, William S. de Mendonça, Eduardo A. Jung

    Adequate seed placement is essential for consistent crop emergence and initial growth. Pneumatic seed metering systems offer superior longitudinal seed distribution accuracy compared to traditional methods, yet certain factors can influence this precision. For instance, seed physical properties may be altered by phytosanitary treatments applied either on-farm or industrially. This study examined the effects of phytosanitary treatment type and graphite addition on soybean seed deposition using an electric-driven pneumatic feeder under simulated sowing conditions. Seed distribution was monitored with an optical sensor. Four treatment groups were established: untreated without graphite, untreated with graphite added, on-farm treated with graphite, and industrially treated with graphite. Parameters assessed included average spacing between seeds, coefficient of variation, precision index, multiple and failed spacings, and percentage of acceptable spacing. Results indicate that prior seed treatment does not significantly affect overall planting accuracy. However, seed spacing varied between the untreated and on-farm treated groups, with the latter demonstrating closer proximity to optimal values. Both on-farm and industrial treatments yielded more uniform seed deposition, as indicated by a lower coefficient of variation. Regardless of seed treatment, the pneumatic feeder consistently performed effectively.

  • Open Access

    Bioactive compounds in gladiolus flowers

    by Alexandra Goede de Souza, Eduardo Affonso Jung, Vinícius Petermann Benedicto, Leosane Cristina Bosco

    Flowers have received special attention not only for their ornamental nature but also for their nutraceutical, cosmetic, aromatic, and culinary properties. This study aimed to characterize physicochemical attributes and the antioxidant capacity of flowers of four gladiolus cultivars. The cultivars used were White Friendship, Rose Supreme, Jester, and T704. We analyzed the content of total soluble solids (SS), total titratable acidity (TA), SS/TA ratio, pH, vitamin C, anthocyanin, flavonoids, total phenolic compounds (TPC), total antioxidant activity (TAA), and the relationship of TPC with flavonoids and TAA for each cultivar. The results showed that the Jester flowers had the lowest TA and highest SS/TA ratio, indicating the best flavor. Jester also had the highest flavonoid content, similarly to the White Friendship and Rose Supreme. As a result, these cultivars have flowers with higher TPC and TAA content than T704. The anthocyanin content was the characteristic attribute of cultivar T704, due to its purple pigmentation. Gladiolus flowers, traditionally used in landscaping and as cut flowers, have the potential for use in human nutrition, particularly the White Friendship, Rose Supreme, and Jester cultivars.


  • Open Access

    Efeito do sistema de cultivo na produção de gladíolos no Alto Vale do Itajaí, SC

    by Alexandra Goede De Souza, Fernada Gonçalves Broggiatto, David Pires de Azeredo Neto, Leosane Cristina Bosco, Eduardo Affonso Jung

    O objetivo deste trabalho foi avaliar o efeito do sistema de cultivo no desenvolvimento das plantas e na qualidade das hastes florais de gladíolos. O delineamento experimental utilizado foi inteiramente casualizado com dois cultivares: White Goddess e Red Beauty; duas datas de colheita: Dias das Mães (DM) e Dia dos namorados (DN); e dois sistemas de cultivo: convencional e mínimo. Nas plantas foram avaliadas o número de folhas, massa seca total, número de floretes, dias para emergência e ponto de colheita, comprimento e diâmetro da haste. Para Red Beauty cultivada para o DM, o cultivo mínimo proporcionou maior número de folhas, comprimento e diâmetro da haste; e para o DN, aumento da massa seca, do número de floretes e dias para emergência. Para White Goddess houve efeito do sistema de cultivo somente no DM, quando as plantas apresentaram, no cultivo mínimo, maior diâmetro e comprimento da haste e menor da massa seca. Para Red Beauty, 83,4% e 25% das hastes foram classificadas como extra no cultivo mínimo e convencional, respectivamente, enquanto a White Goddess apresentou 100% das hastes como extra em ambos os sistemas de cultivo.