Jian Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jian Zhang has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Chuanmao Lv
College of Mechanical & Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
2 shared publications Hong Zhang
College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing, China
2 shared publications- Chengcheng Ji
College of Mechanical & Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
1 shared publication ChuanMao Lv
College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing, China
1 shared publicationHaoRan Lu
College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing, China
1 shared publicationHou Xiangying
National Key Laboratory of Science and Technology on Helicopter Transmission, Nanjing University of Aeronautics and Astronautics, Nanjing, China
1 shared publication
Latest Publications
- Open Access
Research on Quasi-Static Transmission Error Measurement of Spur Gears Based on the Acceleration Method
Transmission error (TE) is an important parameter in gear dynamics that has a direct impact on the vibration and noise of gears. Under quasi-static conditions, gear elastic deformation and assembly errors amplify with increasing load, potentially contributing to noise and vibration. This paper presents a novel method for measuring the quasi-static transmission error (QSTE) of spur gears under quasi-static conditions. In particular, the study investigates the relationship between quasi-static transmission error, elastic deformation transmission error, and gear tangential acceleration. Gear elastic deformation transmission error was calculated from experimental data obtained with single-point, symmetrical dual-point, and orthogonal four-point configurations of tangential acceleration sensors. The orthogonal four-point sensor configuration greatly improves measurement accuracy when compared to theoretical values derived from material mechanics calculations. A dedicated on-machine acquisition system for spur gear tangential acceleration was constructed. Tangential acceleration tests were conducted across varying loads and rotational speeds. The acquired data underwent filtering and integration processing in order to obtain gear elastic deformation and quasi-static transmission error. The feasibility of the acceleration approach for measuring both gear elastic deformation and quasi-static transmission error is confirmed by a comparative analysis of the acceleration method results with transmission errors obtained via material mechanics calculations and magnetic grating detection.
Open AccessResearch on Quasi-Static Transmission Error Measurement of Spur Gears Based on the Acceleration Method
Transmission error (TE) is an important parameter in gear dynamics that has a direct impact on the vibration and noise of gears. Under quasi-static conditions, gear elastic deformation and assembly errors amplify with increasing load, potentially contributing to noise and vibration. This paper presents a novel method for measuring the quasi-static transmission error (QSTE) of spur gears under quasi-static conditions. In particular, the study investigates the relationship between quasi-static transmission error, elastic deformation transmission error, and gear tangential acceleration. Gear elastic deformation transmission error was calculated from experimental data obtained with single-point, symmetrical dual-point, and orthogonal four-point configurations of tangential acceleration sensors. The orthogonal four-point sensor configuration greatly improves measurement accuracy when compared to theoretical values derived from material mechanics calculations. A dedicated on-machine acquisition system for spur gear tangential acceleration was constructed. Tangential acceleration tests were conducted across varying loads and rotational speeds. The acquired data underwent filtering and integration processing in order to obtain gear elastic deformation and quasi-static transmission error. The feasibility of the acceleration approach for measuring both gear elastic deformation and quasi-static transmission error is confirmed by a comparative analysis of the acceleration method results with transmission errors obtained via material mechanics calculations and magnetic grating detection.
- Open Access
Investigation of High-Speed Dynamic Transmission Error Testing Using Gear Strain
The difficulties of testing the dynamic transmission errors of gears in complex environments, such as high-speed operations or situations with oil contamination, and the limited variety of available testing methods have been recognized as issues which this study endeavors to tackle. In this study, a testing method for evaluating high-speed dynamic transmission errors of spur gears through the use of strain sensors is proposed. To reduce the interference of environmental noise on testing signals, physical measures, such as the use of copper foil to shield signal wires and the grounding of data acquisition equipment, were implemented during the testing process. Utilizing wavelet decomposition to distinguish between the high- and low-frequency components of the testing signals, the transmission error of gears during high-speed operation was calculated. After confirming the feasibility of the stress–strain stiffness approach in gear transmission error testing using the magnetic grid method, tests on modified and non-modified gears at various speeds and loads were carried out. The two types of test data were processed and evaluated to determine the effect of speed and load on gear dynamic transmission error. It was possible to conduct research on the testing technique of gear dynamic transmission errors utilizing strain sensors, which provides a new, fast, simple, and practical testing strategy for gear transmission error testing.
Open AccessInvestigation of High-Speed Dynamic Transmission Error Testing Using Gear Strain
The difficulties of testing the dynamic transmission errors of gears in complex environments, such as high-speed operations or situations with oil contamination, and the limited variety of available testing methods have been recognized as issues which this study endeavors to tackle. In this study, a testing method for evaluating high-speed dynamic transmission errors of spur gears through the use of strain sensors is proposed. To reduce the interference of environmental noise on testing signals, physical measures, such as the use of copper foil to shield signal wires and the grounding of data acquisition equipment, were implemented during the testing process. Utilizing wavelet decomposition to distinguish between the high- and low-frequency components of the testing signals, the transmission error of gears during high-speed operation was calculated. After confirming the feasibility of the stress–strain stiffness approach in gear transmission error testing using the magnetic grid method, tests on modified and non-modified gears at various speeds and loads were carried out. The two types of test data were processed and evaluated to determine the effect of speed and load on gear dynamic transmission error. It was possible to conduct research on the testing technique of gear dynamic transmission errors utilizing strain sensors, which provides a new, fast, simple, and practical testing strategy for gear transmission error testing.
- 27 June 2023
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Mechanical Engineering
- Vol. 48 (2) , 723-731
Quasi-Static Transmission Error Measurement Using Micro-Deformation
- 27 June 2023
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Mechanical Engineering
- Vol. 48 (2) , 723-731
Quasi-Static Transmission Error Measurement Using Micro-Deformation
- Open Access
- 16 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 167736-167743
Sensorless Speed and Position Identification of Rim Electromagnetic Direct-Driven Propeller Based on Sliding-Mode Observer
Rim electromagnetic direct-driven propeller (REDP) is a propeller used in the underwater vehicle. It has many merits compared with the traditional propeller. It is difficult to utilize the sensor to get the rotor position and speed that are important to control REDP. An observer based on sliding mode method was proposed to estimate the rotor position and speed in the paper. Its stability was proved and some parameters were obtained. The influence of the switching function on the observation performance was analyzed and the sigmoid function was chosen as the switching function of the sliding mode observer. Then the observation position and speed were analyzed under different parameters to get the better observation performance. Finally, the experiment verified the feasibility of sliding mode observer.
- 16 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 167736-167743
Open AccessSensorless Speed and Position Identification of Rim Electromagnetic Direct-Driven Propeller Based on Sliding-Mode Observer
Rim electromagnetic direct-driven propeller (REDP) is a propeller used in the underwater vehicle. It has many merits compared with the traditional propeller. It is difficult to utilize the sensor to get the rotor position and speed that are important to control REDP. An observer based on sliding mode method was proposed to estimate the rotor position and speed in the paper. Its stability was proved and some parameters were obtained. The influence of the switching function on the observation performance was analyzed and the sigmoid function was chosen as the switching function of the sliding mode observer. Then the observation position and speed were analyzed under different parameters to get the better observation performance. Finally, the experiment verified the feasibility of sliding mode observer.
- Open Access
- 6 August 2021
- Published by Springer Nature in Research Square
Design And Power Generation Performance Analysis of A Rim-Driven Wave Energy Generator
Wave energy exploitation is getting more attention from researchers Many types of devices that can convert wave energy into electricity have been designed. At present, engineers and scientists are researching how to make a simple and efficient wave energy capture device. This paper explored the rim-driven generator. In a rim-driven wave energy generator, the rotor blade could harvest kinetic energy of wave motions. The blade is inside of the generator and the gap between the stator and the rotor is water-filled. This structure could improve the compactness and reliability of the wave energy generator. The paper studied the influence of the arrangement of the blade and the structure of the generator on the performance of the generator. Analytical models were designed to obtain generator’s performance. The result could optimize the design of generator and improve the energy conversion efficiency.
- 6 August 2021
- Published by Springer Nature in Research Square
Open AccessDesign And Power Generation Performance Analysis of A Rim-Driven Wave Energy Generator
Wave energy exploitation is getting more attention from researchers Many types of devices that can convert wave energy into electricity have been designed. At present, engineers and scientists are researching how to make a simple and efficient wave energy capture device. This paper explored the rim-driven generator. In a rim-driven wave energy generator, the rotor blade could harvest kinetic energy of wave motions. The blade is inside of the generator and the gap between the stator and the rotor is water-filled. This structure could improve the compactness and reliability of the wave energy generator. The paper studied the influence of the arrangement of the blade and the structure of the generator on the performance of the generator. Analytical models were designed to obtain generator’s performance. The result could optimize the design of generator and improve the energy conversion efficiency.
- 1 June 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 236 (2) , 752-762
Electromagnetic performance analysis of the rim electromagnetic direct-driven propeller
Propellers are a crucial part to drive underwater vehicles. A rim electromagnetic direct-driven propeller (REDP) had been presented to meet some specific requirements of the underwater vehicle in this paper. It had many advantages compared to classical propellers and could improve the performance of the underwater vehicle. The composition and working mode of REDP were introduced here. In addition, the paper also introduced the working characteristics of REDP and somethings needed to be improved. The energy method was utilized to calculate the distribution of magnetic fields. A three-dimensional model of REDP was built. Then the influence of the propeller’s parameters on performance was analyzed, including the number, pattern, surface radian of the permanent magnet and the stator cogging skew, by finite element computing models. The performances of REDP were tested under several parameters. Some valuable conclusions were obtained according the test results and could provide a reference for the design and performance optimization of REDP utilized on the underwater vehicle.
- 1 June 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 236 (2) , 752-762
Electromagnetic performance analysis of the rim electromagnetic direct-driven propeller
Propellers are a crucial part to drive underwater vehicles. A rim electromagnetic direct-driven propeller (REDP) had been presented to meet some specific requirements of the underwater vehicle in this paper. It had many advantages compared to classical propellers and could improve the performance of the underwater vehicle. The composition and working mode of REDP were introduced here. In addition, the paper also introduced the working characteristics of REDP and somethings needed to be improved. The energy method was utilized to calculate the distribution of magnetic fields. A three-dimensional model of REDP was built. Then the influence of the propeller’s parameters on performance was analyzed, including the number, pattern, surface radian of the permanent magnet and the stator cogging skew, by finite element computing models. The performances of REDP were tested under several parameters. Some valuable conclusions were obtained according the test results and could provide a reference for the design and performance optimization of REDP utilized on the underwater vehicle.
- Open Access
- 6 May 2020
- Published by EDP Sciences in Mechanics & Industry
- Vol. 21 (4) , 406
Rotational speed control of magnetic coupling with variable damping method
Permanent Magnetic Coupling (PMC) is used in underwater vehicle to transmit torque from the motor to propeller without leakage and friction. Output rotational speed stability of PMC is an important index indicating the PMC output makes smaller vibration. To improve the stability of the output rotational speed, PMC dynamic characteristic was analyzed based on Lagrange equation in this paper. The dynamic characteristic was indicated by the angular phase generated by the master rotor and the slave rotor. The angular phase varied with the damping coefficient, torsional rigidity and rotational inertia of PMC. These parameters' influence on the angular phase was analyzed and the results revealed the rules between these parameters and the angular phase. Based on the rules, a variable damping method was proposed to control the angular phase. The angular phase changed smoothly with this method that was used to design a variable damping controller based on electromagnetic damping effect principle. This method was verified by theoretical calculation and finite element analysis (FEA). Finally, a novel variable damping PMC was designed to improve the output rotational speed stability of PMC.
- 6 May 2020
- Published by EDP Sciences in Mechanics & Industry
- Vol. 21 (4) , 406
Open AccessRotational speed control of magnetic coupling with variable damping method
Permanent Magnetic Coupling (PMC) is used in underwater vehicle to transmit torque from the motor to propeller without leakage and friction. Output rotational speed stability of PMC is an important index indicating the PMC output makes smaller vibration. To improve the stability of the output rotational speed, PMC dynamic characteristic was analyzed based on Lagrange equation in this paper. The dynamic characteristic was indicated by the angular phase generated by the master rotor and the slave rotor. The angular phase varied with the damping coefficient, torsional rigidity and rotational inertia of PMC. These parameters' influence on the angular phase was analyzed and the results revealed the rules between these parameters and the angular phase. Based on the rules, a variable damping method was proposed to control the angular phase. The angular phase changed smoothly with this method that was used to design a variable damping controller based on electromagnetic damping effect principle. This method was verified by theoretical calculation and finite element analysis (FEA). Finally, a novel variable damping PMC was designed to improve the output rotational speed stability of PMC.