ABAlina Boiangiu

Alina Boiangiu

*This is an algorithmically generated author record based on publicly available information.

Alina Boiangiu has a total of 30 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Research Progress in Lanthanum Extraction from Boehmite

    by Ana-Cristiane Dragomir, Nicoleta Sorina Nemeş, Ionuţ Bălescu, Mihaela Ciopec, Adina Negrea, Narcis Duteanu, Cătălin Ianăşi, Orsina Verdes, Mariana Suba, Paula Svera, et al.

    The purpose of this study was to examine the utilization of 0–45 μm aluminum hydrate fraction (gibbsite) manufactured by Alum SA Tulcea, as a precursor in the hydrothermal synthesis process of nanosize boehmite from gibbsite suspensions. Furthermore, the use of the produced material as adsorbent of lanthanum (III) ions was investigated using aqueous solutions. Thermogravimetric analysis (TG), Fourier Transform InfraRed Spectroscopy (FT-IR), Wide-Angle X-Ray Scattering (WAXS), and atomic force microscopy (AFM) were used to demonstrate the preparation of the required material. Additionally, the material point of zero charge (pHpzc) and material specific surface (using BET approach) were evaluated. By conducting adsorption studies, the specific parameters for the lanthanum adsorption process were evaluated. The effects of pH, the ratio of adsorbent material to La(III) quantity from aqueous solution, contact time, and La(III) initial concentration were also assessed. Based on the obtained experimental data, it was proved that the maximum adsorption capacity of 97.7 mg/g was obtained for a solid:liquid ratio = 0.1 g:25 mL, pH between 3 and 6, temperature of 298 K, and contact time of 90 min. The studied adsorption process is most effectively described by the Sips model, suggesting an intricate interaction among the adsorbent material and La (III) ions. The prepared adsorbent exhibited a good desorption capacity (higher than 93%) when 20% HCl was used for desorption.


  • Open Access

    Preliminary Characterization of Three Metallurgical Bauxite Residue Samples

    by Panagiotis Angelopoulos, Maria Georgiou, Paschalis Oustadakis, Maria Taxiarchou, Hakan Karadağ, Yasin Eker, Gheorghe Dobra, Alina Boiangiu, Gökhan Demir, Sedat Arslan, et al.

    Bauxite Metallurgical Residue (BR) is a highly alkaline and very fine-grained by-product of the Bayer process for alumina production. Its huge global annual production has resulted in increasing accumulation of BR, causing deposition problems and serious environmental issues. RM contains oxides and salts of the main elements Fe, Al, Ca, Na, Si, Ti, and rare earths—REEs (Sc, Nd, Y, La, Ce, Ds)—many of which have been categorised by EU as critical metals (CMs). The valorisation of BR as a low-cost secondary raw material and metal resource could be a route for its reduction, introducing the waste into the economic cycle. REEScue constitutes a research project that aims to instigate the efficient exploitation of European bauxite residues, resulting from alumina production from Greece (MYTILINEOS SA), Turkey (ETI Aluminium), and Romania (ALUM SA), containing appreciable concentrations of scandium and REEs, through the development of a number of innovative extraction and separation technologies that can efficiently address the drawbacks of the existing solution. The consortium consists of three alumina producers from Greece (MYTILINEOS SA), Turkey (ETI Aluminium), and Romania (ALUM SA) and two academic partners from Greece (National Technical University of Athens) and Turkey (Necmettin Erbacan University). We present preliminary characterization results of three different BR samples that originate from the three aluminium industries, in respect of bulk chemical analysis (XRF, ICP), mineralogical investigation (XRD), and morphological observation through microscopy.


  • Open Access

    Thermally Activated Al(OH)3 Part II—Effect of Different Thermal Treatments

    by Bogdan Stefan Vasile, Gheorghe Dobra, Sorin Iliev, Lucian Cotet, Ionela Andreea Neacsu, Vasile Adrian Surdu, Adrian Ionut Nicoara, Alina Boiangiu, Laurențiu Filipescu

    In this paper, the thermal decomposition of crystalline Al(OH)3 was studied over the temperature range of 260–400 °C for particles with a size between 10 and 150 µm. The weight losses and thermal effects occurring in each of the dehydration process were assessed using thermogravimetry (TG) and differential scanning calorimetry (DSC) thermal analysis. X-ray diffraction (XRD) patterns, refined by the Rietveld method, were used for mineral phase identification, phase composition analysis, and crystallinity degree determination. Moreover, the particle size distributions and their corresponding D10, D50, and D90 numeric values were determined with a laser analyzer. We observed a strong relationship between the calcination temperature, the initial gibbsite grade particle size, and the crystallinity of the resulting powders. Hence, for all endothermic effects identified by DSC, the associated temperature values significantly decreased insofar as the particle dimensions decreased. When the gibbsite was calcined at a low temperature, we identified small amounts of boehmite phase along with amorphous new phases and unconverted gibbsite, while the powders calcined at 400 °C gradually yielded a mixture of boehmite and crystalized γ-Al2O3. The crystallinity % of all phase transition products declined with the increase in particle size or temperature for all the samples.


  • Open Access

    Thermally Activated Al(OH)3: Part I—Morphology and Porosity Evaluation

    by Bogdan Stefan Vasile, Gheorghe Dobra, Sorin Iliev, Lucian Cotet, Ionela Andreea Neacsu, Adrian Ionut Nicoara, Vasile Adrian Surdu, Alina Boiangiu, Laurențiu Filipescu

    Aluminum hydroxide is an essential material for the industrial production of ceramics (especially insulators and refractories), desiccants, absorbents, flame retardants, filers for plastics and rubbers, catalysts, and various construction materials. The calcination process of Al(OH)3 first induces dehydration and, finally, results in α-Al2O3 formation. Nevertheless, this process contains various intermediary steps and has been proven to be complicated due to the development of numerous transitional alumina. Each step of the investigation is vital for the entire process because the final properties of materials based on aluminum trihydroxide are determined by their phase composition, morphology, porosity, etc. In this paper, five dried, milled, and size-classified aluminum hydroxide specimens were thermally treated at 260, 300, and 400 °C; then, they were studied in order to identify the effects of temperature on their properties, such as particle morphology, specific surface area, pore size, and pore distribution. The major oxide compounds identified in all samples were characteristic of bauxite—namely, Al2O3 * 3H2O, SiO2, Fe2O3, Na2O, and CaO. Particles with smaller sizes (2/g and their small pore width (3–3.5 nm).