Fareed Hameed Majeed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Fareed Hameed Majeed has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Abdullah Al-Hussein
Department of Civil Engineering, College of Engineering, University of Basrah, Basrah 61004, Iraq
3 shared publications - Abdulamir Atalla Karim
Department of Civil Engineering, College of Engineering, University of Basrah, Basra 61004, Iraq
2 shared publications Samoel Mahdi Saleh
Department of Civil Engineering College of Engineering Basrah University Basra Iraq
2 shared publications- Samoel Mahdi Saleh
College of Engineering, University of Basrah, Basrah 61004
2 shared publications Abdullah Al-Hussein
1 shared publication- Abdulnasser M. Abbas
Department of Civil Engineering, University of Basrah, Basra 61004, Iraq
1 shared publication
Latest Publications
- Open Access
Damage Monitoring in Recycled Aggregate Concrete Reinforced with Hybrid Steel–Polyolefin Fibers Using Acoustic Emission Technique
The mechanical properties and real-time damage evolution of sustainable concrete (SC) containing 100% recycled concrete aggregate (RCA) under the combined action of hybrid steel and polyolefin fibers were studied. Inspired by solving the massive effects on the environment from construction waste, as well as to improve the lower mechanical performance of lower-grade RCA, the effect of combining high-stiffness hooked-end steel fibers and flexible macro-polyolefin fibers within RCA was investigated. Six different mix designs were considered: plain, single-fiber (100% steel and 100% polyolefin) and three hybrid composites with varying fractions of the steel/polyolefin fibers (25/75, 50/50, and 75/25). Compressive, tensile and flexural strengths were determined by mechanical testing. During compressive testing, the damage evolution was monitored using low-cost acoustic emission (AE) as a non-destructive technique. Cumulative hits analysis, amplitude distributions, and the statistical b-value parameter were used for damage characterization. The results show that steel fiber significantly increased compressive strength (an increase of up to 13.8%), and the 50/50 hybrid mix showed a high synergistic effect, yielding the highest tensile (4.86 MPa) and flexural (25.54 MPa) strengths. AE analysis identified different damage fingerprints: Based on amplitude analysis, steel-fiber composites exhibited high-amplitude events (which may be attributable to fiber pull-out); polyolefin-fiber composites generated medium-amplitude events (may have resulted from distributed microcracking); and hybrid mixes displayed a mixed amplitude distribution. The b-value analysis provided insight into progressive damage and revealed that the hybrid fibers induce stable, diffuse damage that prevents the brittle failure of plain recycled aggregate concrete (RAC). The results show that hybrid fiber reinforcement can be a reliable approach to enhance the mechanical performance and crack resistance of RAC. Furthermore, low-cost acoustic emission (AE) serves as an effective non-destructive method for monitoring damage progression within the material.
Open AccessDamage Monitoring in Recycled Aggregate Concrete Reinforced with Hybrid Steel–Polyolefin Fibers Using Acoustic Emission Technique
The mechanical properties and real-time damage evolution of sustainable concrete (SC) containing 100% recycled concrete aggregate (RCA) under the combined action of hybrid steel and polyolefin fibers were studied. Inspired by solving the massive effects on the environment from construction waste, as well as to improve the lower mechanical performance of lower-grade RCA, the effect of combining high-stiffness hooked-end steel fibers and flexible macro-polyolefin fibers within RCA was investigated. Six different mix designs were considered: plain, single-fiber (100% steel and 100% polyolefin) and three hybrid composites with varying fractions of the steel/polyolefin fibers (25/75, 50/50, and 75/25). Compressive, tensile and flexural strengths were determined by mechanical testing. During compressive testing, the damage evolution was monitored using low-cost acoustic emission (AE) as a non-destructive technique. Cumulative hits analysis, amplitude distributions, and the statistical b-value parameter were used for damage characterization. The results show that steel fiber significantly increased compressive strength (an increase of up to 13.8%), and the 50/50 hybrid mix showed a high synergistic effect, yielding the highest tensile (4.86 MPa) and flexural (25.54 MPa) strengths. AE analysis identified different damage fingerprints: Based on amplitude analysis, steel-fiber composites exhibited high-amplitude events (which may be attributable to fiber pull-out); polyolefin-fiber composites generated medium-amplitude events (may have resulted from distributed microcracking); and hybrid mixes displayed a mixed amplitude distribution. The b-value analysis provided insight into progressive damage and revealed that the hybrid fibers induce stable, diffuse damage that prevents the brittle failure of plain recycled aggregate concrete (RAC). The results show that hybrid fiber reinforcement can be a reliable approach to enhance the mechanical performance and crack resistance of RAC. Furthermore, low-cost acoustic emission (AE) serves as an effective non-destructive method for monitoring damage progression within the material.
- 1 March 2026
- Published by Ital Publication in Civil Engineering Journal
- Vol. 12 (3) , 1190-1204
Experimental Study of Cold-Formed Steel Bridge Girder in Various Shapes Under Static Loads
To facilitate accelerated bridge construction and reduce the cost of bridge design and construction, a cold-formed steel composite bridge girder has been suggested recently as an economical alternative. The new technology for the composite bridge girder includes a cold-formed steel plate and either a precast or cast-in-place reinforced concrete (RC) slab. Previous research on cold-formed steel concrete composite girders has introduced two new shapes for short-span bridge girders: a cold-formed steel tub girder and a folded plate girder system. No study has been conducted on the impact of shape on the static structural behavior of cold-formed composite girders for short-span bridges. This paper investigated the behavior of the cold-formed steel composite girders with different shapes in terms of ductility, stiffness, the ultimate failure load, crack resistance, and interfacial slip. Four shapes were carried out in this research: tub, open-box, and double C with and without lips. Six simply supported girder specimens were designed, fabricated, and subjected to static load tests. The results showed that the cold-formed steel double C lipped girder increased the ultimate load by 12.12% compared to the cold-formed steel tub girder. Additionally, the initial stiffness of the cold-formed steel double C girder increased by 21% compared to the cold-formed steel tub girder. The open-box shape specimen can effectively improve the cracking resistance of cold-formed steel composite girders compared to the cold-formed steel tub girders.
- 1 March 2026
- Published by Ital Publication in Civil Engineering Journal
- Vol. 12 (3) , 1190-1204
Experimental Study of Cold-Formed Steel Bridge Girder in Various Shapes Under Static Loads
To facilitate accelerated bridge construction and reduce the cost of bridge design and construction, a cold-formed steel composite bridge girder has been suggested recently as an economical alternative. The new technology for the composite bridge girder includes a cold-formed steel plate and either a precast or cast-in-place reinforced concrete (RC) slab. Previous research on cold-formed steel concrete composite girders has introduced two new shapes for short-span bridge girders: a cold-formed steel tub girder and a folded plate girder system. No study has been conducted on the impact of shape on the static structural behavior of cold-formed composite girders for short-span bridges. This paper investigated the behavior of the cold-formed steel composite girders with different shapes in terms of ductility, stiffness, the ultimate failure load, crack resistance, and interfacial slip. Four shapes were carried out in this research: tub, open-box, and double C with and without lips. Six simply supported girder specimens were designed, fabricated, and subjected to static load tests. The results showed that the cold-formed steel double C lipped girder increased the ultimate load by 12.12% compared to the cold-formed steel tub girder. Additionally, the initial stiffness of the cold-formed steel double C girder increased by 21% compared to the cold-formed steel tub girder. The open-box shape specimen can effectively improve the cracking resistance of cold-formed steel composite girders compared to the cold-formed steel tub girders.
- Open Access
Tension Lap Splices in Recycled-Aggregate Concrete Strengthened with Steel–Polyolefin Fibers
The bond strength of tension lap splices in recycled-coarse-aggregate-reinforced concrete strengthened with hybrid (steel–polyolefin) fibers was experimentally investigated. This study was conducted with the help of twelve lap-spliced beam specimens. The replacement level of coarse natural aggregates with recycled concrete aggregate (RCA) was 100%. The following variables were investigated: various ranges of steel–polyolefin fibers—100–0%, 75–25%, 50–50%, 25–75%, and 0–100%—in which the total volume fraction of fibers () remains constant at 1%; and two lengths of lap splices for rebars of 16 mm diameter (): 10 and 15 . The test results showed that the best range of steel–polyolefin fibers that gave the highest bond strength was 50–50%. The ductility of the fiber-reinforced recycled-aggregate (FR-RA) concrete was significantly improved for all the cases of various relative ratios of steel and polyolefin fibers. The bond strength was also predicted using three empirical equations proposed by Orangun et al., Darwin et al., and Harajli. This study showed that the Harajli equation gave a more accurate estimation of the bond strength of reinforcing bars embedded in FR-RA concrete than those proposed by Orangun et al. and Darwin et al.Open AccessTension Lap Splices in Recycled-Aggregate Concrete Strengthened with Steel–Polyolefin Fibers
The bond strength of tension lap splices in recycled-coarse-aggregate-reinforced concrete strengthened with hybrid (steel–polyolefin) fibers was experimentally investigated. This study was conducted with the help of twelve lap-spliced beam specimens. The replacement level of coarse natural aggregates with recycled concrete aggregate (RCA) was 100%. The following variables were investigated: various ranges of steel–polyolefin fibers—100–0%, 75–25%, 50–50%, 25–75%, and 0–100%—in which the total volume fraction of fibers () remains constant at 1%; and two lengths of lap splices for rebars of 16 mm diameter (): 10 and 15 . The test results showed that the best range of steel–polyolefin fibers that gave the highest bond strength was 50–50%. The ductility of the fiber-reinforced recycled-aggregate (FR-RA) concrete was significantly improved for all the cases of various relative ratios of steel and polyolefin fibers. The bond strength was also predicted using three empirical equations proposed by Orangun et al., Darwin et al., and Harajli. This study showed that the Harajli equation gave a more accurate estimation of the bond strength of reinforcing bars embedded in FR-RA concrete than those proposed by Orangun et al. and Darwin et al. - Open Access
Carbon Fiber-Reinforced Polymer Composites Integrated Beam–Column Joints with Improved Strength Performance against Seismic Events: Numerical Model Simulation
Strength enhancement of non-seismic concrete beam–column joints (NSCBCJs) via carbon fiber-reinforced polymer composites (CFRPCs) integration has become a viable strategy. However, the implementation of these NSCBCJs without transverse reinforcement shows poor performance during earthquakes in seismic locations. Thus, strengthening the anti-seismic performance of NSCBCJs to meet the acceptance criteria of ACI 374.1-05 is fundamentally significant. Yet, in addition to limited experimental results, only a few numerical studies based on the finite element model have been performed to determine the anti-seismic behavior of NSCBCJs. Consequently, the stress contribution of CFRPCs to NSCBCJs is not clearly understood. Therefore, we used a finite element model to examine the strength contribution of CFRPCs to NSCBCJs. The performance of the proposed finite element model was validated using the experimental results, demonstrating a good agreement between them. It was shown that the strength of NSCBCJs was improved due to CFRPC incorporation, thereby achieving compliance with the seismic requirements of ACI 374.1-05. In addition, CFRPCs presence could enhance the confinement, reduce the deformation of the NSCBCJs and, thus, decrease their stiffness and strength degradation, while simultaneously improving the energy dissipation.
Open AccessCarbon Fiber-Reinforced Polymer Composites Integrated Beam–Column Joints with Improved Strength Performance against Seismic Events: Numerical Model Simulation
Strength enhancement of non-seismic concrete beam–column joints (NSCBCJs) via carbon fiber-reinforced polymer composites (CFRPCs) integration has become a viable strategy. However, the implementation of these NSCBCJs without transverse reinforcement shows poor performance during earthquakes in seismic locations. Thus, strengthening the anti-seismic performance of NSCBCJs to meet the acceptance criteria of ACI 374.1-05 is fundamentally significant. Yet, in addition to limited experimental results, only a few numerical studies based on the finite element model have been performed to determine the anti-seismic behavior of NSCBCJs. Consequently, the stress contribution of CFRPCs to NSCBCJs is not clearly understood. Therefore, we used a finite element model to examine the strength contribution of CFRPCs to NSCBCJs. The performance of the proposed finite element model was validated using the experimental results, demonstrating a good agreement between them. It was shown that the strength of NSCBCJs was improved due to CFRPC incorporation, thereby achieving compliance with the seismic requirements of ACI 374.1-05. In addition, CFRPCs presence could enhance the confinement, reduce the deformation of the NSCBCJs and, thus, decrease their stiffness and strength degradation, while simultaneously improving the energy dissipation.
- Open Access
- 24 January 2024
- Published by International Academic Institute for Science and Technology in International Academic Journal of Science and Engineering
- Vol. 11 (1) , 332-350
Revisiting the Versatility of Seismic Load-enabled Reinforced Concrete Beam Column Linkage
In the seismic load-facilitated (vertical and lateral) reinforced concrete beam-column (RCBC), strong linkages are vital to protect the integrity of any civil structure foundation. Compared to other structural components, these joints often collapse during an earthquake in the seismic locations due to plastic-hinge zone mechanism. Most of the earlier reports on these issues mainly focused on two-dimensional RCBC joints and seldom emphasized on the need of three-dimensional RCBC linkages. Based on this fact, we critically overviewed several recent-state-of-the-art studies carried out on the improvement of RCBC linkages subjected to seismic loading. A careful evaluation of these articles revealed that the factors like shear strength (SS), failure, processing and selection of materials, as well as methods of strengthening (MS) of these RCBC joints are responsible for the collapse. It is established that for low axial load the ductility and bending resistance of the column must be enhanced to strengthen the RCBC links, enabling the diagonal strips or bars more robust than vertical ones and vice versa. Briefly, this article may provide the taxonomy for navigating the researchers into this field, leading to future sustainable development in the civil engineering construction sectors.
- 24 January 2024
- Published by International Academic Institute for Science and Technology in International Academic Journal of Science and Engineering
- Vol. 11 (1) , 332-350
Open AccessRevisiting the Versatility of Seismic Load-enabled Reinforced Concrete Beam Column Linkage
In the seismic load-facilitated (vertical and lateral) reinforced concrete beam-column (RCBC), strong linkages are vital to protect the integrity of any civil structure foundation. Compared to other structural components, these joints often collapse during an earthquake in the seismic locations due to plastic-hinge zone mechanism. Most of the earlier reports on these issues mainly focused on two-dimensional RCBC joints and seldom emphasized on the need of three-dimensional RCBC linkages. Based on this fact, we critically overviewed several recent-state-of-the-art studies carried out on the improvement of RCBC linkages subjected to seismic loading. A careful evaluation of these articles revealed that the factors like shear strength (SS), failure, processing and selection of materials, as well as methods of strengthening (MS) of these RCBC joints are responsible for the collapse. It is established that for low axial load the ductility and bending resistance of the column must be enhanced to strengthen the RCBC links, enabling the diagonal strips or bars more robust than vertical ones and vice versa. Briefly, this article may provide the taxonomy for navigating the researchers into this field, leading to future sustainable development in the civil engineering construction sectors.
- Open Access
Effect of Macro Polyolefin Fibers on Bond Strength of Tension Lap Splices in RC Beams
The effect of macro synthetic polyolefin fibers on the bond strength of tension lap splices in reinforced concrete (RC) beams is investigated in this study. The bond between the reinforcement and concrete plays a vital role in the strength of RC beams. The presence of polyolefin fibers in the lap splice zone confines the concrete and enhances the bond strength of the steel bars. The use of synthetic fibers is preferable to steel ones since steel suffers from corrosion over time. Tests were conducted on 12 full-scale beam specimens to determine the effect of fiber volume fraction (Vf), bar diameter (db) and concrete cover-to-bar diameter (c/db) on the response. Four volume fractions (Vf = 0, 0.5, 1 and 1.5%) of polyolefin fibers and three bar sizes (db = 16, 20 and 25 mm) with the corresponding (c/db = 2.31, 1.75 and 1.30) were considered to evaluate the bond strength. The test results demonstrated that the polyolefin fibers noticeably enhanced the bond strength and ductility of spliced tension bars. Experimental results were compared with those obtained from two theoretical methods including ACI Committee 318 design provisions. The results showed that the equation proposed by the ACI Committee overestimates the bond strength.
Open AccessEffect of Macro Polyolefin Fibers on Bond Strength of Tension Lap Splices in RC Beams
The effect of macro synthetic polyolefin fibers on the bond strength of tension lap splices in reinforced concrete (RC) beams is investigated in this study. The bond between the reinforcement and concrete plays a vital role in the strength of RC beams. The presence of polyolefin fibers in the lap splice zone confines the concrete and enhances the bond strength of the steel bars. The use of synthetic fibers is preferable to steel ones since steel suffers from corrosion over time. Tests were conducted on 12 full-scale beam specimens to determine the effect of fiber volume fraction (Vf), bar diameter (db) and concrete cover-to-bar diameter (c/db) on the response. Four volume fractions (Vf = 0, 0.5, 1 and 1.5%) of polyolefin fibers and three bar sizes (db = 16, 20 and 25 mm) with the corresponding (c/db = 2.31, 1.75 and 1.30) were considered to evaluate the bond strength. The test results demonstrated that the polyolefin fibers noticeably enhanced the bond strength and ductility of spliced tension bars. Experimental results were compared with those obtained from two theoretical methods including ACI Committee 318 design provisions. The results showed that the equation proposed by the ACI Committee overestimates the bond strength.
- Open Access
The Role of Fiber-Type Reinforcement in the Torsional Behavior of Solid and Hollow Reinforced Concrete Beams
In order to improve the strength of concrete structures, the fiber reinforcement of concrete has become an essential factor. This study was conducted as an experimental program to gain a better understanding of how the variance of fiber shape and type affect the structural performance of solid and hollow reinforced concrete beams using four types of fiber (hooked-end, straight, corrugated steel fiber, and polyolefin fiber) under torsion. For this purpose, ten fiber-reinforced concrete beam specimens, five solid and five hollow, with square cross sections were fabricated using the adopted types of fiber. The role of fiber type in the improvement of the mechanical properties of hardened concrete was also investigated. The results revealed that the mechanical properties of the hardened concrete mix was enhanced by using the existing fiber in concrete, and the higher improvement was shown in the splitting tensile strength test and modulus of rapture in specimens with corrugated steel fiber. The torsional behavior of solid and hollow beams was improved significantly, and the capacity of torsional strength was especially improved for the beams strengthened with corrugated steel fiber. Straight and polyolefin fiber showed a slight improvement in the concrete mechanical properties and less enhancement in the torsional capacity of the tested beams. However, the tested beams reinforced by polyolefin fiber provide better ductility under torsion compared with the use of other types of fiber.
Open AccessThe Role of Fiber-Type Reinforcement in the Torsional Behavior of Solid and Hollow Reinforced Concrete Beams
In order to improve the strength of concrete structures, the fiber reinforcement of concrete has become an essential factor. This study was conducted as an experimental program to gain a better understanding of how the variance of fiber shape and type affect the structural performance of solid and hollow reinforced concrete beams using four types of fiber (hooked-end, straight, corrugated steel fiber, and polyolefin fiber) under torsion. For this purpose, ten fiber-reinforced concrete beam specimens, five solid and five hollow, with square cross sections were fabricated using the adopted types of fiber. The role of fiber type in the improvement of the mechanical properties of hardened concrete was also investigated. The results revealed that the mechanical properties of the hardened concrete mix was enhanced by using the existing fiber in concrete, and the higher improvement was shown in the splitting tensile strength test and modulus of rapture in specimens with corrugated steel fiber. The torsional behavior of solid and hollow beams was improved significantly, and the capacity of torsional strength was especially improved for the beams strengthened with corrugated steel fiber. Straight and polyolefin fiber showed a slight improvement in the concrete mechanical properties and less enhancement in the torsional capacity of the tested beams. However, the tested beams reinforced by polyolefin fiber provide better ductility under torsion compared with the use of other types of fiber.
- Open Access
- 30 June 2022
- Published by International University of Sarajevo in Periodicals of Engineering and Natural Sciences (PEN)
- Vol. 10 (3) , 422-434
Compressive strength assessment of normal and self-compacting concrete made with recycled coarse aggregate using in-situ tests
There is an increasing trend in construction for using recycled coarse aggregate (RCA) concrete, which is a more sustainable approach for reducing natural resource consumption. One typical method for developing more environmentally friendly structures is to partially substitute natural aggregate. limited studies investigated the use of in-situ tests to assess the compressive strength of concrete made with RCAs. In this study, ultrasonic pulse velocity (UPV) and core sampling (CST) tests were used to evaluate the compressive strength of normal vibrated (NVC) and self-compacting (SCC) concretes made with recycled coarse aggregates (RCAs). Four different compressive strengths ranging from 25 to 55 MPa were adopted for each concrete type to consider the effect of replacing 0, 20%, 40%, 60%, 80%, and 100% of the required natural coarse aggregates (NCAs) with (RCAs). Exponential relationships were adopted to relate the UPV values with the compressive strength for both RCA-NVC and RCA-SCC. Also, suggested factors were adopted to correct equivalent core strengths for both RCA-NVC and RCA-SCC. The results of both test methods (UPV) and (CST) showed good correlations to estimate the compressive strength of RCA-NVC and RCA-SCC with confidence limits of 93%.
- 30 June 2022
- Published by International University of Sarajevo in Periodicals of Engineering and Natural Sciences (PEN)
- Vol. 10 (3) , 422-434
Open AccessCompressive strength assessment of normal and self-compacting concrete made with recycled coarse aggregate using in-situ tests
There is an increasing trend in construction for using recycled coarse aggregate (RCA) concrete, which is a more sustainable approach for reducing natural resource consumption. One typical method for developing more environmentally friendly structures is to partially substitute natural aggregate. limited studies investigated the use of in-situ tests to assess the compressive strength of concrete made with RCAs. In this study, ultrasonic pulse velocity (UPV) and core sampling (CST) tests were used to evaluate the compressive strength of normal vibrated (NVC) and self-compacting (SCC) concretes made with recycled coarse aggregates (RCAs). Four different compressive strengths ranging from 25 to 55 MPa were adopted for each concrete type to consider the effect of replacing 0, 20%, 40%, 60%, 80%, and 100% of the required natural coarse aggregates (NCAs) with (RCAs). Exponential relationships were adopted to relate the UPV values with the compressive strength for both RCA-NVC and RCA-SCC. Also, suggested factors were adopted to correct equivalent core strengths for both RCA-NVC and RCA-SCC. The results of both test methods (UPV) and (CST) showed good correlations to estimate the compressive strength of RCA-NVC and RCA-SCC with confidence limits of 93%.
- Open Access
- 6 May 2022
- Published by International University of Sarajevo in Periodicals of Engineering and Natural Sciences (PEN)
- Vol. 10 (3) , 422-434
Compressive Strength Assessment of Normal and Self-Compacting Concrete Made with Recycled Coarse Aggregate Using In-Situ Tests
There is an increasing trend in construction for using recycled coarse aggregate (RCA) concrete, which is a more sustainable approach for reducing natural resource consumption. One typical method for developing more environmentally friendly structures is to partially substitute natural aggregate. limited studies investigated the use of in-situ tests to assess the compressive strength of concrete made with RCAs. In this study, ultrasonic pulse velocity (UPV) and core sampling (CST) tests were used to evaluate the compressive strength of normal vibrated (NVC) and self-compacting (SCC) concretes made with recycled coarse aggregates (RCAs). Four different compressive strengths ranging from 25 to 55 MPa were adopted for each concrete type to consider the effect of replacing 0, 20%, 40%, 60%, 80%, and 100% of the required natural coarse aggregates (NCAs) with (RCAs). Exponential relationships were adopted to relate the UPV values with the compressive strength for both RCA-NVC and RCA-SCC. Also, suggested factors were adopted to correct equivalent core strengths for both RCA-NVC and RCA-SCC. The results of both test methods (UPV) and (CST) showed good correlations to estimate the compressive strength of RCA-NVC and RCA-SCC with confidence limits of 93%.
- 6 May 2022
- Published by International University of Sarajevo in Periodicals of Engineering and Natural Sciences (PEN)
- Vol. 10 (3) , 422-434
Open AccessCompressive Strength Assessment of Normal and Self-Compacting Concrete Made with Recycled Coarse Aggregate Using In-Situ Tests
There is an increasing trend in construction for using recycled coarse aggregate (RCA) concrete, which is a more sustainable approach for reducing natural resource consumption. One typical method for developing more environmentally friendly structures is to partially substitute natural aggregate. limited studies investigated the use of in-situ tests to assess the compressive strength of concrete made with RCAs. In this study, ultrasonic pulse velocity (UPV) and core sampling (CST) tests were used to evaluate the compressive strength of normal vibrated (NVC) and self-compacting (SCC) concretes made with recycled coarse aggregates (RCAs). Four different compressive strengths ranging from 25 to 55 MPa were adopted for each concrete type to consider the effect of replacing 0, 20%, 40%, 60%, 80%, and 100% of the required natural coarse aggregates (NCAs) with (RCAs). Exponential relationships were adopted to relate the UPV values with the compressive strength for both RCA-NVC and RCA-SCC. Also, suggested factors were adopted to correct equivalent core strengths for both RCA-NVC and RCA-SCC. The results of both test methods (UPV) and (CST) showed good correlations to estimate the compressive strength of RCA-NVC and RCA-SCC with confidence limits of 93%.
- Open Access
Shear Strength of Headed Stud Connectors in Self-Compacting Concrete with Recycled Coarse Aggregate
This study investigated the use of self-compacting concrete (SCC) made with recycled coarse aggregates (RCAs), which represents a trend of producing environment-friendly concrete, integrated with hot-rolled steel sections by means of headed stud shear connectors in composite structures. Therefore, thirty-six push-out test specimens were examined to assess the shear strength and behavior of the headed stud connectors embedded in RCA-SCC, with the concrete compressive strength, stud diameter, and RCA ratio as the main variables. Four ratios of RCAs ranging from 0 to 60% were used to produce concrete with three different compressive strengths (25, 33, and 40 MPa) for each one. It was found that the use of SCC with RCAs had a negative effect on the shear strength of headed stud connectors. This negative effect could be reduced by increasing the concrete compressive strength and/or the stud diameter. Similarly, a reduction in the shear stiffness of the tested specimens was inversely proportional to the RCA ratio, while the ultimate slip was directly proportional to the RCA ratio. An evaluation of the test results was made by comparing them with those determined by Eurocode 4 and AASHTO LRFD.
Open AccessShear Strength of Headed Stud Connectors in Self-Compacting Concrete with Recycled Coarse Aggregate
This study investigated the use of self-compacting concrete (SCC) made with recycled coarse aggregates (RCAs), which represents a trend of producing environment-friendly concrete, integrated with hot-rolled steel sections by means of headed stud shear connectors in composite structures. Therefore, thirty-six push-out test specimens were examined to assess the shear strength and behavior of the headed stud connectors embedded in RCA-SCC, with the concrete compressive strength, stud diameter, and RCA ratio as the main variables. Four ratios of RCAs ranging from 0 to 60% were used to produce concrete with three different compressive strengths (25, 33, and 40 MPa) for each one. It was found that the use of SCC with RCAs had a negative effect on the shear strength of headed stud connectors. This negative effect could be reduced by increasing the concrete compressive strength and/or the stud diameter. Similarly, a reduction in the shear stiffness of the tested specimens was inversely proportional to the RCA ratio, while the ultimate slip was directly proportional to the RCA ratio. An evaluation of the test results was made by comparing them with those determined by Eurocode 4 and AASHTO LRFD.