Olivier Bonneau
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Olivier Bonneau has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Mihai Arghir
Institut PPRIME, UPR CNRS 3346, Université de Poitiers , 11 Boulevard Marie et Pierre Curie, Chasseneuil-du-Poitou 86360, France
18 shared publications Jean Frêne
Laboratoire de Mécanique des Solides, UMR 6610, SP2MI, Boulevard Marie et Pierre Curie, Téléport 2, BP 30179, 86962 Futuroscope-Chasseneuil Cedex, France
5 shared publicationsCyril Defaye
LaMCoS (UMR CNRS 5259) , INSA LYON , 69621, Villeurbanne, France
4 shared publicationsLaurent Rudloff
Institut PPRIME, CNRS UPR3346 Université de Poitiers, France
4 shared publications- Sébastien Berger
Univ Orleans, Univ Tours, INSA CVL, LaMe EA 7494, 3 Rue Chocolaterie, F-41034 Blois, Loir & Cher, France
4 shared publications Jean Frene
3 shared publications
Latest Publications
- 19 August 2018
- Published by Springer Nature
- p. 335-346
Measurements of Rotordynamic Force Coefficients of Metallic Type Brush Seals
- 19 August 2018
- Published by Springer Nature
- p. 335-346
Measurements of Rotordynamic Force Coefficients of Metallic Type Brush Seals
- 5 July 2018
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 140 (11) , 112501
Experimental and Theoretical Rotordynamic Coefficients of Smooth and Round-Hole Pattern Water-Fed Annular Seals
This work presents the comparison between experimental and theoretical results obtained for three straight annular seals. One of the annular seals has smooth rotor and stator while the others have a textured stator; the textures are equally spaced shallow round holes, with two different depths. The experimental results were obtained on a test rig dedicated to the identification of the dynamic coefficients of high Reynolds bearings and annular seals. The test rig uses hot water (<50 °C) as a working fluid. Dynamic excitations imposed by piezoelectric shakers to the rotor enable the identification of dynamic coefficients via complex impedances. Theoretical results compared with experimental findings were obtained by numerically solving the “bulk flow” equations (film thickness averaged equations dominated by inertia effects). The numerical model was extensively validated for smooth annular seals but is less confident for textured surfaces. The present comparisons between experimental and numerical results enable to estimate the accuracy of the numerical model employed for the textured seals.
- 5 July 2018
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 140 (11) , 112501
Experimental and Theoretical Rotordynamic Coefficients of Smooth and Round-Hole Pattern Water-Fed Annular Seals
This work presents the comparison between experimental and theoretical results obtained for three straight annular seals. One of the annular seals has smooth rotor and stator while the others have a textured stator; the textures are equally spaced shallow round holes, with two different depths. The experimental results were obtained on a test rig dedicated to the identification of the dynamic coefficients of high Reynolds bearings and annular seals. The test rig uses hot water (<50 °C) as a working fluid. Dynamic excitations imposed by piezoelectric shakers to the rotor enable the identification of dynamic coefficients via complex impedances. Theoretical results compared with experimental findings were obtained by numerically solving the “bulk flow” equations (film thickness averaged equations dominated by inertia effects). The numerical model was extensively validated for smooth annular seals but is less confident for textured surfaces. The present comparisons between experimental and numerical results enable to estimate the accuracy of the numerical model employed for the textured seals.
- 3 March 2016
- Published by Taylor & Francis in Tribology Transactions
- Vol. 59 (2) , 208-218
A Volume of Fluid Method for Air Ingestion in Squeeze Film Dampers
The present work introduces a numerical model for squeeze film dampers (SFDs) operating simultaneously with vapor cavitation and air ingestion. The pressure is given by the Reynolds equation. The vapor cavitation model used in this work is based on Rayleigh-Plesset equation and was previously presented. Air ingestion occurring in open-end SFDs is dealt with by using a volume of fluid computational fluid dynamics (CFD) method not previously employed in lubrication problems. The original volume of fluid (VOF) method proposed by Hirt and Nichols was adapted to capture and track the free boundary between air and liquid in a thin-film lubricant. Numerical results are compared with experimental data of Adiletta and Pietra showing the simultaneous influence of vapor cavitation and air ingestion in an open-end SFD. These two phenomena have typical pressure values and appear at different locations and with a different extent. The vapor threshold is located on the low-pressure zone and is the lowest pressure value in the SFD, usually close to absolute zero. The air ingestion is characterized by a zone of almost constant pressure, usually close to atmospheric pressure (or, more generally, equal to the outer, exit pressure) and located between the minimum and the maximum pressures in the SFD. The numerical model proposed in this article deals simultaneously with these two effects. A simplified version of the air ingestion model for standard SFD applications is also introduced.
- 3 March 2016
- Published by Taylor & Francis in Tribology Transactions
- Vol. 59 (2) , 208-218
A Volume of Fluid Method for Air Ingestion in Squeeze Film Dampers
The present work introduces a numerical model for squeeze film dampers (SFDs) operating simultaneously with vapor cavitation and air ingestion. The pressure is given by the Reynolds equation. The vapor cavitation model used in this work is based on Rayleigh-Plesset equation and was previously presented. Air ingestion occurring in open-end SFDs is dealt with by using a volume of fluid computational fluid dynamics (CFD) method not previously employed in lubrication problems. The original volume of fluid (VOF) method proposed by Hirt and Nichols was adapted to capture and track the free boundary between air and liquid in a thin-film lubricant. Numerical results are compared with experimental data of Adiletta and Pietra showing the simultaneous influence of vapor cavitation and air ingestion in an open-end SFD. These two phenomena have typical pressure values and appear at different locations and with a different extent. The vapor threshold is located on the low-pressure zone and is the lowest pressure value in the SFD, usually close to absolute zero. The air ingestion is characterized by a zone of almost constant pressure, usually close to atmospheric pressure (or, more generally, equal to the outer, exit pressure) and located between the minimum and the maximum pressures in the SFD. The numerical model proposed in this article deals simultaneously with these two effects. A simplified version of the air ingestion model for standard SFD applications is also introduced.
- 28 June 2014
- Published by David Publishing Company in Journal of Mechanics Engineering and Automation
- Vol. 4 (6)
Dynamic Control of a Flexible Shaft Mounted in Adaptive or Active Bearing
- 28 June 2014
- Published by David Publishing Company in Journal of Mechanics Engineering and Automation
- Vol. 4 (6)
Dynamic Control of a Flexible Shaft Mounted in Adaptive or Active Bearing
- 16 June 2014
- Published by ASME International
Experimental and Theoretical Rotordynamic Coefficients of Smooth and Round-Hole Pattern Water Fed Annular Seals
The present work presents the comparison between experimental and theoretical results obtained for three straight annular seals. One of the annular seals has smooth rotor and stator while the others have a textured stator; the textures are equally spaced shallow round holes, with two different depths. The experimental results were obtained on a test rig dedicated to the identification of the dynamic coefficients of high Reynolds bearings and annular seals. The test rig uses hot water (<50°C) as a working fluid. Dynamic excitations imposed by piezoelectric shakers to the rotor enable the identification of dynamic coefficients via complex impedances. Theoretical results compared with experimental findings were obtained by numerically solving the “Bulk Flow” equations (film thickness averaged equations dominated by inertia effects). The numerical model was extensively validated for smooth annular seals but is less confident for textured surfaces. The present comparisons between experimental and numerical results enable to estimate the accuracy of the numerical model employed for the textured seals.
- 16 June 2014
- Published by ASME International
Experimental and Theoretical Rotordynamic Coefficients of Smooth and Round-Hole Pattern Water Fed Annular Seals
The present work presents the comparison between experimental and theoretical results obtained for three straight annular seals. One of the annular seals has smooth rotor and stator while the others have a textured stator; the textures are equally spaced shallow round holes, with two different depths. The experimental results were obtained on a test rig dedicated to the identification of the dynamic coefficients of high Reynolds bearings and annular seals. The test rig uses hot water (<50°C) as a working fluid. Dynamic excitations imposed by piezoelectric shakers to the rotor enable the identification of dynamic coefficients via complex impedances. Theoretical results compared with experimental findings were obtained by numerically solving the “Bulk Flow” equations (film thickness averaged equations dominated by inertia effects). The numerical model was extensively validated for smooth annular seals but is less confident for textured surfaces. The present comparisons between experimental and numerical results enable to estimate the accuracy of the numerical model employed for the textured seals.
- 26 April 2013
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 227 (8) , 905-911
Identification of stiffness and damping coefficients of hydrostatic bearing with angled injection
This study deals with the experimental results obtained for a hydrostatic/hydrodynamic bearing used in aerospace turbopumps. This supporting element, if fitted with angled injection directed against shaft rotation, can provide a stabilizing effect to the rotor by reducing the circumferential flow. In order to characterize this effect and to improve its numerical simulation, an experimental housing has been designed to test the three directions of injection (radial, 25° and 50°). Measurements were obtained for the centered bearing operating at 2 kr/min, 4 kr/min and 6 kr/min with supply pressures of 2.5 MPa, 3.5 MPa and 4.5 MPa. The test rig uses hot water (<50 ℃) as a working fluid. For given operating conditions, a set of dynamic excitations imposed to the rotor provides complex impedances that are used for identifying dynamic coefficients. According to many pressure plugs distributed along the housing, the pattern of the pressure field in the recess and the thin fluid film near the recess is reconstructed. The bearing flow rate is also measured. Static and dynamic experimental results are compared with theoretical results obtained bycombining a pressure pattern model with a bulk-flow analysis. A good agreement between the two methods is observed. The measured cross-coupled stiffness is lower than the predicted one, indicating that the benefits of angled injection are better than what was predicted.
- 26 April 2013
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 227 (8) , 905-911
Identification of stiffness and damping coefficients of hydrostatic bearing with angled injection
This study deals with the experimental results obtained for a hydrostatic/hydrodynamic bearing used in aerospace turbopumps. This supporting element, if fitted with angled injection directed against shaft rotation, can provide a stabilizing effect to the rotor by reducing the circumferential flow. In order to characterize this effect and to improve its numerical simulation, an experimental housing has been designed to test the three directions of injection (radial, 25° and 50°). Measurements were obtained for the centered bearing operating at 2 kr/min, 4 kr/min and 6 kr/min with supply pressures of 2.5 MPa, 3.5 MPa and 4.5 MPa. The test rig uses hot water (<50 ℃) as a working fluid. For given operating conditions, a set of dynamic excitations imposed to the rotor provides complex impedances that are used for identifying dynamic coefficients. According to many pressure plugs distributed along the housing, the pattern of the pressure field in the recess and the thin fluid film near the recess is reconstructed. The bearing flow rate is also measured. Static and dynamic experimental results are compared with theoretical results obtained bycombining a pressure pattern model with a bulk-flow analysis. A good agreement between the two methods is observed. The measured cross-coupled stiffness is lower than the predicted one, indicating that the benefits of angled injection are better than what was predicted.
- 29 June 2012
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 134 (8) , 082503
Experimental Analysis of the Dynamic Characteristics of a Hybrid Aerostatic Bearing
The dynamic characteristics of a hybrid aerostatic bearing are experimentally investigated on a test rig consisting of a rigid rotor driven by an impulse turbine. The rotor is horizontally mounted and is supported by two identical aerostatic bearings. Both the impulse turbine and the aerostatic hybrid bearings are fed with air. The feeding pressures in the bearings can be as high as 7 bars and rotation speeds can reach 60 krpm so the dynamic load on the rotor is much larger than the static load engendered by its weight. Excitations are applied either via an impact hammer or via unbalancing masses. The measuring instruments record the bearing feeding pressures, the rotation speed, the impact force, the displacements of the two bearings, and the bearing housing accelerations. The experimental data together with the equations of motion of the rotor enables the identification of the dynamic coefficients of the bearings. A second identification procedure using the same impact hammer is also possible as force transducers are mounted between the bearing housing and its support. The dynamic coefficients of the bearings can then be obtained from the equation of motion of its housing. Unbalance response provide a convenient way for verifying the accuracy of the identified dynamic coefficients. Therefore these coefficients are injected in the equations of motion of a four degrees of freedom rigid rotor and the theoretical results are compared with values measured on the test rig. Comparisons show that predictions are acceptable but become less accurate at high rotation speeds where large dynamic forces are needed for exciting the corresponding synchronous frequencies.
- 29 June 2012
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 134 (8) , 082503
Experimental Analysis of the Dynamic Characteristics of a Hybrid Aerostatic Bearing
The dynamic characteristics of a hybrid aerostatic bearing are experimentally investigated on a test rig consisting of a rigid rotor driven by an impulse turbine. The rotor is horizontally mounted and is supported by two identical aerostatic bearings. Both the impulse turbine and the aerostatic hybrid bearings are fed with air. The feeding pressures in the bearings can be as high as 7 bars and rotation speeds can reach 60 krpm so the dynamic load on the rotor is much larger than the static load engendered by its weight. Excitations are applied either via an impact hammer or via unbalancing masses. The measuring instruments record the bearing feeding pressures, the rotation speed, the impact force, the displacements of the two bearings, and the bearing housing accelerations. The experimental data together with the equations of motion of the rotor enables the identification of the dynamic coefficients of the bearings. A second identification procedure using the same impact hammer is also possible as force transducers are mounted between the bearing housing and its support. The dynamic coefficients of the bearings can then be obtained from the equation of motion of its housing. Unbalance response provide a convenient way for verifying the accuracy of the identified dynamic coefficients. Therefore these coefficients are injected in the equations of motion of a four degrees of freedom rigid rotor and the theoretical results are compared with values measured on the test rig. Comparisons show that predictions are acceptable but become less accurate at high rotation speeds where large dynamic forces are needed for exciting the corresponding synchronous frequencies.
- 1 June 2011
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 482, 31-38
Identification of the Dynamic Coefficients of Hybrid Bearings
Within the linear region, the oil-film force increment of journal bearing is a fourdegree- of-freedom linear system. This paper presents an experimental method to identify hybrid bearing coefficients. Under various testing conditions described, experimental data are required on a complex test rig. An inverse technique based on least square method in time domain is developped for the coefficients identification. It results from the experimental data exploitation that the linear stiffness and damping coefficients are sensitive to the pressure feed, but the mass coefficients are insensitive.
- 1 June 2011
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 482, 31-38
Identification of the Dynamic Coefficients of Hybrid Bearings
Within the linear region, the oil-film force increment of journal bearing is a fourdegree- of-freedom linear system. This paper presents an experimental method to identify hybrid bearing coefficients. Under various testing conditions described, experimental data are required on a complex test rig. An inverse technique based on least square method in time domain is developped for the coefficients identification. It results from the experimental data exploitation that the linear stiffness and damping coefficients are sensitive to the pressure feed, but the mass coefficients are insensitive.
- 14 April 2011
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 133 (9) , 092501
Experimental Analyses of a First Generation Foil Bearing: Startup Torque and Dynamic Coefficients
This paper presents the results of the experimental analysis of static and dynamic characteristics of a generation 1 foil bearing of 38.1 mm diameter and . The test rig is of floating bearing type, the rigid shaft being mounted on ceramic ball bearings and driven up to 40 krpm. Two different casings are used for startup and for measurement of dynamic coefficients. In its first configuration, the test rig is designed to measure the startup torque. The foil bearing casing is made of two rings separated by a needle bearing to enable an almost torque free rotation between the foil bearing and the static load. The basic results are the startup torque and the lift-off speed. In its second configuration, a different casing is used to measure the impedances of the foil bearing. Misalignment is a problem that is minimized by using three flexible stingers connecting the foil bearing casing to the base plate of the test rig. The test rig enables the application of a static load and of the dynamic excitation on the journal bearing casing and can measure displacements, forces, and accelerations. Working conditions consisted of static loads comprised between 10 N and 50 N and rotation frequencies ranging from 260 Hz to 590 Hz. Excitation frequencies comprised between 100 Hz and 600 Hz are applied by two orthogonally mounted shakers for each working condition. Stiffness and damping coefficients are identified from the complex impedances and enable the calculation of natural frequencies. The experimental results show that the dynamic characteristics of the tested bearing have a weak dependence on the rotation speed but vary with the excitation frequency.- 14 April 2011
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 133 (9) , 092501
Experimental Analyses of a First Generation Foil Bearing: Startup Torque and Dynamic Coefficients
This paper presents the results of the experimental analysis of static and dynamic characteristics of a generation 1 foil bearing of 38.1 mm diameter and . The test rig is of floating bearing type, the rigid shaft being mounted on ceramic ball bearings and driven up to 40 krpm. Two different casings are used for startup and for measurement of dynamic coefficients. In its first configuration, the test rig is designed to measure the startup torque. The foil bearing casing is made of two rings separated by a needle bearing to enable an almost torque free rotation between the foil bearing and the static load. The basic results are the startup torque and the lift-off speed. In its second configuration, a different casing is used to measure the impedances of the foil bearing. Misalignment is a problem that is minimized by using three flexible stingers connecting the foil bearing casing to the base plate of the test rig. The test rig enables the application of a static load and of the dynamic excitation on the journal bearing casing and can measure displacements, forces, and accelerations. Working conditions consisted of static loads comprised between 10 N and 50 N and rotation frequencies ranging from 260 Hz to 590 Hz. Excitation frequencies comprised between 100 Hz and 600 Hz are applied by two orthogonally mounted shakers for each working condition. Stiffness and damping coefficients are identified from the complex impedances and enable the calculation of natural frequencies. The experimental results show that the dynamic characteristics of the tested bearing have a weak dependence on the rotation speed but vary with the excitation frequency.- 1 January 2011
- Published by ASME International
- p. 587-595
Experimental Analysis of Dynamic Characteristics of a Hybrid Aerostatic Bearing
The dynamic characteristics of a hybrid aerostatic bearing are experimentally investigated on a test rig consisting of a rigid rotor driven by an impulse turbine located at its midlength. The rotor is horizontally mounted and is supported by two identical aerostatic bearings at its ends. Both the impulse turbine and the aerostatic hybrid bearings are fed with air. The actually available resources enable to attain feeding pressures up to 5 bar in the bearings and rotation speeds up to 60 krpm. Under these conditions the dynamic load on the rotor is much larger than the static load engendered by its weight. Dynamic loads consist either of impacts provided by a hammer or of added unbalance masses. The test rig can measure the bearing feeding pressures, the rotation speed, the impact force, the displacements of the two bearings and the bearing housing accelerations. This experimental information together with the equations of motion of the rotor enables the identification of the dynamic coefficients of the bearings. A second identification procedure using the same impact hammer is enabled by the fact force transducers are mounted between the bearing housing and its support. The dynamic coefficients of the bearings can then be obtained from the equation of motion of its housing. Unbalance response provide a convenient way for verifying the accuracy of the identified dynamic coefficients. Therefore these coefficients are injected in the equations of motion of a four degrees of freedom rigid rotor and the theoretical results are compared with values measured on the test rig. Comparisons show that predictions are acceptable but become less accurate at high rotation speeds where large dynamic forces are needed for exciting the corresponding synchronous frequencies.
- 1 January 2011
- Published by ASME International
- p. 587-595
Experimental Analysis of Dynamic Characteristics of a Hybrid Aerostatic Bearing
The dynamic characteristics of a hybrid aerostatic bearing are experimentally investigated on a test rig consisting of a rigid rotor driven by an impulse turbine located at its midlength. The rotor is horizontally mounted and is supported by two identical aerostatic bearings at its ends. Both the impulse turbine and the aerostatic hybrid bearings are fed with air. The actually available resources enable to attain feeding pressures up to 5 bar in the bearings and rotation speeds up to 60 krpm. Under these conditions the dynamic load on the rotor is much larger than the static load engendered by its weight. Dynamic loads consist either of impacts provided by a hammer or of added unbalance masses. The test rig can measure the bearing feeding pressures, the rotation speed, the impact force, the displacements of the two bearings and the bearing housing accelerations. This experimental information together with the equations of motion of the rotor enables the identification of the dynamic coefficients of the bearings. A second identification procedure using the same impact hammer is enabled by the fact force transducers are mounted between the bearing housing and its support. The dynamic coefficients of the bearings can then be obtained from the equation of motion of its housing. Unbalance response provide a convenient way for verifying the accuracy of the identified dynamic coefficients. Therefore these coefficients are injected in the equations of motion of a four degrees of freedom rigid rotor and the theoretical results are compared with values measured on the test rig. Comparisons show that predictions are acceptable but become less accurate at high rotation speeds where large dynamic forces are needed for exciting the corresponding synchronous frequencies.