Neville Rebelo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Neville Rebelo has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Huayong Zhao
Wolfson School of Mechanical, Electrical and Manufacturing Engineering, Loughborough University, Leicestershire LE11 3TU, UK
2 shared publications A. Williams
Department of Mechanical Engineering, University of Chester, Chester CH1 4BJ, UK
1 shared publication- Andrew Morgan Williams
Loughborough Univ
1 shared publication Andrew Williams
University of Chester
1 shared publicationC. Garner
Wolfson School of Mechanical, Electrical and Manufacturing Engineering, Loughborough University, Loughborough, Leicestershire LE11 3TU, UK
1 shared publicationColin Garner
Loughborough University
1 shared publication
Latest Publications
- 2 June 2021
- Published by Springer Nature
- p. 191-195
Effect of Bulk Temperature on the Evaporation of a Nitrogen Drop in Different Immiscible Liquids
- 2 June 2021
- Published by Springer Nature
- p. 191-195
Effect of Bulk Temperature on the Evaporation of a Nitrogen Drop in Different Immiscible Liquids
- 22 August 2019
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 143, 118575
Evaporation of liquid nitrogen droplets in superheated immiscible liquids
- 22 August 2019
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 143, 118575
Evaporation of liquid nitrogen droplets in superheated immiscible liquids
- Open Access
- 24 April 2017
- Published by ASME International in Journal of Fluids Engineering
- Vol. 139 (7) , 071104
On the Measurement and Modeling of High-Pressure Flows in Poppet Valves Under Steady-State and Transient Conditions
Flow coefficients of intake valves and port combinations were determined experimentally for a compressed nitrogen engine under steady-state and dynamic flow conditions for inlet pressures up to 3.2 MPa. Variable valve timing was combined with an indexed parked piston cylinder unit for testing valve flows at different cylinder volumes while maintaining realistic in-cylinder transient pressure profiles by simply using a fixed area outlet orifice. A one-dimensional modeling approach describing three-dimensional valve flow characteristics has been developed by the use of variable flow coefficients that take into account the propagation of flow jets and their boundaries as a function of downstream/upstream pressure ratios. The results obtained for the dynamic flow cases were compared with steady-state results for the cylinder to inlet port pressure ratios ranges from 0.18 to 0.83. The deviation of flow coefficients for both cases is discussed using pulsatile flow theory. The key findings include the followings: (1) for a given valve lift, the steady-state flow coefficients fall by up to 21% with increasing cylinder/manifold pressure ratios within the measured range given above and (2) transient flow coefficients deviated from those measured for the steady-state flow as the valve lift increases beyond a critical value of approximately 0.5 mm. The deviation can be due to the insufficient time of the development of steady-state boundary layers, which can be quantified by the instantaneous Womersley number defined by using the transient hydraulic diameter. We show that it is possible to predict deviations of the transient valve flow from the steady-state measurements alone.
- 24 April 2017
- Published by ASME International in Journal of Fluids Engineering
- Vol. 139 (7) , 071104
Open AccessOn the Measurement and Modeling of High-Pressure Flows in Poppet Valves Under Steady-State and Transient Conditions
Flow coefficients of intake valves and port combinations were determined experimentally for a compressed nitrogen engine under steady-state and dynamic flow conditions for inlet pressures up to 3.2 MPa. Variable valve timing was combined with an indexed parked piston cylinder unit for testing valve flows at different cylinder volumes while maintaining realistic in-cylinder transient pressure profiles by simply using a fixed area outlet orifice. A one-dimensional modeling approach describing three-dimensional valve flow characteristics has been developed by the use of variable flow coefficients that take into account the propagation of flow jets and their boundaries as a function of downstream/upstream pressure ratios. The results obtained for the dynamic flow cases were compared with steady-state results for the cylinder to inlet port pressure ratios ranges from 0.18 to 0.83. The deviation of flow coefficients for both cases is discussed using pulsatile flow theory. The key findings include the followings: (1) for a given valve lift, the steady-state flow coefficients fall by up to 21% with increasing cylinder/manifold pressure ratios within the measured range given above and (2) transient flow coefficients deviated from those measured for the steady-state flow as the valve lift increases beyond a critical value of approximately 0.5 mm. The deviation can be due to the insufficient time of the development of steady-state boundary layers, which can be quantified by the instantaneous Womersley number defined by using the transient hydraulic diameter. We show that it is possible to predict deviations of the transient valve flow from the steady-state measurements alone.
- 11 November 2015
- Published by ASME International in Journal of Thermal Science and Engineering Applications
- Vol. 8 (1) , 011011
Pressure Drop Studies on Supercritical Helium Flowing in Horizontal Tubes
Supercritical helium owing to its single-phase characteristics and enhanced heat transfer near the pseudo-critical region is envisaged as a potential coolant for superconducting magnets used in particle accelerators and fusion devices. However, near the transposed critical line, there is a wide fluctuation of thermophysical properties like specific heat at constant pressure, density, thermal conductivity, viscosity, etc. As a consequence of this fluctuation, heat transfer and fluid flow studies become difficult for accurate prediction of heat transfer coefficient and friction factor. In this paper, numerical simulation of supercritical helium flowing under turbulent conditions in a horizontal heated tube is performed using computational fluid dynamics (CFD) software ANSYS FLUENT v12.0.16. It is found that results of pressure drop obtained from simulation closely match experimental data in case of fluctuation free regimes. The friction factor indicating the frictional pressure drop occurring in a horizontal tube can be matched to existing correlations within given accuracies for fluctuation regimes. A correlation for friction factor that yields better results than those in literature is proposed based on the simulation data obtained. The accurate determination of the overall pressure drop in the tubes along with the optimum flow rates gives the estimation of pumping power required for enhanced heat transfer with flow of supercritical helium.
- 11 November 2015
- Published by ASME International in Journal of Thermal Science and Engineering Applications
- Vol. 8 (1) , 011011
Pressure Drop Studies on Supercritical Helium Flowing in Horizontal Tubes
Supercritical helium owing to its single-phase characteristics and enhanced heat transfer near the pseudo-critical region is envisaged as a potential coolant for superconducting magnets used in particle accelerators and fusion devices. However, near the transposed critical line, there is a wide fluctuation of thermophysical properties like specific heat at constant pressure, density, thermal conductivity, viscosity, etc. As a consequence of this fluctuation, heat transfer and fluid flow studies become difficult for accurate prediction of heat transfer coefficient and friction factor. In this paper, numerical simulation of supercritical helium flowing under turbulent conditions in a horizontal heated tube is performed using computational fluid dynamics (CFD) software ANSYS FLUENT v12.0.16. It is found that results of pressure drop obtained from simulation closely match experimental data in case of fluctuation free regimes. The friction factor indicating the frictional pressure drop occurring in a horizontal tube can be matched to existing correlations within given accuracies for fluctuation regimes. A correlation for friction factor that yields better results than those in literature is proposed based on the simulation data obtained. The accurate determination of the overall pressure drop in the tubes along with the optimum flow rates gives the estimation of pumping power required for enhanced heat transfer with flow of supercritical helium.