Philipp A. Heizmann
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Philipp A. Heizmann has a total of 78 co-authors. Here are the top co-authors by number of shared publications:
- Severin Vierrath
Electrochemical Energy Systems, IMTEK – Department of Microsystems Engineering, University of Freiburg, Georges-Koehler-Allee 103, 79110 Freiburg, Germany
10 shared publications - Carolin Klose
University Freiburg Georges-Koehler-Allee 103
4 shared publications - Hien Nguyen
Ionysis GmbH Georges‐Koehler‐Allee 103 79110 Freiburg Germany
4 shared publications - Andreas Münchinger
University Freiburg Georges-Koehler-Allee 103
3 shared publications - Hannes Liepold
Electrochemical Energy Systems, IMTEK Department of Microsystems Engineering, University of Freiburg, Georges-Köhler-Allee 103, 79110 Freiburg, Germany
3 shared publications Matthias Breitwieser
Hahn‐Schickard Georges‐Koehler‐Allee 103 79110 Freiburg Germany
3 shared publications
Latest Publications
- Open Access
- 3 September 2025
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 9 (20) , 5619-5626
Back to black: utilizing unsupported Pt for thin cathodes in PFSA-free PEM fuel cells
Unsupported catalyst nanoparticles in fluorine-free PEMFC electrodes alleviate the protonic versus mass transport resistance trade-off, enhancing overall electrode performance.
- 3 September 2025
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 9 (20) , 5619-5626
Open AccessBack to black: utilizing unsupported Pt for thin cathodes in PFSA-free PEM fuel cells
Unsupported catalyst nanoparticles in fluorine-free PEMFC electrodes alleviate the protonic versus mass transport resistance trade-off, enhancing overall electrode performance.
- Open Access
- 9 October 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (44) , 32358-32369
Pt/C catalysts synthesized in a commercial particle atomic layer deposition system enabling improved durability in fuel cells
Pt/Cs synthesized via particle ALD demonstrate increased PEM fuel cell durability over 30 000 cycles of Pt dissolution testing, attributed to their narrow Pt size distribution and high Pt dispersity.
- 9 October 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (44) , 32358-32369
Open AccessPt/C catalysts synthesized in a commercial particle atomic layer deposition system enabling improved durability in fuel cells
Pt/Cs synthesized via particle ALD demonstrate increased PEM fuel cell durability over 30 000 cycles of Pt dissolution testing, attributed to their narrow Pt size distribution and high Pt dispersity.
- Open Access
- 30 September 2024
- Published by Elsevier in Journal of Power Sources
- Vol. 624
High protonic resistance of hydrocarbon-based cathodes in PEM fuel cells under low humidity conditions: Origin, implication, and mitigation
- 30 September 2024
- Published by Elsevier in Journal of Power Sources
- Vol. 624
Open AccessHigh protonic resistance of hydrocarbon-based cathodes in PEM fuel cells under low humidity conditions: Origin, implication, and mitigation
- Open Access
- 10 June 2024
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 5 (14) , 5724-5737
Adsorptive and photo-Fenton properties of bimetallic MIL-100(Fe,Sn) and MIL-100(Fe,Ir) MOFs toward removal of tetracycline from aqueous solutions
Novel bimetallic MIL-100(Fe,Sn) MOFs and MIL-100(Fe,Ir) MOFs were synthesized and then utilized for efficient treatment of tetracycline-contaminated wastewater.
- 10 June 2024
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 5 (14) , 5724-5737
Open AccessAdsorptive and photo-Fenton properties of bimetallic MIL-100(Fe,Sn) and MIL-100(Fe,Ir) MOFs toward removal of tetracycline from aqueous solutions
Novel bimetallic MIL-100(Fe,Sn) MOFs and MIL-100(Fe,Ir) MOFs were synthesized and then utilized for efficient treatment of tetracycline-contaminated wastewater.
- Open Access
- 1 May 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (5) , 054509
Gas Transport Resistance of Hydrocarbon-Based Catalyst Layers in Proton-Exchange Membrane Fuel Cells
Recent developments in hydrocarbon-based proton exchange membrane fuel cells have significantly narrowed the performance gap compared to state-of-the-art cells using perfluorosulfonic acid ionomers (PFSA). However, balancing protonic resistance and gas transport resistance in the catalyst layer remains a challenge at low humidity. This study investigates gas transport resistance and its components in sulfonated phenylated polyphenylene-based catalyst layers using various limiting current methods. Results show that increasing the dry ionomer to carbon (I/C) ratio from 0.2 to 0.4, a measure to catch up with protonic resistance of PFSA-based catalyst layers, significantly increases gas transport resistance in the cathode catalyst layer by 28 %. The data suggest a strong correlation between local gas transport resistance and IEC. A high IEC is beneficial for the gas transport through the ionomer film. However, at low ionomer volume fractions the local gas transport resistance is dominated by the I/C independent interfacial resistance. Furthermore, a low IEC hydrocarbon ionomer, such as Pemion® PP1-HNN4–00-X (IEC = 2.5 meq g−1), not only exhibits a beneficial interfacial resistance, but also suppresses excessive ionomer swelling, which typically occurs during operating conditions where liquid water is forming.
- 1 May 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (5) , 054509
Open AccessGas Transport Resistance of Hydrocarbon-Based Catalyst Layers in Proton-Exchange Membrane Fuel Cells
Recent developments in hydrocarbon-based proton exchange membrane fuel cells have significantly narrowed the performance gap compared to state-of-the-art cells using perfluorosulfonic acid ionomers (PFSA). However, balancing protonic resistance and gas transport resistance in the catalyst layer remains a challenge at low humidity. This study investigates gas transport resistance and its components in sulfonated phenylated polyphenylene-based catalyst layers using various limiting current methods. Results show that increasing the dry ionomer to carbon (I/C) ratio from 0.2 to 0.4, a measure to catch up with protonic resistance of PFSA-based catalyst layers, significantly increases gas transport resistance in the cathode catalyst layer by 28 %. The data suggest a strong correlation between local gas transport resistance and IEC. A high IEC is beneficial for the gas transport through the ionomer film. However, at low ionomer volume fractions the local gas transport resistance is dominated by the I/C independent interfacial resistance. Furthermore, a low IEC hydrocarbon ionomer, such as Pemion® PP1-HNN4–00-X (IEC = 2.5 meq g−1), not only exhibits a beneficial interfacial resistance, but also suppresses excessive ionomer swelling, which typically occurs during operating conditions where liquid water is forming.
- Open Access
- 15 June 2023
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 13 (27) , 18916-18926
Carbon black supported Ag nanoparticles in zero-gap CO2 electrolysis to CO enabling high mass activity
In this study Ag nanoparticles supported on carbon black (Ag/C) were studied as catalysts for the electrochemical reduction of CO2 to CO.
- 15 June 2023
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 13 (27) , 18916-18926
Open AccessCarbon black supported Ag nanoparticles in zero-gap CO2 electrolysis to CO enabling high mass activity
In this study Ag nanoparticles supported on carbon black (Ag/C) were studied as catalysts for the electrochemical reduction of CO2 to CO.
- Open Access
- 31 January 2023
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 13 (7) , 4601-4611
Alternative and facile production pathway towards obtaining high surface area PtCo/C intermetallic catalysts for improved PEM fuel cell performance
The design of catalysts with stable and finely dispersed platinum or platinum alloy nanoparticles on the carbon support is key in controlling the performance of proton exchange membrane (PEM) fuel cells. In the present work, an intermetallic PtCo/C catalyst is synthesized via double-passivation galvanic displacement. TEM and XRD confirm a significantly narrowed particle size distribution for the catalyst particles compared to commercial benchmark catalysts (Umicore PtCo/C). Only about 10% of the mass fraction of PtCo particles show a diameter larger than 8 nm, whereas this is up to or even more than 35% for the reference systems. This directly results in a considerable increase in electrochemically active surface area (96 m2 g−1 vs. >70 m2 g−1), which confirms the more efficient usage of precious catalyst metal in the novel catalyst. Single-cell tests validate this finding by improved PEM fuel cell performance. Reducing the cathode catalyst loading from 0.4 mg cm−2 to 0.25 mg cm−2 resulted in a power density drop at an application-relevant 0.7 V of only 4% for the novel catalyst, compared to the 10% and 20% for the commercial benchmarks reference catalysts.
- 31 January 2023
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 13 (7) , 4601-4611
Open AccessAlternative and facile production pathway towards obtaining high surface area PtCo/C intermetallic catalysts for improved PEM fuel cell performance
The design of catalysts with stable and finely dispersed platinum or platinum alloy nanoparticles on the carbon support is key in controlling the performance of proton exchange membrane (PEM) fuel cells. In the present work, an intermetallic PtCo/C catalyst is synthesized via double-passivation galvanic displacement. TEM and XRD confirm a significantly narrowed particle size distribution for the catalyst particles compared to commercial benchmark catalysts (Umicore PtCo/C). Only about 10% of the mass fraction of PtCo particles show a diameter larger than 8 nm, whereas this is up to or even more than 35% for the reference systems. This directly results in a considerable increase in electrochemically active surface area (96 m2 g−1 vs. >70 m2 g−1), which confirms the more efficient usage of precious catalyst metal in the novel catalyst. Single-cell tests validate this finding by improved PEM fuel cell performance. Reducing the cathode catalyst loading from 0.4 mg cm−2 to 0.25 mg cm−2 resulted in a power density drop at an application-relevant 0.7 V of only 4% for the novel catalyst, compared to the 10% and 20% for the commercial benchmarks reference catalysts.
- Open Access
- 13 November 2022
- Published by Wiley in Advanced Sustainable Systems
- Vol. 7 (2)
Toward Scalable Production: Catalyst‐Coated Membranes (CCMs) for Anion‐Exchange Membrane Water Electrolysis via Direct Bar Coating
Direct catalyst coating of membranes is an obvious membrane‐electrode assembly (MEA) fabrication approach. Nevertheless, it bears significant challenges related to excessive swelling of the wetted membranes and catalyst layers during coating. Thermal decaling, which is currently used in proton exchange electrolysis, cannot be used with typical hydrocarbon‐based anion‐exchange membranes due to the lack of a glass transition point. In this work, a novel direct‐coating approach for MEAs for anion‐exchange membrane water electrolysis is proposed. An additional adhesive foil is used to minimize membrane swelling during the coating of the second catalyst layer. The resulting cell efficiency (1 A cm−2 at 1.8 V with ≥ 1.9 mgIr cm−2) is comparable to spray‐coated cells, while the mass transport is reduced at higher current densities (2.11 V vs 2.27 V at 2.7 A cm−2). A fully self‐casted catalyst‐coated membrane with low thickness (35 µm) achieves promising performance of 1.4 A cm−2 at 1.8 V in 0.1 m KOH and 2.0 A cm−2 in 1 m KOH. Constant current holds at 1 A cm−2 in 1 m KOH further shows a comparably low degradation rate of both spray‐ and bar‐coated cells (≈1 mV h−1) after a stabilization period.
- 13 November 2022
- Published by Wiley in Advanced Sustainable Systems
- Vol. 7 (2)
Open AccessToward Scalable Production: Catalyst‐Coated Membranes (CCMs) for Anion‐Exchange Membrane Water Electrolysis via Direct Bar Coating
Direct catalyst coating of membranes is an obvious membrane‐electrode assembly (MEA) fabrication approach. Nevertheless, it bears significant challenges related to excessive swelling of the wetted membranes and catalyst layers during coating. Thermal decaling, which is currently used in proton exchange electrolysis, cannot be used with typical hydrocarbon‐based anion‐exchange membranes due to the lack of a glass transition point. In this work, a novel direct‐coating approach for MEAs for anion‐exchange membrane water electrolysis is proposed. An additional adhesive foil is used to minimize membrane swelling during the coating of the second catalyst layer. The resulting cell efficiency (1 A cm−2 at 1.8 V with ≥ 1.9 mgIr cm−2) is comparable to spray‐coated cells, while the mass transport is reduced at higher current densities (2.11 V vs 2.27 V at 2.7 A cm−2). A fully self‐casted catalyst‐coated membrane with low thickness (35 µm) achieves promising performance of 1.4 A cm−2 at 1.8 V in 0.1 m KOH and 2.0 A cm−2 in 1 m KOH. Constant current holds at 1 A cm−2 in 1 m KOH further shows a comparably low degradation rate of both spray‐ and bar‐coated cells (≈1 mV h−1) after a stabilization period.
- Open Access
- 30 September 2022
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 3 (23) , 8460-8468
Improving the efficiency of fully hydrocarbon-based proton-exchange membrane fuel cells by ionomer content gradients in cathode catalyst layers
Recently, the cell performances of fully hydrocarbon-based fuel cells approached those of cells with perfluorinated ionomers. Most studies used a low catalyst layer ionomer content (∼10 wt%) to enable the highest performance. However, such low ionomer contents can cause a lower cell performance, especially under application-relevant, i.e. reduced humidities (≤50% relative humidity). This work systematically investigates ionomer content gradients in cathode catalyst layers based on hydrocarbon ionomer. A graded ionomer content in the catalyst layer with a higher ionomer content in the vicinity of the membrane (I/C = 0.4, 25% of total layer) and a lower ionomer content (I/C = 0.2, 75% of entire layer) near the gas diffusion layer was found to ensure sufficient proton conductivity without compromising reactant transport. In single-cell tests at hot and dry operation conditions (H2/air, 95 °C and 50% RH), the graded layer enabled both significantly improved current density at relevant cell potentials vs. a monolithic catalyst layer (496 mA cm−2 vs. 367 mA cm−2@0.7 V) and slightly increased peak performance (0.76 W cm−2 vs. 0.71 W cm−2). Under the given conditions, the performance of the graded layer is similar to that of a Nafion catalyst layer. At 80% RH, the hydrocarbon-graded catalyst layer outperforms the Nafion catalyst layer at high current densities.
- 30 September 2022
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 3 (23) , 8460-8468
Open AccessImproving the efficiency of fully hydrocarbon-based proton-exchange membrane fuel cells by ionomer content gradients in cathode catalyst layers
Recently, the cell performances of fully hydrocarbon-based fuel cells approached those of cells with perfluorinated ionomers. Most studies used a low catalyst layer ionomer content (∼10 wt%) to enable the highest performance. However, such low ionomer contents can cause a lower cell performance, especially under application-relevant, i.e. reduced humidities (≤50% relative humidity). This work systematically investigates ionomer content gradients in cathode catalyst layers based on hydrocarbon ionomer. A graded ionomer content in the catalyst layer with a higher ionomer content in the vicinity of the membrane (I/C = 0.4, 25% of total layer) and a lower ionomer content (I/C = 0.2, 75% of entire layer) near the gas diffusion layer was found to ensure sufficient proton conductivity without compromising reactant transport. In single-cell tests at hot and dry operation conditions (H2/air, 95 °C and 50% RH), the graded layer enabled both significantly improved current density at relevant cell potentials vs. a monolithic catalyst layer (496 mA cm−2 vs. 367 mA cm−2@0.7 V) and slightly increased peak performance (0.76 W cm−2 vs. 0.71 W cm−2). Under the given conditions, the performance of the graded layer is similar to that of a Nafion catalyst layer. At 80% RH, the hydrocarbon-graded catalyst layer outperforms the Nafion catalyst layer at high current densities.
- Open Access
- 26 June 2022
- Published by American Chemical Society (ACS) in ChemRxiv
Alternative and facile production pathway towards obtaining high surface area PtCo/C intermetallic catalysts for improved PEM fuel cell performance
The design of catalysts with stable and finely dispersed platinum or platinum alloy nanoparticles on the carbon support is key in controlling the performance of proton exchange membrane (PEM) fuel cells. In the present work, an intermetallic PtCo/C catalyst is synthesized via double-passivation galvanic displacement. TEM and XRD confirm a significantly narrowed particle size distribution for the catalyst particles compared to commercial benchmark catalysts (Umicore PtCo/C). Only about 10 % of the mass fraction of PtCo particles show a diameter larger than 8 nm, whereas up to > 35 % for the reference systems. This directly results in a considerable increase in electrochemically active surface area (96 m² g-1 vs. > 70 m² g-1), which confirms the more efficient usage of precious catalyst metal in the novel catalyst. Single-cell tests validates this finding by improved PEM fuel cell performance. Reducing the cathode catalyst loading from 0.4 mg cm-² to 0.25 mg cm-² resulted in a power density drop at application-relevant 0.7 V of only 4 % for the novel catalyst, compared to the 10 % and 20 % for the commercial benchmarks reference catalysts.
- 26 June 2022
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessAlternative and facile production pathway towards obtaining high surface area PtCo/C intermetallic catalysts for improved PEM fuel cell performance
The design of catalysts with stable and finely dispersed platinum or platinum alloy nanoparticles on the carbon support is key in controlling the performance of proton exchange membrane (PEM) fuel cells. In the present work, an intermetallic PtCo/C catalyst is synthesized via double-passivation galvanic displacement. TEM and XRD confirm a significantly narrowed particle size distribution for the catalyst particles compared to commercial benchmark catalysts (Umicore PtCo/C). Only about 10 % of the mass fraction of PtCo particles show a diameter larger than 8 nm, whereas up to > 35 % for the reference systems. This directly results in a considerable increase in electrochemically active surface area (96 m² g-1 vs. > 70 m² g-1), which confirms the more efficient usage of precious catalyst metal in the novel catalyst. Single-cell tests validates this finding by improved PEM fuel cell performance. Reducing the cathode catalyst loading from 0.4 mg cm-² to 0.25 mg cm-² resulted in a power density drop at application-relevant 0.7 V of only 4 % for the novel catalyst, compared to the 10 % and 20 % for the commercial benchmarks reference catalysts.