Qiao Cai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Qiao Cai has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Yongfu Li
Shanghai Jiao Tong University
9 shared publications - Yang Zhao
School of Integrated Circuits, Shanghai Jiao Tong University, Shanghai, China
7 shared publications - Xinzi Xu
Shanghai Jiao Tong University,Department of Micro/Nano Electrorics,Shanghai,China
6 shared publications - Yanxing Suo
Shanghai Jiao Tong University
5 shared publications - Guoxing Wang
Shanghai Jiao Tong University
3 shared publications - Guanghua Qian
Shanghai Jiao Tong University
2 shared publications
Latest Publications
- 21 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 19 (5) , 908-919
A 0.48$^{\circ}$ Phase Error 91.1 dB SNR Bioimpedance Measurement IC for Monitoring Cardiopulmonary Diseases
This article presents a low-power and low phase error bioimpedance (BioZ) measurement IC designed for monitoring cardiopulmonary diseases. To compensate for the phase shift introduced along the signal path by current generator (CG), electrodes and sensor analog front-end (AFE), a novel phase shift calibration logic is proposed. Utilizing this calibration logic, a single-channel in-phase demodulation-based impedance measurement scheme is developed. A noise shaping pseudo-sine wave CG with data-weighted averaging (DWA) is used to minimize modulation harmonics. Fabricated in a 0.18μm CMOS process, the chip occupies 0.73mm2 and consumes between 52.7 to 97.5μA current from a 1.8V supply. The CG achieves 74.1dB SFDR and –70dB THD at 15.5kHz with a 50μApk stimulation current. The chip achieves $2 \text{m} \Omega / \sqrt{} Hz$ input-referred impedance noise at 1Hz, 91.1dB SNR (BW=4Hz), $36 \text{k} \Omega$ input range and less than 0.48° phase error (0–90°, 1–20kHz). On-body BioZ experiments using a 4-electrode configuration demonstrate clear recordings of Impedance Cardiography (ICG) and respiration signals.
- 21 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 19 (5) , 908-919
A 0.48$^{\circ}$ Phase Error 91.1 dB SNR Bioimpedance Measurement IC for Monitoring Cardiopulmonary Diseases
This article presents a low-power and low phase error bioimpedance (BioZ) measurement IC designed for monitoring cardiopulmonary diseases. To compensate for the phase shift introduced along the signal path by current generator (CG), electrodes and sensor analog front-end (AFE), a novel phase shift calibration logic is proposed. Utilizing this calibration logic, a single-channel in-phase demodulation-based impedance measurement scheme is developed. A noise shaping pseudo-sine wave CG with data-weighted averaging (DWA) is used to minimize modulation harmonics. Fabricated in a 0.18μm CMOS process, the chip occupies 0.73mm2 and consumes between 52.7 to 97.5μA current from a 1.8V supply. The CG achieves 74.1dB SFDR and –70dB THD at 15.5kHz with a 50μApk stimulation current. The chip achieves $2 \text{m} \Omega / \sqrt{} Hz$ input-referred impedance noise at 1Hz, 91.1dB SNR (BW=4Hz), $36 \text{k} \Omega$ input range and less than 0.48° phase error (0–90°, 1–20kHz). On-body BioZ experiments using a 4-electrode configuration demonstrate clear recordings of Impedance Cardiography (ICG) and respiration signals.
- 6 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 19 (6) , 1160-1174
Artifact-Tolerant Electrophysiological Sensor Interface With 3.6V/1.8V DM/CM Input Range and 52.3mV pp /${\mu}$s Recovery Using Asynchronous Signal Folding
In the practical implementations of wearable sensors, motion artifacts with large amplitudes often cause signal chain saturation, significantly degrading biopotential signal integrity. Similarly, rapid stimulation artifacts are inevitable during closed-loop brain stimulation therapy, posing additional challenges for real-time signal acquisition. To address motion and stimulation artifacts with amplitudes reaching hundreds of mV while minimizing information loss, a sensor interface with high input range and fast artifacts recovery capability is essential. This paper presents a continuous-time track-and-zoom (CT-TAZ) technique designed to handle large artifacts events without saturation. The proposed system achieves a 3.6V/1.8V differential-mode/common-mode full-scale input range. Fabricated in a 180nm CMOS process, the prototype chip occupies an area of 0.694mm2 and consumes 12/32.6/51.6μW for recordings without/with single-end/ with differential rail-to-rail artifacts. The system demonstrates an average artifacts recovery time of 65.3 μs under 3.6V stimulation artifacts, achieving an average artifacts recovery speed of 52.3mVpp/μs, which is 2.25× larger input range and 3× faster recovery compared to the state-of-the-art.
- 6 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 19 (6) , 1160-1174
Artifact-Tolerant Electrophysiological Sensor Interface With 3.6V/1.8V DM/CM Input Range and 52.3mV pp /${\mu}$s Recovery Using Asynchronous Signal Folding
In the practical implementations of wearable sensors, motion artifacts with large amplitudes often cause signal chain saturation, significantly degrading biopotential signal integrity. Similarly, rapid stimulation artifacts are inevitable during closed-loop brain stimulation therapy, posing additional challenges for real-time signal acquisition. To address motion and stimulation artifacts with amplitudes reaching hundreds of mV while minimizing information loss, a sensor interface with high input range and fast artifacts recovery capability is essential. This paper presents a continuous-time track-and-zoom (CT-TAZ) technique designed to handle large artifacts events without saturation. The proposed system achieves a 3.6V/1.8V differential-mode/common-mode full-scale input range. Fabricated in a 180nm CMOS process, the prototype chip occupies an area of 0.694mm2 and consumes 12/32.6/51.6μW for recordings without/with single-end/ with differential rail-to-rail artifacts. The system demonstrates an average artifacts recovery time of 65.3 μs under 3.6V stimulation artifacts, achieving an average artifacts recovery speed of 52.3mVpp/μs, which is 2.25× larger input range and 3× faster recovery compared to the state-of-the-art.
- 19 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
A Lightweight CNN Spike Sorting Method Enhanced by Scattering Convolution Network
Spike sorting is an effective approach for analysis of neuron activities. With the increasing number of recording channels, online spike sorting is seen as a promising solution to relax the wireless transmission burden. Deep learning based methods provide superior spike sorting accuracy but require intensive computation offsetting the efficient transmission. To cut down the computation cost, a scattering convolution network (SCN) is proposed to extract features via wavelet scattering transform, then a lightweight convolutional neural network (CNN) is capable of sorting the spikes accurately. Experiment results demonstrate that the proposed SCN-CNN method achieves over 92% computation reduction and maintains a high classification accuracy of up to 99.97%, showing huge potential for online spike sorting on large-scale neural probes.
- 19 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
A Lightweight CNN Spike Sorting Method Enhanced by Scattering Convolution Network
Spike sorting is an effective approach for analysis of neuron activities. With the increasing number of recording channels, online spike sorting is seen as a promising solution to relax the wireless transmission burden. Deep learning based methods provide superior spike sorting accuracy but require intensive computation offsetting the efficient transmission. To cut down the computation cost, a scattering convolution network (SCN) is proposed to extract features via wavelet scattering transform, then a lightweight convolutional neural network (CNN) is capable of sorting the spikes accurately. Experiment results demonstrate that the proposed SCN-CNN method achieves over 92% computation reduction and maintains a high classification accuracy of up to 99.97%, showing huge potential for online spike sorting on large-scale neural probes.
- 19 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
An Adaptive BPSK Modulated Wireless Inductive Link for Implantable Devices
Binary phase shift-keying (BPSK) modulation shows great potential for wireless data and power transmission via single inductive link. Conventional BPSK modulation suffers from the inefficiency of wasting modulation cycles on bits that remain unchanged. An adaptive BPSK (A-BPSK) encoding-decoding mechanism is proposed in this paper to encode the unchanged bits with merely one carrier cycle, greatly enhancing the transmission capacity. Applying on a Class-E inductive link, an A-BPSK wireless transmission chipset is implemented in a 0.18μm BCD process. At a 13.56MHz carrier, post-layout simulation shows a minimum and maximum data rates of 3.87Mbps and 13.56Mbps, respectively. Statistically, the average data rate can be 6.02Mbps showing 2X over speed up.
- 19 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
An Adaptive BPSK Modulated Wireless Inductive Link for Implantable Devices
Binary phase shift-keying (BPSK) modulation shows great potential for wireless data and power transmission via single inductive link. Conventional BPSK modulation suffers from the inefficiency of wasting modulation cycles on bits that remain unchanged. An adaptive BPSK (A-BPSK) encoding-decoding mechanism is proposed in this paper to encode the unchanged bits with merely one carrier cycle, greatly enhancing the transmission capacity. Applying on a Class-E inductive link, an A-BPSK wireless transmission chipset is implemented in a 0.18μm BCD process. At a 13.56MHz carrier, post-layout simulation shows a minimum and maximum data rates of 3.87Mbps and 13.56Mbps, respectively. Statistically, the average data rate can be 6.02Mbps showing 2X over speed up.
- 19 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 36, 1-5
A Peak Detection Algorithm for Multimodal Physiological Signals Based on U-Net
Fiducial points detection serves as the cornerstone of physiological signal processing. Conventional multimodal biomedical sensors require the deployment of diverse or reconfigurable algorithms to handle different types of signals. However, these approaches can be complex and costly in terms of hardware, or require more processing time. To address these challenges, a unified adaptive thresholding method enhanced with a signal synthesizer is proposed to processing multimodal physiological signals to get R-peak, systolic peak and spike, respectively. The proposed approach is evaluated on MIT-BIH, MIMIC and Quiroga databases, achieving precision of 99.03%, 99.38%, 98.81% and recall rate of 99.34%, 99.63%, 98.14% for R-peak, systolic-peak and spike-potential, respectively. These results demonstrate a promising energy-efficient solution for multimodal real-time monitoring.
- 19 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 36, 1-5
A Peak Detection Algorithm for Multimodal Physiological Signals Based on U-Net
Fiducial points detection serves as the cornerstone of physiological signal processing. Conventional multimodal biomedical sensors require the deployment of diverse or reconfigurable algorithms to handle different types of signals. However, these approaches can be complex and costly in terms of hardware, or require more processing time. To address these challenges, a unified adaptive thresholding method enhanced with a signal synthesizer is proposed to processing multimodal physiological signals to get R-peak, systolic peak and spike, respectively. The proposed approach is evaluated on MIT-BIH, MIMIC and Quiroga databases, achieving precision of 99.03%, 99.38%, 98.81% and recall rate of 99.34%, 99.63%, 98.14% for R-peak, systolic-peak and spike-potential, respectively. These results demonstrate a promising energy-efficient solution for multimodal real-time monitoring.
- 28 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 16 (5) , 793-806
A 2.66 µW Clinician-Like Cardiac Arrhythmia Watchdog Based on P-QRS-T for Wearable Applications
Wearable electrocardiogram (ECG) device is an effective tool for managing cardiovascular diseases. This paper presents a low power clinician-like cardiac arrhythmia watchdog (CAW) for wearable ECG devices. The CAW is based on a novel P-QRS-T detection algorithm that makes use of clinical features to identify abnormalities. Implemented in 0.18μm CMOS process, the CAW consumes 2.66µW for 80bpm heart rate at 1.2V supply with an area of 0.578mm2. Verified on QT database, the average sensitivity /positive predictivity for P-wave, QRS complex and T-wave are over 93.39%/88.55%, 99.69%/99.48%, and 97.13%/93.18% respectively, across over 190000 beats. It shows over 99.8% arrhythmia detection accuracy for 43 subjects evaluated on MIT-BIH database.
- 28 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 16 (5) , 793-806
A 2.66 µW Clinician-Like Cardiac Arrhythmia Watchdog Based on P-QRS-T for Wearable Applications
Wearable electrocardiogram (ECG) device is an effective tool for managing cardiovascular diseases. This paper presents a low power clinician-like cardiac arrhythmia watchdog (CAW) for wearable ECG devices. The CAW is based on a novel P-QRS-T detection algorithm that makes use of clinical features to identify abnormalities. Implemented in 0.18μm CMOS process, the CAW consumes 2.66µW for 80bpm heart rate at 1.2V supply with an area of 0.578mm2. Verified on QT database, the average sensitivity /positive predictivity for P-wave, QRS complex and T-wave are over 93.39%/88.55%, 99.69%/99.48%, and 97.13%/93.18% respectively, across over 190000 beats. It shows over 99.8% arrhythmia detection accuracy for 43 subjects evaluated on MIT-BIH database.
- 22 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 68 (9) , 3123-3127
A 1.3 μW Event-Driven ANN Core for Cardiac Arrhythmia Classification in Wearable Sensors
An event-driven system generates samples only when a predefined event is triggered, thus the power consumption tracks the input activities leading to significant savings in power for wearable sensors. In this brief, we presented an event-driven artificial neural network (ANN) core for cardiac arrhythmia classifier (CAC). The proposed data alignment mechanism allows seamless cooperation between the ANN CAC core and the event-driven clockless analog front-end. Measurement results show that the ANN CAC core consumes merely 1.3μW dynamic power at heart rate of 75bpm with a clock frequency of 250kHz a 1.5V supply voltage. Fabricated in 0.18μm, the core occupies 0.75mm 2 with minimum 1.8 μJ/classification, achieving average classification accuracy of 98% for all 5 types of heart beats as defined in the AAMI.
- 22 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 68 (9) , 3123-3127
A 1.3 μW Event-Driven ANN Core for Cardiac Arrhythmia Classification in Wearable Sensors
An event-driven system generates samples only when a predefined event is triggered, thus the power consumption tracks the input activities leading to significant savings in power for wearable sensors. In this brief, we presented an event-driven artificial neural network (ANN) core for cardiac arrhythmia classifier (CAC). The proposed data alignment mechanism allows seamless cooperation between the ANN CAC core and the event-driven clockless analog front-end. Measurement results show that the ANN CAC core consumes merely 1.3μW dynamic power at heart rate of 75bpm with a clock frequency of 250kHz a 1.5V supply voltage. Fabricated in 0.18μm, the core occupies 0.75mm 2 with minimum 1.8 μJ/classification, achieving average classification accuracy of 98% for all 5 types of heart beats as defined in the AAMI.
- Open Access
- 3 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 79904-79910
An Ultra-Low-Voltage Level Shifter With Embedded Re-Configurable Logic and Time-Borrowing Latch Technique
The increasing number of voltage domains along with the size of the data bus requires an exponential increase in the number level shifter (LS) circuits for signal interfacing, creating an exploding in silicon area and power consumption. Higher area-efficiency can be attained by further improving the integration density of the LS circuit. In this paper, we present a multi-function ultra-low-voltage LS with re-configurable logic with embedded time-borrowing latch. The proposed circuit is implemented on CMOS 45nm technology. It is capable of converting the input voltage of 0.3 V to an output voltage of 1.8 V with an input frequency of 1 MHz. The proposed architecture has achieved a superior area efficiency with reduced transistors number of 2.4× and reduced power delay product (PDP) of 4.65× compared with its discrete logic block level implementation when the input voltage, output voltage, and the input frequency are 0.3 V, 1.8 V, and 1 MHz, respectively. The average propagation delay and power consumption are 52.7 ns and 34.6 nW, respectively.
- 3 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 79904-79910
Open AccessAn Ultra-Low-Voltage Level Shifter With Embedded Re-Configurable Logic and Time-Borrowing Latch Technique
The increasing number of voltage domains along with the size of the data bus requires an exponential increase in the number level shifter (LS) circuits for signal interfacing, creating an exploding in silicon area and power consumption. Higher area-efficiency can be attained by further improving the integration density of the LS circuit. In this paper, we present a multi-function ultra-low-voltage LS with re-configurable logic with embedded time-borrowing latch. The proposed circuit is implemented on CMOS 45nm technology. It is capable of converting the input voltage of 0.3 V to an output voltage of 1.8 V with an input frequency of 1 MHz. The proposed architecture has achieved a superior area efficiency with reduced transistors number of 2.4× and reduced power delay product (PDP) of 4.65× compared with its discrete logic block level implementation when the input voltage, output voltage, and the input frequency are 0.3 V, 1.8 V, and 1 MHz, respectively. The average propagation delay and power consumption are 52.7 ns and 34.6 nW, respectively.