Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yueh-Tsung Shieh has a total of 25 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Modulated Quasi-Continuous-Wave Laser Module for Free-Space Optics

    by Chun-Hao Chen, Chun-Hsiung Lin, Hao-Chung Kuo, Yu-Heng Hong, Ching-Yao Liu, Kai-En Lin, Yueh-Tsung Shieh, Shyr-Long Jeng, Edward-Yi Chang, Wei-Hua Chieng

    A quasi-continuous-wave (QCW) laser module based on a half-bridge structure is proposed for the low-voltage silicon photonics application, which forms a continuous-wave (CW) laser output when it equally distributes the heat dissipation into all lasers. Such a QCW laser module is modulated into a CW laser source for the chip-to-chip or board-to-board communication. The source current is alternatively diverted to the high-side and the low-side lasers by turning the corresponding gallium nitride high-electron-mobility transistor (GaN HEMT) on and off. The current redirection modulates multiple QCW laser outputs into a CW laser output; however, an undesirable laser downtime is produced during the transition time of the current redirection. Although for the 10 Gbps data rate transmission, a short laser downtime period may be scheduled for the time to perform either the laser steering task of the free-space optics (FSO) operation or the data pause for the fan-out delay, which is still preferred to be minimized for higher data rate transmission. The power efficiency and the laser downtime are functions of the parameters of the laser diodes, switch parasitic capacitances, input voltage, and the inductor. According to the mathematical derivation of the circuit response, the circuit design rules and the switching control strategy are provided to achieve high efficiency and low laser downtime. In the experiment, we implemented a laser module to achieve an FSO specification with a laser downtime of less than 3 ns, total harmonic distortion (THD) less than 10%, power efficiency greater than 60% and laser power higher than 1 W.

  • Open Access

    Efficiency-Based CLLC Bidirectional DC-DC Converter Using Copolar Switching

    by Yueh-Tsung Hsieh, Chun-Hao Chen, Wen-Yuh Shieh, Chi-Chun Haung, Wei-Hua Chieng, Edward Yi Chang

    This paper introduces a novel switching method called copolar switching, designed to maintain high power efficiency in CLLC bidirectional chargers across different modes of operation. The proposed method sets the switching frequency close to the resonance of the LC tank within the CLLC circuit, ensuring efficient power conversion in both the forward (charging) and reverse (discharging) modes. Using Fourier series analysis and circuit theory, the necessary duty cycle for achieving the target efficiency is derived and applied to the full bridge on the high-voltage side in reverse mode. Copolar switching ensures that the entire CLLC circuit operates at a single resonant frequency, addressing the conventional issue of unbalanced efficiency between forward and reverse power conversions. A prototype circuit was designed for power conversion between 400 V and 48 V. Experimental results demonstrate 1 kW power conversion with 97% efficiency in forward mode and 800 W conversion with the same efficiency in reverse mode. Additionally, the copolar switching method shows potential for applications requiring voltage output adjustments, such as converting between 400 V and 50 V.


  • Open Access

    Design of GaN HEMT Buck Converter for BCM Operation

    by Yueh-Tsung Hsieh, Chun-Hao Chen, Tsung-Lin Chen, Wei-Hua Chieng, Edward-Yi Chang

    Power density and power efficiency are crucial for the design of high-performance computing servers. Buck converters exist due to their simplicity, but achieving a solution that combines high efficiency and high power density remains an ongoing research area in buck converter design. High-frequency switching, which reduces inductor size in buck converters, is a common method for achieving high power density; however, high-frequency switching introduces higher switching losses, hence the frequent use of GaN HEMTs, which have low switching losses. To achieve both high efficiency and high power density, this study proposes a compact buck converter design that pairs a D-type GaN HEMT with a low-voltage PMOS, termed a P-cascode GaN HEMT. We analyze different current switching modes and find that boundary conduction mode (BCM) can minimize inductor size while maintaining high power efficiency. This paper explores the theoretical basis of BCM and the P-cascode GaN HEMT, derives the operating conditions of BCM, estimates power efficiency, and proposes a high-power density buck converter solution. Simulation and experimental results show that the proposed design achieves 95% power efficiency in applications from 12 V to 3.3 V, while reducing the inductor size by a factor of 10 compared to continuous conduction mode (CCM) designs.


  • Open Access

    Copolar Synchronous Switching Method for BLDC Motor Control in EV Application

    by Yueh-Tsung Hsieh, Gang-Ting Liou, Shyr-Long Jeng, Wei-Hua Chieng, Jih-Sheng Lai, Edward-Yi Chang

    This paper proposes a new PWM switching method, called copolar switching, for synchronous rectification in brushless DC motors (BLDC). This method-integrates the benefits of both unipolar and bipolar switching, addressing the efficiency trade-off commonly observed in low-resistance BLDC drives. Unipolar switching is known to reduce current ripple and switching losses at low speeds, while bipolar switching enhances efficiency during high-speed operation due to faster recovery of freewheeling current. However, most existing methods statically adopt one scheme, leading to suboptimal performance across variable-speed conditions. The proposed copolar switching method combines unipolar switching at zero-speed for ripple-free conduction, and switches to bipolar mode at higher speeds to enable rapid energy feedback to the source. Therefore, it can be used in electric vehicles (EV) applications to increase the average power efficiency. The EV simulation in this paper identified there could be a 5% efficiency improvement.


  • Coprime Reconstruction of Super-Nyquist Periodic Signal and Sampling Moiré Effect

    by Hsien-Chung Tang, Yueh-Tsung Hsieh, Rohit Roy, Shyr-Long Jeng, Wei-Hua Chieng

    Sampling moiré effect is well-known in signal processing. When a continuous periodic signal $x(t)$ is sampled using a sampling rate $f_{s}$ that does not respect the Nyquist condition, and the signal-frequency $f_{x}$ folds over and gives a special sequence in the sampled signal. The coprime reconstruction is made possible when the periodic signal frequency $f_{x}$ and the sampling frequency $f_{s}$ satisfy $f_{s}/f_{x}=N/M$ with integer $M$, $N$, where $N/M$ is a reduced fraction. This article shows how to rearrange the N sample data into one entire period of the signal using the M periods of the signal. The reconstruction is equivalent to the decryption of the sample data using the method referred to the mathematic operator “multiplicative inverse modulo.” In the implementation to verify the coprime reconstruction, we used a commodity DSP board with 4.2 MHz sampling rate to reconstruct the 13.56 MHz signal acquired from the ADC circuit. The signal reconstruction result is comparable to the sampling result for the same signal sampled at 475 MHz sampling rate. The other simulation on the 234 kHz signal under 1 MHz sampling rate yields a very detail information on the signal with a finding that the multiplicative inverse modulo may also be used as the encryption of signal for network security use.


  • Open Access

    Power Receiving Unit for High-Power Resonant Wireless Power Transfer

    by Ching-Yao Liu, Hsien-Chung Tang, Yueh-Tsung Shieh, Chih-Chiang Wu, Wei-Hua Chieng, Edward-Yi Chang, Daisuke Ueda

    A new power receiving unit (PRU) is proposed in this paper for resonant wireless power transfer (WPT), which is characterized by the capability of attracting high power from the power transmitting unit (PTU). The resonant WPT is designed for delivering the electrical power to the PRU attached on an electrical vehicle (EV) chassis 50 cm away from a PTU installed on the ground. The proposed PRU uses only the passive elements such as inductors, diodes, and capacitors, which need no initial power from the EV. It is then applicable for charging a battery to several hundred volts for even a first-time charging battery. For a resonant WPT at a switching frequency of 4 MHz, the proposed PRU behaves as a negative impedance converter (NIC) itself in the subharmonics of 4 MHz. The NIC effect plus the subharmonic oscillation causes an instability current charging the battery connected to the PRU. In this paper, we simulated the PRU and performed the experiment. The experiment demonstrated a battery charging of 150 W from 50 cm away using three D-mode GaN HEMT transistors via the instability current ramp. The power transfer efficiency (PTE) improved as the power delivered to the load (PDL) increased. The peak PTE was 65% in the present findings. The simulation analysis showed that the circuit allowed itself be used to much higher power transfer when it is implemented with more GaN HEMT transistors connected in parallel. The theoretical derivation of the PRU circuit is also used to support both the experimental and simulation results.


  • Open Access

    Power Receiving Unit for High Power Resonant Wireless Power Transfer

    by Ching-Yao Liu, Hsien-Chung Tang, Yueh-Tsung Shieh, Chih-Chiang Wu, Wei-Hua Chieng, Edward-Yi Chang, Daisuke Ueda

    A new power receiving unit (PRU) is proposed in this paper for the resonant wireless power transfer (WPT), which is characterized by the capability of attracting high power from the power transmitting unit (PTU). The resonant WPT is designed for delivering the electrical power to the PRU attached on an electrical vehicle (EV) chassis 50cm away from a PTU installed on the ground. The proposed PRU uses only the passive elements such as inductors, diodes and the capacitors, which needs no initial power from the EV. It is then applicable for charging a battery to several hundred volts for even a first-time charging battery. At a switching frequency of the resonant WPT in the experiment being 4MHz, the proposed PRU behaves itself as a negative impedance converter (NIC) in the subharmonics of 4MHz. The NIC effect plus the subharmonic oscillation causes an instability current charging the battery connected to the PRU. In this paper, we simulated the PRU and performed the experiment. The experiment demonstrates a battery charging of 150W from 50cm away using three D-mode GaN HEMT transistors via the instability current ramp. The power transfer efficiency (PTE) improved as the power delivered to load (PDL) goes higher. The best power transfer efficiency (PTE) is 65% in the present findings. The simulation analysis shows that the circuit allows itself be used to much higher power transfer when it is implemented with more GaN HEMT transistors connected in parallel. The theoretical derivation of the PRU circuit is also used to support both the experimental and simulation results.


  • Open Access

    A Turn-Ratio-Changing Half-Bridge CLLC DC–DC Bidirectional Battery Charger Using a GaN HEMT

    by Yueh-Tsung Shieh, Chih-Chiang Wu, Shyr-Long Jeng, Ching-Yao Liu, Shiang-Yu Hsieh, Chi-Chun Haung, Wen-Yuh Shieh, Wei-Hua Chieng, Edward-Yi Chang

    This paper presents a 250 kHz bidirectional battery charger circuit using a GaN HEMT. The charger is subjected to a high-/low-side constant voltage at 200 V/20 V. The charger circuit is a hybrid of the LLC and flyback circuit topologies. Both the power output analysis and efficiency control of this circuit are simplified when the magnetization current is minimized using the low-resistance GaN HEMT. The switching frequency is controlled to match the series resonance in a way that is analogous to conventional LLC circuit controls, while the duty ratio that determines the power output and the dead time, which determines the zero voltage switching, is controlled in an analogous manner to the flyback circuit control. The charging and discharging modes were altered by applying a double-throw relay that changes the transformer turn ratio, which is different from conventional LLC designs using the switching frequency adjustment. A nominal turn ratio with Np = 35 and Ns = 3.5 for a 200 V/20 V converter can only produce an internal series resonance with no current flowing in any charging direction. The proposed circuit using a transformer with multiple windings (Np = 35, Ns,F = 4, and Ns,R = 3) was fabricated to deliver 125 W output power from the power grid battery to the vehicle battery in the forward (charging) mode and 90 W in the reverse (discharging) mode. The conversion efficiency was calculated to be as high as 97% in the forward mode and 95% in the reverse mode. The high conversion efficiency is due to the characteristics of the GaN HEMT, including low resistive and switching losses. The equations derived in this paper associate these losses with the series resonant frequency and power conversion rate, which highlight the advantages of using a GaN HEMT in this CLLC design.


  • Open Access

    Resonant Mechanism for a Long-Distance Wireless Power Transfer Using Class E PA and GaN HEMT

    by Ching-Yao Liu, Chih-Chiang Wu, Li-Chuan Tang, Yueh-Tsung Shieh, Wei-Hua Chieng, Edward-Yi Chang

    This paper presents a study on long-distance wireless power transfer (WPT), which formulates the voltage gain in terms of the coupling coefficient between the power transmitting unit (PTU) and the power receiving unit (PRU) coils. It is proposed that maximum power transfer efficiency (PTE) can be reached when maximum voltage gain is achieved under a matching condition between the coil quality factor and the coupling coefficient. In order to achieve maximum power delivered to load (PDL), we need to elevate the input voltage as high as the high breakdown-voltage of gallium nitride (GaN) high-electron mobility transistors (HEMT) along with class E amplifier circuit topology. In order to promote voltage gain, knowledge of the coupling coefficient between two coils including the factors of the coil diameter, wire diameter, coil turns, and the coil resistance are derived. It was observed that a lower coil resistance leads to a reduced parallel quality, which facilitates long-distance wireless power transfer. Experimental results support the findings that the maximum PTE occurred at the maximum voltage gain existing at a specific distance matches the coupling coefficient between coils. A maximum power point tracking (MPPT) method is also developed to achieve maximum PDL. At a distance of 35 cm, experiments with more than 100 W successfully receive a PTE of 57% at the PRU when the received voltage reached 1.4 kV. This is used to verify the concepts and analysis that are proposed in this paper.


  • Open Access

    Lithium Battery Model and Its Application to Parallel Charging

    by Yueh-Tsung Shieh, Chih-Chiang Wu, Ching-Yao Liu, Wei-Hua Chieng, Yu-Sheng Su, Shyr-Long Jeng, Edward-Yi Chang

    A new SOC (State-Of-Charge)–VOC (Voltage-of-Open-Circuit) mathematical model was proposed in this paper, which is particularly useful in parallel lithium battery modeling. When the battery strings are charged in parallel connection, the batteries can be deemed as capacitors with different capacitances, and the one with larger capacitance always obtains the higher current. According to this mathematical model, the parallel battery charging with different peak capacitances can result in different voltage slew rates on different battery strings during the constant current control. Different parallel battery strings are charged with different currents, of which the battery string under higher current can induce higher power loss and higher temperature. The conventional solution can use this model to switch the constant current charging into the constant voltage charging with the correct timing to avoid overcurrent charging. Other battery pack protection methods including current sense resistor, resettable thermal cutoff device, or resettable fuse can also use this mathematical model to improve the protection. In the experiments, three kinds of batteries including LiFePO4 battery, EV Type-1 battery, and ternary battery were examined. The experiments showed good consistency with the simulation results derived from the mathematical model.