Leonid Ya. Karachinsky
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Leonid Ya. Karachinsky has a total of 213 co-authors. Here are the top co-authors by number of shared publications:
- Andrey V. Babichev
Ioffe Institute
39 shared publications - Innokenty I. Novikov
ITMO University
39 shared publications - Anton Yu. Egorov
ITMO University
30 shared publications - Andrey G. Gladyshev
ITMO University
25 shared publications - Mikhail A. Bobrov
Ioffe Institute, Saint Petersburg, Russia
25 shared publications - Sergey A. Blokhin
Ioffe Institute
20 shared publications
Latest Publications
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 32 (6: Special) , 1702317
High-Speed and Energy-Efficient Long-Wavelength VCSELs for Optical Interconnects: A Review
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 32 (6: Special) , 1702317
High-Speed and Energy-Efficient Long-Wavelength VCSELs for Optical Interconnects: A Review
- Open Access
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 32 (6: Special) , 1701910
Energy-Efficient Long Distance 1550 nm VCSEL-Based Fiber Transmitters
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 32 (6: Special) , 1701910
Open AccessEnergy-Efficient Long Distance 1550 nm VCSEL-Based Fiber Transmitters
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 32 (6: Special) , 1-8
Quantum-Dot Surface-Emitting Lasers: Micropillar Cavities Grown by Molecular-Beam Epitaxy
Micropillar cavity lasers demonstrate operation up to 255 K. At this temperature, the lasing threshold and Q-factor, extracted at lasing threshold for a 4 μm diameter pillar are about 2 mW and 16800. For pillar lasers, the concept of which is based on an optical aperture, continuous-wave lasing is realized at room temperature (300 K). For a 15 μm diameter pillar with an aperture of 4 μm, single-mode lasing at 960 nm is demonstrated with a threshold power of about 12 mW and a Q-factor at threshold of 13000.
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 32 (6: Special) , 1-8
Quantum-Dot Surface-Emitting Lasers: Micropillar Cavities Grown by Molecular-Beam Epitaxy
Micropillar cavity lasers demonstrate operation up to 255 K. At this temperature, the lasing threshold and Q-factor, extracted at lasing threshold for a 4 μm diameter pillar are about 2 mW and 16800. For pillar lasers, the concept of which is based on an optical aperture, continuous-wave lasing is realized at room temperature (300 K). For a 15 μm diameter pillar with an aperture of 4 μm, single-mode lasing at 960 nm is demonstrated with a threshold power of about 12 mW and a Q-factor at threshold of 13000.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 16 (10) , 2327-2333
Characterization of Heat Dissipation in Quantum Cascade Lasers: Experiment, Analytics, and Applications
Heat removal from an active region of a quantum cascade laser (QCL) is a key challenge for achieving continuous-wave lasing and ensuring reliable operation. A key issue in addressing this challenge is the efficiency of all stages of post-growth processing of heterostructures and QCL chip assembly. This paper presents a model of heat propagation across a QCL chip, demonstrating the nonuniformity of this process, characterized by an effective diffusivity constant, which measures the efficiency of heat removal from the QCL’s active region. It is demonstrated that the diffusivity constant can be experimentally determined by measuring the nonlinear chirp of the Fabry-Perot modes’ frequency. Experimental studies of a series of QCL samples fabricated from the same heterostructure but with differences in the post-growth process demonstrated that the proposed model and experimental chirp measurement technique enable the identification of the most optimal approaches to post-growth processing for efficient heat removal from the active region.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 16 (10) , 2327-2333
Characterization of Heat Dissipation in Quantum Cascade Lasers: Experiment, Analytics, and Applications
Heat removal from an active region of a quantum cascade laser (QCL) is a key challenge for achieving continuous-wave lasing and ensuring reliable operation. A key issue in addressing this challenge is the efficiency of all stages of post-growth processing of heterostructures and QCL chip assembly. This paper presents a model of heat propagation across a QCL chip, demonstrating the nonuniformity of this process, characterized by an effective diffusivity constant, which measures the efficiency of heat removal from the QCL’s active region. It is demonstrated that the diffusivity constant can be experimentally determined by measuring the nonlinear chirp of the Fabry-Perot modes’ frequency. Experimental studies of a series of QCL samples fabricated from the same heterostructure but with differences in the post-growth process demonstrated that the proposed model and experimental chirp measurement technique enable the identification of the most optimal approaches to post-growth processing for efficient heat removal from the active region.
- 15 June 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (24)
Room-temperature, continuous wave lasing in planar microcavities with quantum dots
High-quality planar cavities with low-absorption mirrors based on Al0.2Ga0.8As/Al0.9Ga0.1As layers demonstrate continuous wave lasing at a wavelength of 956 nm. At 300 K, the threshold power density and the quality-factor at the threshold are (4.2 ± 0.3) kW/cm2 and (6800 ± 220). Increasing the pump level above two thresholds results in an enlargement in the quality-factor to at least 19 000. Efficient lateral heat dissipation in planar semiconductor microcavities is confirmed by the low mode-energy shift of approximately 400 μeV at two lasing thresholds.
- 15 June 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (24)
Room-temperature, continuous wave lasing in planar microcavities with quantum dots
High-quality planar cavities with low-absorption mirrors based on Al0.2Ga0.8As/Al0.9Ga0.1As layers demonstrate continuous wave lasing at a wavelength of 956 nm. At 300 K, the threshold power density and the quality-factor at the threshold are (4.2 ± 0.3) kW/cm2 and (6800 ± 220). Increasing the pump level above two thresholds results in an enlargement in the quality-factor to at least 19 000. Efficient lateral heat dissipation in planar semiconductor microcavities is confirmed by the low mode-energy shift of approximately 400 μeV at two lasing thresholds.
- 2 February 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (5)
Advanced micropillar cavities: Room-temperature operation of microlasers
High-quality micropillar cavities were grown using molecular-beam epitaxy. Stable continuous-wave lasing at room temperature was demonstrated for microlasers with semiconductor and hybrid output mirrors. At 300 K, single-mode lasing was demonstrated for micropillars with a diameter of 5 μm at a wavelength of 960 nm, with a minimum lasing threshold of ∼1.2 mW and the quality-factor at threshold exceeding 8000.
- 2 February 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (5)
Advanced micropillar cavities: Room-temperature operation of microlasers
High-quality micropillar cavities were grown using molecular-beam epitaxy. Stable continuous-wave lasing at room temperature was demonstrated for microlasers with semiconductor and hybrid output mirrors. At 300 K, single-mode lasing was demonstrated for micropillars with a diameter of 5 μm at a wavelength of 960 nm, with a minimum lasing threshold of ∼1.2 mW and the quality-factor at threshold exceeding 8000.
- 23 December 2025
- Published by ITMO University in Scientific and Technical Journal of Information Technologies, Mechanics and Optics
- Vol. 25 (6)
Influence of the growth rate of a highly strained InGaAs quantum well on the photoluminescence of a heterostructures grown on GaAs substrate
Epitaxy of highly strained InGaAs quantum wells with a mole fraction of indium exceeding 35 % is a technologically challenging task. The structural quality of these elastically strained epitaxial layers greatly affects the photoluminescence efficiency of quantum wells. Therefore, in order to achieve high structural quality, optimization of the epitaxial growth parameters is required, one of which is the growth rate of the epitaxial layer. Heterostructures containing the In x Ga 1–x As (0.37 ≤ x < 0.41) quantum well were produced on GaAs substrates by molecular beam epitaxy with different growth rates of InGaAs ranging from 0.24 to 3.3 Å/s. The actual thickness and composition of the quantum well were determined by X-ray diffractometry, as well as the structural quality of the heterostructures was investigated. The photoluminescence spectra of the manufactured heterostructures were measured at temperatures of 20 K and 300 K at different optical pumping powers. Based on the dependence of photoluminescence intensity on pumping power, recombination currents were calculated and the time of non-radiative recombination in the studied structures was estimated. The InAs content in the quantum wells of the manufactured heterostructures ranged from 37.0 % to 40.6 %. Based on analysis of X-ray rocking curves, deterioration of structural quality at low deposition rate of 0.24 Å/s was observed. The photoluminescence spectroscopy measurements showed a significantly higher photoluminescence intensity of quantum wells at moderate growth rates of InGaAs (0.9–2.5 Å/s) compared to other samples. The calculated values for the non-radiative recombination lifetime of quantum wells produced at these moderate growth rates were in the order of 10 –6 s at 20 K and 10 –9 s at 300 K. At higher or lower growth rates, the values of the non-radiative recombination lifetime decreased. The results obtained demonstrate the achievement of the best structural quality for highly strained InGaAs layers produced at 0.9–2.5 Å/s growth rate. These results can be used to optimize the parameters of epitaxial growth processes for highly strained quantum wells based on InGaAs, for fabricating monolithic vertical-cavity surface-emitting lasers, based on GaAs substrate, operating in the 1200–1300 nm spectral range.
- 23 December 2025
- Published by ITMO University in Scientific and Technical Journal of Information Technologies, Mechanics and Optics
- Vol. 25 (6)
Influence of the growth rate of a highly strained InGaAs quantum well on the photoluminescence of a heterostructures grown on GaAs substrate
Epitaxy of highly strained InGaAs quantum wells with a mole fraction of indium exceeding 35 % is a technologically challenging task. The structural quality of these elastically strained epitaxial layers greatly affects the photoluminescence efficiency of quantum wells. Therefore, in order to achieve high structural quality, optimization of the epitaxial growth parameters is required, one of which is the growth rate of the epitaxial layer. Heterostructures containing the In x Ga 1–x As (0.37 ≤ x < 0.41) quantum well were produced on GaAs substrates by molecular beam epitaxy with different growth rates of InGaAs ranging from 0.24 to 3.3 Å/s. The actual thickness and composition of the quantum well were determined by X-ray diffractometry, as well as the structural quality of the heterostructures was investigated. The photoluminescence spectra of the manufactured heterostructures were measured at temperatures of 20 K and 300 K at different optical pumping powers. Based on the dependence of photoluminescence intensity on pumping power, recombination currents were calculated and the time of non-radiative recombination in the studied structures was estimated. The InAs content in the quantum wells of the manufactured heterostructures ranged from 37.0 % to 40.6 %. Based on analysis of X-ray rocking curves, deterioration of structural quality at low deposition rate of 0.24 Å/s was observed. The photoluminescence spectroscopy measurements showed a significantly higher photoluminescence intensity of quantum wells at moderate growth rates of InGaAs (0.9–2.5 Å/s) compared to other samples. The calculated values for the non-radiative recombination lifetime of quantum wells produced at these moderate growth rates were in the order of 10 –6 s at 20 K and 10 –9 s at 300 K. At higher or lower growth rates, the values of the non-radiative recombination lifetime decreased. The results obtained demonstrate the achievement of the best structural quality for highly strained InGaAs layers produced at 0.9–2.5 Å/s growth rate. These results can be used to optimize the parameters of epitaxial growth processes for highly strained quantum wells based on InGaAs, for fabricating monolithic vertical-cavity surface-emitting lasers, based on GaAs substrate, operating in the 1200–1300 nm spectral range.
- 1 December 2025
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 92 (12) , 751-755
Maximum wall-plug efficiency of 1300-nm single-frequency vertical-cavity surface-emitting lasers
Subject of study. Single-frequency 1300-nm vertical-cavity surface-emitting lasers (VCSELs) fabricated using a combination of wafer fusion and molecular beam epitaxy (MBE) are studied. Aim of study. The study aims to determine the buried tunnel junction (BTJ) mesa diameter of single-frequency 1300-nm VCSELs that provides maximum wall-plug efficiency (WPE) over a temperature range of 20–100°C. Method. VCSEL heterostructures were fabricated by the wafer fusion of two distributed Bragg reflector (DBR) heterostructures and an active-region heterostructure with a BTJ. Semiconductor heterostructures, including GaAs/AlGaAs DBRs on GaAs substrates and an InGaAs/InAlAs/InP active-region heterostructure with a BTJ on an InP substrate, were grown via MBE. Main results. The maximum WPE of the fabricated single-frequency 1300-nm VCSELs is achieved for devices with a BTJ mesa diameter of 6 µm and varies from 30% at 20°C to 7% at 100°C. Practical significance. Devices with maximum WPE are required to minimize heat generation in laser arrays based on single-frequency long-wavelength VCSELs. Analysis of the obtained results indicates that VCSELs with a BTJ diameter of 6 µm are optimal for this application.
- 1 December 2025
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 92 (12) , 751-755
Maximum wall-plug efficiency of 1300-nm single-frequency vertical-cavity surface-emitting lasers
Subject of study. Single-frequency 1300-nm vertical-cavity surface-emitting lasers (VCSELs) fabricated using a combination of wafer fusion and molecular beam epitaxy (MBE) are studied. Aim of study. The study aims to determine the buried tunnel junction (BTJ) mesa diameter of single-frequency 1300-nm VCSELs that provides maximum wall-plug efficiency (WPE) over a temperature range of 20–100°C. Method. VCSEL heterostructures were fabricated by the wafer fusion of two distributed Bragg reflector (DBR) heterostructures and an active-region heterostructure with a BTJ. Semiconductor heterostructures, including GaAs/AlGaAs DBRs on GaAs substrates and an InGaAs/InAlAs/InP active-region heterostructure with a BTJ on an InP substrate, were grown via MBE. Main results. The maximum WPE of the fabricated single-frequency 1300-nm VCSELs is achieved for devices with a BTJ mesa diameter of 6 µm and varies from 30% at 20°C to 7% at 100°C. Practical significance. Devices with maximum WPE are required to minimize heat generation in laser arrays based on single-frequency long-wavelength VCSELs. Analysis of the obtained results indicates that VCSELs with a BTJ diameter of 6 µm are optimal for this application.
- Open Access
- 3 July 2025
- Published by IOP Publishing in Journal of Physics: Photonics
- Vol. 7 (3) , 032001
Long-wavelength VCSELs with buried tunnel junction: design optimization
The review is focused on reporting about design optimizations of the long-wavelength (LW) vertical-cavity surface-emitting laser (VCSELs) with an aperture formed by regrown (buried) tunnel junctions, pioneered by Amann et al from the Technical University of Munich and Vertilas GmbH. Ultra-low-cost solutions for the above 10 Gbps data rates were realized for a short-cavity (SC) design (with one semiconductor and one dielectric mirror) intended for the 1300–1550 nm range. A modified SC design was also used for 2D VCSEL arrays applied as a short wave infrared illuminator. Cost-effective ultra-high modulation rates (larger than 40 Gbps) were realized for the ultra SC design (with hybrid and dielectric mirrors), suitable for telecommunication and datacom. Since the current tuning range of LW VCSELs is significantly larger than that of distributed feedback edge-emitting lasers, Amann et al developed SC InP-based VCSELs design dedicated for gas detection (in the 1.8–2.3 μm range). Tunable micro-electromechanical systems VCSELs have also been employed, as well as GaSb-based VCSELs. The latter ones are presently limited in use due to their low modal gain in the VCSEL geometry. The design of 1300–1550 nm wafer-fused (WF) VCSELs grown by metal-organic chemical vapor deposition was primarily developed by Kapon et al from the Swiss Federal Institute of Technology/BeamExpress SA. This approach allowed full-wafer processing and met Telcordia compliant qualifications. The design of WF VCSELs grown by industrial molecular-beam epitaxy has been implemented by the team of the present authors and demonstrated promising applications for intra-data-center connections. Trumpf Photonic Components announced the mass production of InP-based VCSELs above 1300 nm. Sony Semiconductor Solutions Corporation has been demonstrated 1380 nm range WF VCSELs. InP-based VCSELs design from Corning Inc. can also be adopted for under organic light-emitting diode display applications or as a short wave infrared illuminator.
- 3 July 2025
- Published by IOP Publishing in Journal of Physics: Photonics
- Vol. 7 (3) , 032001
Open AccessLong-wavelength VCSELs with buried tunnel junction: design optimization
The review is focused on reporting about design optimizations of the long-wavelength (LW) vertical-cavity surface-emitting laser (VCSELs) with an aperture formed by regrown (buried) tunnel junctions, pioneered by Amann et al from the Technical University of Munich and Vertilas GmbH. Ultra-low-cost solutions for the above 10 Gbps data rates were realized for a short-cavity (SC) design (with one semiconductor and one dielectric mirror) intended for the 1300–1550 nm range. A modified SC design was also used for 2D VCSEL arrays applied as a short wave infrared illuminator. Cost-effective ultra-high modulation rates (larger than 40 Gbps) were realized for the ultra SC design (with hybrid and dielectric mirrors), suitable for telecommunication and datacom. Since the current tuning range of LW VCSELs is significantly larger than that of distributed feedback edge-emitting lasers, Amann et al developed SC InP-based VCSELs design dedicated for gas detection (in the 1.8–2.3 μm range). Tunable micro-electromechanical systems VCSELs have also been employed, as well as GaSb-based VCSELs. The latter ones are presently limited in use due to their low modal gain in the VCSEL geometry. The design of 1300–1550 nm wafer-fused (WF) VCSELs grown by metal-organic chemical vapor deposition was primarily developed by Kapon et al from the Swiss Federal Institute of Technology/BeamExpress SA. This approach allowed full-wafer processing and met Telcordia compliant qualifications. The design of WF VCSELs grown by industrial molecular-beam epitaxy has been implemented by the team of the present authors and demonstrated promising applications for intra-data-center connections. Trumpf Photonic Components announced the mass production of InP-based VCSELs above 1300 nm. Sony Semiconductor Solutions Corporation has been demonstrated 1380 nm range WF VCSELs. InP-based VCSELs design from Corning Inc. can also be adopted for under organic light-emitting diode display applications or as a short wave infrared illuminator.
- 19 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 61 (2) , 1-9
Gain and Threshold Improvements of 1300 nm Lasers Based on InGaAs/InAlGaAs Superlattice Active Regions
A detailed experimental analysis of the impact of active region design on the performance of 1300 nm lasers based on InGaAs/InAlGaAs superlattices is presented. Three different types of superlattice active regions and waveguide layer compositions were grown. Using a superlattice allows to downshift the energy position of the miniband, as compared to thin InGaAs quantum wells, having the same composition, being beneficial for high-temperature operation. Very low internal loss (~6 cm-1), low transparency current density of ~500 A/cm2, together with 46 cm-1 modal gain and 53 % internal efficiency were observed for broad-area lasers with an active region based on a highly strained In0.74Ga0.26As/In0.53Al0.25Ga0.22As superlattice. Characteristic temperatures T0 and T1 were improved up to 76 K and 100 K, respectively. These data suggest that such superlattices have also the potential to much improve VCSEL properties at this wavelength.
- 19 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 61 (2) , 1-9
Gain and Threshold Improvements of 1300 nm Lasers Based on InGaAs/InAlGaAs Superlattice Active Regions
A detailed experimental analysis of the impact of active region design on the performance of 1300 nm lasers based on InGaAs/InAlGaAs superlattices is presented. Three different types of superlattice active regions and waveguide layer compositions were grown. Using a superlattice allows to downshift the energy position of the miniband, as compared to thin InGaAs quantum wells, having the same composition, being beneficial for high-temperature operation. Very low internal loss (~6 cm-1), low transparency current density of ~500 A/cm2, together with 46 cm-1 modal gain and 53 % internal efficiency were observed for broad-area lasers with an active region based on a highly strained In0.74Ga0.26As/In0.53Al0.25Ga0.22As superlattice. Characteristic temperatures T0 and T1 were improved up to 76 K and 100 K, respectively. These data suggest that such superlattices have also the potential to much improve VCSEL properties at this wavelength.