Mikhail A. Bobrov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mikhail A. Bobrov has a total of 201 co-authors. Here are the top co-authors by number of shared publications:
- Alexander Kuzmenkov
Физико-технический институт им. А.Ф. Иоффе РАН, Санкт-Петербург, Россия
27 shared publications - Leonid Ya. Karachinsky
ITMO University
25 shared publications - N. A. Maleev
Ioffe Institute, St. Petersburg, Russia
24 shared publications - Innokenty I. Novikov
ITMO University
23 shared publications - Andrey V. Babichev
Ioffe Institute
22 shared publications С.а. Блохин
Физико-технический институт им. А.Ф. Иоффе РАН, Санкт-Петербург, Россия
18 shared publications
Latest Publications
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 32 (6: Special) , 1-8
Quantum-Dot Surface-Emitting Lasers: Micropillar Cavities Grown by Molecular-Beam Epitaxy
Micropillar cavity lasers demonstrate operation up to 255 K. At this temperature, the lasing threshold and Q-factor, extracted at lasing threshold for a 4 μm diameter pillar are about 2 mW and 16800. For pillar lasers, the concept of which is based on an optical aperture, continuous-wave lasing is realized at room temperature (300 K). For a 15 μm diameter pillar with an aperture of 4 μm, single-mode lasing at 960 nm is demonstrated with a threshold power of about 12 mW and a Q-factor at threshold of 13000.
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 32 (6: Special) , 1-8
Quantum-Dot Surface-Emitting Lasers: Micropillar Cavities Grown by Molecular-Beam Epitaxy
Micropillar cavity lasers demonstrate operation up to 255 K. At this temperature, the lasing threshold and Q-factor, extracted at lasing threshold for a 4 μm diameter pillar are about 2 mW and 16800. For pillar lasers, the concept of which is based on an optical aperture, continuous-wave lasing is realized at room temperature (300 K). For a 15 μm diameter pillar with an aperture of 4 μm, single-mode lasing at 960 nm is demonstrated with a threshold power of about 12 mW and a Q-factor at threshold of 13000.
- 15 June 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (24)
Room-temperature, continuous wave lasing in planar microcavities with quantum dots
High-quality planar cavities with low-absorption mirrors based on Al0.2Ga0.8As/Al0.9Ga0.1As layers demonstrate continuous wave lasing at a wavelength of 956 nm. At 300 K, the threshold power density and the quality-factor at the threshold are (4.2 ± 0.3) kW/cm2 and (6800 ± 220). Increasing the pump level above two thresholds results in an enlargement in the quality-factor to at least 19 000. Efficient lateral heat dissipation in planar semiconductor microcavities is confirmed by the low mode-energy shift of approximately 400 μeV at two lasing thresholds.
- 15 June 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (24)
Room-temperature, continuous wave lasing in planar microcavities with quantum dots
High-quality planar cavities with low-absorption mirrors based on Al0.2Ga0.8As/Al0.9Ga0.1As layers demonstrate continuous wave lasing at a wavelength of 956 nm. At 300 K, the threshold power density and the quality-factor at the threshold are (4.2 ± 0.3) kW/cm2 and (6800 ± 220). Increasing the pump level above two thresholds results in an enlargement in the quality-factor to at least 19 000. Efficient lateral heat dissipation in planar semiconductor microcavities is confirmed by the low mode-energy shift of approximately 400 μeV at two lasing thresholds.
- 2 February 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (5)
Advanced micropillar cavities: Room-temperature operation of microlasers
High-quality micropillar cavities were grown using molecular-beam epitaxy. Stable continuous-wave lasing at room temperature was demonstrated for microlasers with semiconductor and hybrid output mirrors. At 300 K, single-mode lasing was demonstrated for micropillars with a diameter of 5 μm at a wavelength of 960 nm, with a minimum lasing threshold of ∼1.2 mW and the quality-factor at threshold exceeding 8000.
- 2 February 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (5)
Advanced micropillar cavities: Room-temperature operation of microlasers
High-quality micropillar cavities were grown using molecular-beam epitaxy. Stable continuous-wave lasing at room temperature was demonstrated for microlasers with semiconductor and hybrid output mirrors. At 300 K, single-mode lasing was demonstrated for micropillars with a diameter of 5 μm at a wavelength of 960 nm, with a minimum lasing threshold of ∼1.2 mW and the quality-factor at threshold exceeding 8000.
- 1 December 2024
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 91 (12) , 789-795
Analysis of the α-factor in 1.55-µm vertical-cavity surface-emitting lasers based on InGaAs/InAlGaAs quantum wells
Subject of study. Semiconductor-based vertical-cavity surface-emitting lasers (VCSELs) fabricated using a combined wafer-fusion and molecular beam epitaxy technique are studied. Aim of study. The aim was to determine the linewidth enhancement factor (α-factor) of single-mode VCSELs operating in the 1.55-µm spectral range. These VCSELs were based on strained InGaAs/InGaAlAs quantum wells and fabricated using a combined wafer-fusion and molecular beam epitaxy method. Method. The α-factor was estimated by direct measurements of the laser emission linewidth with a scanning Fabry–Pérot interferometer, small-signal frequency analysis, and analysis of the shifts in the resonant wavelength in the spontaneous emission spectra with changes in the charge carrier concentration. Main results. An increase in the inverse population factor or charge carrier lifetime leads to a decrease in the α-factor for VCSELs fabricated using the combined wafer-fusion and molecular beam epitaxy technique. For the studied lasers, the α-factor values lie in the range of 3 to 4.5, depending on the photon lifetime in the cavity. Practical significance. The obtained results make it possible to correlate the photon lifetime in the cavity to the α-factor of VCSELs operating in the 1.55-µm spectral range. This correlation is crucial for designing gas sensors and high-speed optical transceivers based on such lasers.
- 1 December 2024
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 91 (12) , 789-795
Analysis of the α-factor in 1.55-µm vertical-cavity surface-emitting lasers based on InGaAs/InAlGaAs quantum wells
Subject of study. Semiconductor-based vertical-cavity surface-emitting lasers (VCSELs) fabricated using a combined wafer-fusion and molecular beam epitaxy technique are studied. Aim of study. The aim was to determine the linewidth enhancement factor (α-factor) of single-mode VCSELs operating in the 1.55-µm spectral range. These VCSELs were based on strained InGaAs/InGaAlAs quantum wells and fabricated using a combined wafer-fusion and molecular beam epitaxy method. Method. The α-factor was estimated by direct measurements of the laser emission linewidth with a scanning Fabry–Pérot interferometer, small-signal frequency analysis, and analysis of the shifts in the resonant wavelength in the spontaneous emission spectra with changes in the charge carrier concentration. Main results. An increase in the inverse population factor or charge carrier lifetime leads to a decrease in the α-factor for VCSELs fabricated using the combined wafer-fusion and molecular beam epitaxy technique. For the studied lasers, the α-factor values lie in the range of 3 to 4.5, depending on the photon lifetime in the cavity. Practical significance. The obtained results make it possible to correlate the photon lifetime in the cavity to the α-factor of VCSELs operating in the 1.55-µm spectral range. This correlation is crucial for designing gas sensors and high-speed optical transceivers based on such lasers.
- 1 December 2024
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 91 (12) , 796-802
Energy efficiency of 1.55-µm vertical-cavity surface-emitting lasers with an active region based on strained InGaAs/InAlGaAs quantum wells
Subject of study. This study examines vertical-cavity surface-emitting lasers (VCSELs) operating at 1.55 µm, based on strained InGaAs/InAlGaAs quantum wells. These VCSELs were fabricated using wafer-fusion (WF) technology to bond distributed Bragg reflector heterostructures with an optical cavity grown by molecular beam epitaxy (MBE). Aim of study. The aim was to assess the energy efficiency of information transmission using 1.55-µm VCSELs, fabricated using a combination of WF and MBE techniques, across a wide range of bit rates from 5 Gbits/s to 30 Gbits/s. Method. The method involved recording eye diagrams at various bit rates for VCSELs under large-signal amplitude modulation and estimating the effective modulation bandwidth and dynamic energy efficiency of the lasers via small-signal analysis. Main results. The results showed that minimum energy consumption (0.83 pJ/bit) was achieved at a bit rate of 20 Gbits/s, which is consistent with theoretical predictions. Further increasing the operating current to support higher bit rates resulted in a sharp increase in energy consumption, as the modulation bandwidth increased more slowly than did the energy input. At the maximum tested bit rate of 30 Gbits/s, where an open eye diagram was still observed, the energy efficiency decreased to 1.2 pJ/bit. Practical significance. These findings are significant for the development of energy-efficient, high-speed fiber-optic transceivers based on 1.55-µm VCSELs.
- 1 December 2024
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 91 (12) , 796-802
Energy efficiency of 1.55-µm vertical-cavity surface-emitting lasers with an active region based on strained InGaAs/InAlGaAs quantum wells
Subject of study. This study examines vertical-cavity surface-emitting lasers (VCSELs) operating at 1.55 µm, based on strained InGaAs/InAlGaAs quantum wells. These VCSELs were fabricated using wafer-fusion (WF) technology to bond distributed Bragg reflector heterostructures with an optical cavity grown by molecular beam epitaxy (MBE). Aim of study. The aim was to assess the energy efficiency of information transmission using 1.55-µm VCSELs, fabricated using a combination of WF and MBE techniques, across a wide range of bit rates from 5 Gbits/s to 30 Gbits/s. Method. The method involved recording eye diagrams at various bit rates for VCSELs under large-signal amplitude modulation and estimating the effective modulation bandwidth and dynamic energy efficiency of the lasers via small-signal analysis. Main results. The results showed that minimum energy consumption (0.83 pJ/bit) was achieved at a bit rate of 20 Gbits/s, which is consistent with theoretical predictions. Further increasing the operating current to support higher bit rates resulted in a sharp increase in energy consumption, as the modulation bandwidth increased more slowly than did the energy input. At the maximum tested bit rate of 30 Gbits/s, where an open eye diagram was still observed, the energy efficiency decreased to 1.2 pJ/bit. Practical significance. These findings are significant for the development of energy-efficient, high-speed fiber-optic transceivers based on 1.55-µm VCSELs.
- 21 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 31 (2: Pwr. an) , 1-8
Low-Threshold Surface-Emitting Whispering-Gallery Mode Microlasers
We report on microlasers based on high-quality micropillars with whispering-gallery modes lasing. The use of low-absorbing Al0.2Ga0.8As/Al0.9Ga0.1As distributed Bragg reflectors and smooth pillar sidewalls enables whispering-gallery modes lasing by excitation and collection of emission in the pillar axis direction. Simultaneous whispering gallery modes lasing (comb-like structure) is observed in the wavelength range of 930–970 nm for 3–7 μm pillar diameters. Increasing the temperature to 130 K leads to single-mode lasing for 5 μm pillars with a cold cavity quality-factor of about 8000 and an estimated threshold excitation power of 240 μW. Lasing in the thermoelectrical cooling range (up to 170 K) has been demonstrated.
- 21 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 31 (2: Pwr. an) , 1-8
Low-Threshold Surface-Emitting Whispering-Gallery Mode Microlasers
We report on microlasers based on high-quality micropillars with whispering-gallery modes lasing. The use of low-absorbing Al0.2Ga0.8As/Al0.9Ga0.1As distributed Bragg reflectors and smooth pillar sidewalls enables whispering-gallery modes lasing by excitation and collection of emission in the pillar axis direction. Simultaneous whispering gallery modes lasing (comb-like structure) is observed in the wavelength range of 930–970 nm for 3–7 μm pillar diameters. Increasing the temperature to 130 K leads to single-mode lasing for 5 μm pillars with a cold cavity quality-factor of about 8000 and an estimated threshold excitation power of 240 μW. Lasing in the thermoelectrical cooling range (up to 170 K) has been demonstrated.
- 8 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 31 (5: Quantum) , 1-8
Lasing of Quantum-Dot Micropillar Lasers Under Elevated Temperatures
A comprehensive numerical modelling of microcavity parameters for micropillar lasers with optical pumping was presented. The structure with a hybrid dielectric-semiconductor top mirror has a significantly higher calculated quality-factor (∼65000 for 5 μm pillar) due to better vertical mode confinement. The minimum laser threshold (∼370 μW for 5 μm pillar) coincided with a temperature of 130 K, which is close to zero gain to cavity detuning. Lasing up to 220 K was demonstrated with a laser threshold of about 2.2 mW.
- 8 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 31 (5: Quantum) , 1-8
Lasing of Quantum-Dot Micropillar Lasers Under Elevated Temperatures
A comprehensive numerical modelling of microcavity parameters for micropillar lasers with optical pumping was presented. The structure with a hybrid dielectric-semiconductor top mirror has a significantly higher calculated quality-factor (∼65000 for 5 μm pillar) due to better vertical mode confinement. The minimum laser threshold (∼370 μW for 5 μm pillar) coincided with a temperature of 130 K, which is close to zero gain to cavity detuning. Lasing up to 220 K was demonstrated with a laser threshold of about 2.2 mW.
- 1 December 2023
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 49 (S3) , S184-S189
Investigation of the Noise Characteristics of Vertical-Cavity Surface-Emitting Laser with a Rhomboidal Oxide Current Aperture for Use in a Cs-Based Compact Atomic Magnetometer
—The possibility of using vertical-emitting lasers with intracavity contacts (IC-VCSEL) and a rhomboidal oxide current aperture for creating a non-zero magnetic field optically pumped atomic magnetometers (OPM) with a 133Cs vapor cell for magnetoencephalographic (MEG) systems were demonstrated. Relative intensity noise (RIN) and polarization resolved RIN of the IC-VCSEL in the 895 nm range with different mirror losses (linewidth) in the frequency range from 1Hz to 100 kHz were experimentally investigated. Lasers with low mirror loss (narrow linewidth) have polarization resolved RIN comparable to amplitude noise. For IC-VCSEL with an output optical power of 0.8 mW and a linewidth of 55 MHz, the noise level measured is 148 dB/Hz in 1 Hz bandwidth at 40 kHz frequency. The ultimate sensitivity of OPM based on two-beam MZ-scheme with studied VCSELs was estimated as ~11 fT/\(\sqrt {{\text{Hz}}} \).- 1 December 2023
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 49 (S3) , S184-S189
Investigation of the Noise Characteristics of Vertical-Cavity Surface-Emitting Laser with a Rhomboidal Oxide Current Aperture for Use in a Cs-Based Compact Atomic Magnetometer
—The possibility of using vertical-emitting lasers with intracavity contacts (IC-VCSEL) and a rhomboidal oxide current aperture for creating a non-zero magnetic field optically pumped atomic magnetometers (OPM) with a 133Cs vapor cell for magnetoencephalographic (MEG) systems were demonstrated. Relative intensity noise (RIN) and polarization resolved RIN of the IC-VCSEL in the 895 nm range with different mirror losses (linewidth) in the frequency range from 1Hz to 100 kHz were experimentally investigated. Lasers with low mirror loss (narrow linewidth) have polarization resolved RIN comparable to amplitude noise. For IC-VCSEL with an output optical power of 0.8 mW and a linewidth of 55 MHz, the noise level measured is 148 dB/Hz in 1 Hz bandwidth at 40 kHz frequency. The ultimate sensitivity of OPM based on two-beam MZ-scheme with studied VCSELs was estimated as ~11 fT/\(\sqrt {{\text{Hz}}} \).- Open Access
- 8 May 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (9) , 1572
Towards Bright Single-Photon Emission in Elliptical Micropillars
In recent years, single-photon sources (SPSs) based on the emission of a single semiconductor quantum dot (QD) have been actively developed. While the purity and indistinguishability of single photons are already close to ideal values, the high brightness of SPSs remains a challenge. The widely used resonant excitation with cross-polarization filtering usually leads to at least a two-fold reduction in the single-photon counts rate, since single-photon emission is usually unpolarized, or its polarization state is close to that of the exciting laser. One of the solutions is the use of polarization-selective microcavities, which allows one to redirect most of the QD emission to a specific polarization determined by the optical mode of the microcavity. In the present work, elliptical micropillars with distributed Bragg reflectors are investigated theoretically and experimentally as a promising design of such polarization-selective microcavities. The impact of ellipticity, ellipse area and verticality of the side walls on the splitting of the optical fundamental mode is investigated. The study of the near-field pattern allows us to detect the presence of higher-order optical modes, which are classified theoretically. The possibility of obtaining strongly polarized single-photon QD radiation associated with the short-wavelength fundamental cavity mode is shown.
- 8 May 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (9) , 1572
Open AccessTowards Bright Single-Photon Emission in Elliptical Micropillars
In recent years, single-photon sources (SPSs) based on the emission of a single semiconductor quantum dot (QD) have been actively developed. While the purity and indistinguishability of single photons are already close to ideal values, the high brightness of SPSs remains a challenge. The widely used resonant excitation with cross-polarization filtering usually leads to at least a two-fold reduction in the single-photon counts rate, since single-photon emission is usually unpolarized, or its polarization state is close to that of the exciting laser. One of the solutions is the use of polarization-selective microcavities, which allows one to redirect most of the QD emission to a specific polarization determined by the optical mode of the microcavity. In the present work, elliptical micropillars with distributed Bragg reflectors are investigated theoretically and experimentally as a promising design of such polarization-selective microcavities. The impact of ellipticity, ellipse area and verticality of the side walls on the splitting of the optical fundamental mode is investigated. The study of the near-field pattern allows us to detect the presence of higher-order optical modes, which are classified theoretically. The possibility of obtaining strongly polarized single-photon QD radiation associated with the short-wavelength fundamental cavity mode is shown.
- 1 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 35 (6) , 297-300
Single-Mode High-Speed 1550 nm Wafer Fused VCSELs for Narrow WDM Systems
High power single-mode wafer fused 1550 nm VCSELs with an active region based on InGaAs quantum wells are fabricated. An InP-based optical cavity and two AlGaAs/GaAs distributed Bragg reflector heterostructures were grown by molecular-beam epita oy. The current and optical confinements are provided by a lateral-structured buried tunnel junction with $\sim ~6~\mu \text{m}$ diameter and etching depth of ~ 20 nm. The VCSELs demonstrate ~ 3.4 mW single-mode continuous-wave output optical power and a threshold current about 2 mA at 20°C. The output optical power exceeds 1 mW at 70°C. A −3dB modulation bandwidth > 13 GHz is obtained at 20°C. Non-return-to-zero data transmission under back-to-back condition of ~ 37 Gbps is shown.
- 1 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 35 (6) , 297-300
Single-Mode High-Speed 1550 nm Wafer Fused VCSELs for Narrow WDM Systems
High power single-mode wafer fused 1550 nm VCSELs with an active region based on InGaAs quantum wells are fabricated. An InP-based optical cavity and two AlGaAs/GaAs distributed Bragg reflector heterostructures were grown by molecular-beam epita oy. The current and optical confinements are provided by a lateral-structured buried tunnel junction with $\sim ~6~\mu \text{m}$ diameter and etching depth of ~ 20 nm. The VCSELs demonstrate ~ 3.4 mW single-mode continuous-wave output optical power and a threshold current about 2 mA at 20°C. The output optical power exceeds 1 mW at 70°C. A −3dB modulation bandwidth > 13 GHz is obtained at 20°C. Non-return-to-zero data transmission under back-to-back condition of ~ 37 Gbps is shown.