Jie Ning
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jie Ning has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
Lin-Jie Zhang
11 shared publications- Lin-Jie Zhang
State Key Laboratory for Mechanical Behavior of Materials Xi'an Jiaotong University Xi'an China
10 shared publications Suck-Joo Na
State Key Laboratory for Mechanical Behavior of Materials, Xi'an Jiaotong University, Xi'an, China
6 shared publicationsChao Feng
3 shared publicationsJian Long
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an, China
2 shared publicationsLi-Ang Chen
2 shared publications
Latest Publications
- Open Access
- 17 September 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 45, 1743-1752
A novel method for measuring micro-regional residual stress by nanoindentation
- 17 September 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 45, 1743-1752
Open AccessA novel method for measuring micro-regional residual stress by nanoindentation
- 8 September 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (10) , 10743-10759
Microstructure and mechanical properties of CrMo low-alloy steel parts manufactured by submerged arc additive manufacturing technology
- 8 September 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (10) , 10743-10759
Microstructure and mechanical properties of CrMo low-alloy steel parts manufactured by submerged arc additive manufacturing technology
- 7 August 2026
- Published by Springer Nature in Heat and Mass Transfer
- Vol. 62 (8) , 115
Droplet transfer behavior and its regulation mechanism of high-pressure laser welding with filler wire of Ti6Al4V titanium Alloy
- 7 August 2026
- Published by Springer Nature in Heat and Mass Transfer
- Vol. 62 (8) , 115
Droplet transfer behavior and its regulation mechanism of high-pressure laser welding with filler wire of Ti6Al4V titanium Alloy
- Open Access
- 22 June 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 43, 3730-3739
Effect of Ti–N composite alloying on the microstructure and mechanical properties of laser-welded pure molybdenum joints
- 22 June 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 43, 3730-3739
Open AccessEffect of Ti–N composite alloying on the microstructure and mechanical properties of laser-welded pure molybdenum joints
- Open Access
- 16 April 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of Nanoscale ZrC Addition on the Microstructure and Mechanical Properties of Laser-Welded Molybdenum Alloy Joints
Molybdenum (Mo) alloys are critical for next-generation nuclear applications, yet their engineering utility is hindered by the "weldability-brittleness" paradox caused by grain coarsening and interstitial oxygen segregation. This study proposes an active grain-boundary engineering (GBE) strategy by incorporating nanoscale ZrC into laser-welded 0.45wt.% La2O3-strengthened Mo joints. Thermodynamic analysis and experimental results demonstrate that ZrC acts as a potent chemical buffer, scavenging detrimental oxygen to form stable ZrO2 and reducing grain-boundary MoO2 concentrations from 0.4% to 0.1%. Simultaneously, the nanoscale ZrC and in-situ ZrO2 particles facilitate heterogeneous nucleation and Zener pinning, yielding a 17.2% reduction in fusion zone (FZ) grain size. Consequently, the ZrC-modified joints achieved a peak room-temperature tensile strength of 449.7 MPa—a 12-fold increase over unmodified specimens (33.8 MPa)—while retaining 75.7% of the base metal strength at 1100°C. Fractographic analysis reveals a fundamental transition from catastrophic intergranular decohesion to transgranular cleavage, signifying a significant restoration of grain boundary cohesive strength. This study provides a robust technical framework for enhancing the joint integrity of refractory metals via targeted nanophase intervention.
- 16 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of Nanoscale ZrC Addition on the Microstructure and Mechanical Properties of Laser-Welded Molybdenum Alloy Joints
Molybdenum (Mo) alloys are critical for next-generation nuclear applications, yet their engineering utility is hindered by the "weldability-brittleness" paradox caused by grain coarsening and interstitial oxygen segregation. This study proposes an active grain-boundary engineering (GBE) strategy by incorporating nanoscale ZrC into laser-welded 0.45wt.% La2O3-strengthened Mo joints. Thermodynamic analysis and experimental results demonstrate that ZrC acts as a potent chemical buffer, scavenging detrimental oxygen to form stable ZrO2 and reducing grain-boundary MoO2 concentrations from 0.4% to 0.1%. Simultaneously, the nanoscale ZrC and in-situ ZrO2 particles facilitate heterogeneous nucleation and Zener pinning, yielding a 17.2% reduction in fusion zone (FZ) grain size. Consequently, the ZrC-modified joints achieved a peak room-temperature tensile strength of 449.7 MPa—a 12-fold increase over unmodified specimens (33.8 MPa)—while retaining 75.7% of the base metal strength at 1100°C. Fractographic analysis reveals a fundamental transition from catastrophic intergranular decohesion to transgranular cleavage, signifying a significant restoration of grain boundary cohesive strength. This study provides a robust technical framework for enhancing the joint integrity of refractory metals via targeted nanophase intervention.
- Open Access
- 28 December 2025
- Published by Elsevier in Materials & Design
- Vol. 262
Improving the mechanical properties of laser-welded joints of GH4169/Nb521 dissimilar materials by using a wedge-shaped Ni interlayer
- 28 December 2025
- Published by Elsevier in Materials & Design
- Vol. 262
Open AccessImproving the mechanical properties of laser-welded joints of GH4169/Nb521 dissimilar materials by using a wedge-shaped Ni interlayer
- 1 June 2025
- Published by SAGE Publications in 3D Printing and Additive Manufacturing
- Vol. 12 (3) , 199-212
Effects of Cu Addition on the Microstructures and Properties of WC-12Co Cemented Carbides Additively Manufactured by Laser Powder-Bed Fusion
The preparation of WC-Co cemented carbides by laser-based additive manufacturing (AM) is challenging, as the resulting products are often plagued by crack and pore defects. In this study, Cu-doped WC-12Co cemented carbides were successfully prepared by laser powder-bed fusion (LPBF). The effects of LPBF parameters and Cu doping on the defects, microstructures, and properties of the WC-12Co cemented carbides were analyzed. It was found that the laser scanning speed had a significant effect on the density of the AM specimen, and that the doping of Cu reduced cracks. A slow scanning speed and small amounts of Cu dopant were found to be conducive to the manufacturing of highly dense WC-12Co-xCu AM specimens. The microstructure of LPBF-prepared WC-12Co-xCu cemented carbides contained alternating coarse- and fine-grained regions. Cu doping reduced the size of the W2C phase, caused the W1−xC phase to disappear, significantly reduced grain sizes, and increased the number of low-angle grain boundaries. Cu doping also reduced microhardness; the microhardness of the WC-12Co-3Cu specimen that was prepared using a laser scanning speed of 500 mm/s was 25.45% lower than that of WC-12Co. However, compressive strength was significantly increased by Cu doping; the compressive strength of the WC-12Co-3C specimen was 36.20% higher than that of WC-12Co. The wetting angle initially increased (up to a peak of 154° with 2 wt.% Cu) and then decreased with increasing Cu content. The maximum wetting angle was ∼5.7 times that of the undoped AM specimen.
- 1 June 2025
- Published by SAGE Publications in 3D Printing and Additive Manufacturing
- Vol. 12 (3) , 199-212
Effects of Cu Addition on the Microstructures and Properties of WC-12Co Cemented Carbides Additively Manufactured by Laser Powder-Bed Fusion
The preparation of WC-Co cemented carbides by laser-based additive manufacturing (AM) is challenging, as the resulting products are often plagued by crack and pore defects. In this study, Cu-doped WC-12Co cemented carbides were successfully prepared by laser powder-bed fusion (LPBF). The effects of LPBF parameters and Cu doping on the defects, microstructures, and properties of the WC-12Co cemented carbides were analyzed. It was found that the laser scanning speed had a significant effect on the density of the AM specimen, and that the doping of Cu reduced cracks. A slow scanning speed and small amounts of Cu dopant were found to be conducive to the manufacturing of highly dense WC-12Co-xCu AM specimens. The microstructure of LPBF-prepared WC-12Co-xCu cemented carbides contained alternating coarse- and fine-grained regions. Cu doping reduced the size of the W2C phase, caused the W1−xC phase to disappear, significantly reduced grain sizes, and increased the number of low-angle grain boundaries. Cu doping also reduced microhardness; the microhardness of the WC-12Co-3Cu specimen that was prepared using a laser scanning speed of 500 mm/s was 25.45% lower than that of WC-12Co. However, compressive strength was significantly increased by Cu doping; the compressive strength of the WC-12Co-3C specimen was 36.20% higher than that of WC-12Co. The wetting angle initially increased (up to a peak of 154° with 2 wt.% Cu) and then decreased with increasing Cu content. The maximum wetting angle was ∼5.7 times that of the undoped AM specimen.
- Open Access
- 28 April 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 36, 6316-6329
Adding Ta-based interlayer improve the performance of GH3128-Nb521 dissimilar material laser butt welded joints
- 28 April 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 36, 6316-6329
Open AccessAdding Ta-based interlayer improve the performance of GH3128-Nb521 dissimilar material laser butt welded joints
- Open Access
- 25 April 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 36, 7135-7147
Effects of laser beam offsets on the microstructures and properties of Ta10W/Nb521 dissimilar joints
- 25 April 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 36, 7135-7147
Open AccessEffects of laser beam offsets on the microstructures and properties of Ta10W/Nb521 dissimilar joints