Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Michał Młotek has a total of 38 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Influence of Different Frequency Power Generators on Plasma Temperatures in the Ammonia Decomposition Process: OES-Based Temperature Profiling in a Gliding Arc

    by Michalina Perron, Tim Gehring, Mateusz Wiosna, Wojciech Gajewski, Michał Młotek

    A gliding arc plasma reactor operated with highly concentrated ammonia (90 vol % NH3 in N2) was investigated using spatially resolved optical emission spectroscopy, electrical diagnostics, and gas chromatography. Fitting the N2 second positive system (310–360 nm) yielded rotational and vibrational temperature profiles along the arc for 50 Hz and Bipolar HV high-frequency (25–35 kHz) excitation. Results indicate local thermal equilibrium near ignition and a transition to nonequilibrium along the arc, which is a typical characteristic of a gliding arc. Bipolar HV kHz excitation produced higher vibrational temperatures, enhanced N2+ emission downstream, and substantially increased reaction rates localized in the discharge channel. It demonstrates improved energy concentration and higher ammonia conversion compared to 50 Hz, and promising potential for energy-efficient hydrogen recovery from ammonia.

  • Open Access

    Toluene Decomposition in Plasma–Catalytic Systems with Nickel Catalysts on CaO-Al2O3 Carrier

    by Joanna Woroszył-Wojno, Michał Młotek, Bogdan Ulejczyk, Krzysztof Krawczyk

    The decomposition of toluene as a tar imitator in a gas composition similar to the gas after biomass pyrolysis was studied in a plasma–catalytic system. Nickel catalysts and the plasma from gliding arc discharge under atmospheric pressure were used. The effect of the catalyst bed, discharge power, initial toluene, and hydrogen concentration on C7H8 decomposition, calorific value, and unit energy consumption were studied. The gas flow rate was 1000 NL/h, while the inlet gas composition (molar ratio) was CO (0.13), CO2 (0.15), H2 (0.28–0.38), and N2 (0.34–0.44). The study was conducted using an initial toluene concentration in the range of 2000–4500 ppm and a discharge power of 1500–2000 W. In plasma–catalytic systems, the following catalysts were compared: NiO/Al2O3, NiO/(CaO-Al2O3), and Ni/(CaO-Al2O3). The decomposition of toluene increased with its initial concentration. An increase in hydrogen concentration resulted in higher activity of the Ni/(CaO-Al2O3) catalysts. The gas composition did not change by more than 10% during the process. Trace amounts of C2 hydrocarbons were observed. The conversion of C7H8 was up to 85% when NiO/(CaO-Al2O3) was used. The products of the toluene decomposition reactions were not adsorbed onto its surface. The calorific value was not changed during the process and was higher than required for turbines and engines in every system studied.


  • Open Access

    Moist Biogas Conversion in a Plasma–Catalytic System

    by Michał Młotek, Michalina Perron, Katarzyna Tutaj, Krzysztof Krawczyk

    The limited resources of conventional fuels and their negative impact on the environment require scientists to search for alternative energy sources. One of the promising renewable sources of energy is biomass. The energy stored in biomass can be used in various ways. It can be combusted, gasified, or fermented, which leads to obtaining biogas. The main components of biogas are carbon dioxide and methane. The aim of this study was to convert in plasma and plasma–catalytic systems low methane biogas into a hydrogen and carbon monoxide mixture, which will allow for a wider range of potential applications. The combustible gas content increased in both systems. The effect of the water vapor content was investigated. It affects the conversion of CH4 and CO2 and significantly reduces soot formation (calculated by the carbon balance). It was possible to increase the content of flammable gases by about 20%. The highest molar fraction, 0.16, of hydrogen was obtained with the reduced cobalt catalyst.


  • Ammonia Decomposition in a Gliding Discharge Plasma

    by Michał Młotek, Michalina Perron, Krzysztof Krawczyk

    The negative impact of conventional fuels on the environment forces us to search for alternative energy sources. One of them is hydrogen. The only product of its combustion is water; however, transportation and storage are the problems. A solution could be ammonia which has a chemical hydrogen storage capacity as high as 17.8 wt%. NH3 as chemical energy storage can be used only if an efficient, rapid, and inexpensive method for its decomposition is known. Herein, the aim is to investigate the effect of gliding discharge plasma on the ammonia decomposition reaction. The novelty of this research is the use of high flow rates and high ammonia concentrations at the same time. The lowest energy consumption and the highest reaction rates of ammonia decomposition are obtained by using undiluted ammonia.


  • Open Access

    Decomposition of Tars on a Nickel Honeycomb Catalyst

    by Joanna Woroszył-Wojno, Michał Młotek, Michalina Perron, Paweł Jóźwik, Bogdan Ulejczyk, Krzysztof Krawczyk

    Biomass can be considered a renewable energy source. It undergoes a gasification process to obtain gaseous fuel, which converts it into combustible gaseous products such as hydrogen, carbon monoxide, and methane. The process also generates undesirable tars that can condense in gas lines and cause corrosion, and after processing, can be an additional source of combustible gases. This study focused on the processing of tar substances with toluene as a model substance. The effect of discharge power and carrier gas composition on toluene conversion was tested. The process was conducted in a plasma-catalytic system with a new Ni3Al system in the form of a honeycomb. The toluene conversion reached 90%, and small amounts of ethane, ethylene, acetylene, benzene, and C3 and C4 hydrocarbons were detected in the post-reaction mixture. Changes in the surface composition of the Ni3Al catalyst were observed throughout the experiments. These changes did not affect the toluene conversion.


  • Open Access

    Modification of PLA Scaffold Surface for Medical Applications

    by Michał Młotek, Agnieszka Gadomska-Gajadhur, Aleksandra Sobczak, Aleksandra Kruk, Michalina Perron, Krzysztof Krawczyk

    Materials used for medical applications (e.g., the cellular scaffold) should have not only the specific chemical composition, but the surface layer properties as well. For this reason, a method which enables an increase in the number of pores, wettability of the surface, and improvement the conditions of nutrient transportation into the membrane is being studied. The plasma of a dielectric barrier discharge was applied for the surface modification of polylactide obtained by dry or wet phase inversion. The plasma-modified surface was analyzed by contact angle measurements with water and diiodomethane. The surface free energy (SFE) was calculated by the Owens–Wendt method. The highest SFE and its polar component (67.6 mJ/m2 and 39.5 mJ/m2, respectively) were received when the process was conducted in an Ar + CO2 gas mixture with a discharge power of 20 W. The purpose of this research was to increase the wettability and porosity of the membrane’s surface. It can be concluded that the dielectric barrier discharge can effectively change the surface of the polylactide membranes, and that the structure of the modified membranes was not damaged during modification. The process of modification was easier for the membranes made by dry phase inversion. These materials had higher SFE values after the modification.


  • Open Access

    Coupled Plasma-Catalytic System with Rang 19pr Catalyst for Conversion of Tar

    by Michał Młotek, Joanna Woroszył, Bogdan Ulejczyk, Krzysztof Krawczyk

    A coupled plasma-catalytic system (CPCS) for the conversion of toluene was investigated and compared to the homogeneous system of gliding discharge plasma. Toluene was used as a model compound, which is present in tars. The study was carried out at atmospheric pressure, in a gas composition similar to the one obtained during pyrolysis of biomass. The effect of the initial toluene concentration, energy supplied to gliding discharge (GD) and the presence of a catalyst on the conversion of toluene was studied. Both the composition of outlet gas and its calorific value were monitored. Based on the obtained results it can be concluded that the conversion of toluene increases with the increase of gliding discharge power. The highest toluene conversion (89%) was received in the coupled plasma-catalytic system (catalyst: RANG-19PR) under the following conditions: CO (0.13 mol. fr.), CO2 (0.12 mol. fr.), H2 (0.25 mol. fr.), N2 (0.50 mol. fr.) and 4400 ppm of toluene with a gas flow rate of 1000 Nl/h. The composition of the outlet gas in the homogeneous system and in the CPCS changed in the range of a few percents. Toluene levels were reduced tenfold. Benzene, C3 and C4 hydrocarbons, as well as acetylene, ethylene and ethane, were detected in the outlet stream in trace amounts. Carbon deposits were present in the reactor. The products of methanation of carbon oxides were detected in the both studied systems. A mechanism of toluene decomposition in the CPCS was proposed. The application of the catalyst brought about an increase in the calorific value of the outlet gas. It was above the minimal level demanded by engines and turbines.


  • Hydrogen production from ethanol using dielectric barrier discharge

    by Bogdan Ulejczyk, Łukasz Nogal, Michał Młotek, Krzysztof Krawczyk


  • Modification of polyethylene tube surface in dielectric barrier discharge

    by Michał Młotek, Adam Błaszczyk, Krzysztof Krawczyk


  • Open Access

    Purification of the gas after pyrolysis in coupled plasma-catalytic system

    by Michał Młotek, Bogdan Ulejczyk, Joanna Woroszył, Irmina Walerczak, Krzysztof Krawczyk

    Gliding discharge and coupled plasma-catalytic system were used for toluene conversion in a gas composition such as the one obtained during pyrolysis of biomass. The chosen catalyst was G-0117, which is an industrial catalyst for methane conversion manufactured by INS Pulawy (Poland). The effects of discharge power, initial concentration of toluene, gas flow rate and the presence of the bed of the G-0117 catalyst on the conversion of C7H8, a model tars compounds were investigated. Conversion of coluene increases with discharge power and the highest one was noted in the coupled plasma-catalytic system. It was higher than that in the homogeneous system of gliding discharge. When applying a reactor with reduced G-0117 and CO (0.15 mol%), CO2 (0.15 mol%), H2 (0.30 mol%), N2 (0.40 mol%), 4000 ppm of toluene and gas flow rate of 1.5 Nm3/h, the conversion of toluene was higher than 99%. In the coupled plasma-catalytic system with G-0117 methanation of carbon oxides was observed.