Krzysztof Krawczyk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Krzysztof Krawczyk has a total of 64 co-authors. Here are the top co-authors by number of shared publications:
- Michał Młotek
Warsaw University of Technology, Poland
21 shared publications - Bogdan Ulejczyk
Faculty of Chemistry, Warsaw University of Technology, Noakowskiego 3, 00-664 Warszawa, Poland
20 shared publications Krzysztof Schmidt-Szałowski
Faculty of Chemistry, Warsaw University of Technology, Noakowskiego 3, 00-664 Warszawa, Poland
6 shared publications- Paweł Jóźwik
Faculty of Advanced Technologies and Chemistry, Institute of Materials Science and Engineering, Military University of Technology, Kaliskiego 2 Str., 00-908 Warsaw, Poland
6 shared publications - Łukasz Nogal
Electrical Power Engineering Institute, Warsaw University of Technology, 75 Koszykowa Street, 00-662 Warsaw, Poland
6 shared publications K. Schmidt-Szałowski
4 shared publications
Latest Publications
- Open Access
Toluene Decomposition in Plasma–Catalytic Systems with Nickel Catalysts on CaO-Al2O3 Carrier
The decomposition of toluene as a tar imitator in a gas composition similar to the gas after biomass pyrolysis was studied in a plasma–catalytic system. Nickel catalysts and the plasma from gliding arc discharge under atmospheric pressure were used. The effect of the catalyst bed, discharge power, initial toluene, and hydrogen concentration on C7H8 decomposition, calorific value, and unit energy consumption were studied. The gas flow rate was 1000 NL/h, while the inlet gas composition (molar ratio) was CO (0.13), CO2 (0.15), H2 (0.28–0.38), and N2 (0.34–0.44). The study was conducted using an initial toluene concentration in the range of 2000–4500 ppm and a discharge power of 1500–2000 W. In plasma–catalytic systems, the following catalysts were compared: NiO/Al2O3, NiO/(CaO-Al2O3), and Ni/(CaO-Al2O3). The decomposition of toluene increased with its initial concentration. An increase in hydrogen concentration resulted in higher activity of the Ni/(CaO-Al2O3) catalysts. The gas composition did not change by more than 10% during the process. Trace amounts of C2 hydrocarbons were observed. The conversion of C7H8 was up to 85% when NiO/(CaO-Al2O3) was used. The products of the toluene decomposition reactions were not adsorbed onto its surface. The calorific value was not changed during the process and was higher than required for turbines and engines in every system studied.
Open AccessToluene Decomposition in Plasma–Catalytic Systems with Nickel Catalysts on CaO-Al2O3 Carrier
The decomposition of toluene as a tar imitator in a gas composition similar to the gas after biomass pyrolysis was studied in a plasma–catalytic system. Nickel catalysts and the plasma from gliding arc discharge under atmospheric pressure were used. The effect of the catalyst bed, discharge power, initial toluene, and hydrogen concentration on C7H8 decomposition, calorific value, and unit energy consumption were studied. The gas flow rate was 1000 NL/h, while the inlet gas composition (molar ratio) was CO (0.13), CO2 (0.15), H2 (0.28–0.38), and N2 (0.34–0.44). The study was conducted using an initial toluene concentration in the range of 2000–4500 ppm and a discharge power of 1500–2000 W. In plasma–catalytic systems, the following catalysts were compared: NiO/Al2O3, NiO/(CaO-Al2O3), and Ni/(CaO-Al2O3). The decomposition of toluene increased with its initial concentration. An increase in hydrogen concentration resulted in higher activity of the Ni/(CaO-Al2O3) catalysts. The gas composition did not change by more than 10% during the process. Trace amounts of C2 hydrocarbons were observed. The conversion of C7H8 was up to 85% when NiO/(CaO-Al2O3) was used. The products of the toluene decomposition reactions were not adsorbed onto its surface. The calorific value was not changed during the process and was higher than required for turbines and engines in every system studied.
- Open Access
Efficient Conversion of Ethanol to Hydrogen in a Hybrid Plasma-Catalytic Reactor
The present work describes highly efficient hydrogen production from ethanol in a plasma-catalytic reactor depending on the discharge power and catalyst bed temperature. Hydrogen production increased as the power increased from 15 to 25 W. A further power increase to 35 W did not increase hydrogen production. The catalyst was already active at a temperature of 250 °C, and its activity increased with increasing temperature to 450 °C. The further temperature increase did not increase the activity of the cobalt catalyst. The most important advantage of using the catalyst was the increased ethanol conversion to CO2 instead of CO production. As a result, the hydrogen yield was very high and reached 4.1 mol(H2)/mol(C2H5OH). This result was obtained with a stoichiometric molar ratio of water to ethanol of 3.
Open AccessEfficient Conversion of Ethanol to Hydrogen in a Hybrid Plasma-Catalytic Reactor
The present work describes highly efficient hydrogen production from ethanol in a plasma-catalytic reactor depending on the discharge power and catalyst bed temperature. Hydrogen production increased as the power increased from 15 to 25 W. A further power increase to 35 W did not increase hydrogen production. The catalyst was already active at a temperature of 250 °C, and its activity increased with increasing temperature to 450 °C. The further temperature increase did not increase the activity of the cobalt catalyst. The most important advantage of using the catalyst was the increased ethanol conversion to CO2 instead of CO production. As a result, the hydrogen yield was very high and reached 4.1 mol(H2)/mol(C2H5OH). This result was obtained with a stoichiometric molar ratio of water to ethanol of 3.
- Open Access
Efficient Plasma Technology for the Production of Green Hydrogen from Ethanol and Water
This study concerns the production of hydrogen from a mixture of ethanol and water. The process was conducted in plasma generated by a spark discharge. The substrates were introduced in the liquid phase into the reactor. The gaseous products formed in the spark reactor were hydrogen, carbon monoxide, carbon dioxide, methane, acetylene, and ethylene. Coke was also produced. The energy efficiency of hydrogen production was 27 mol(H2)/kWh, and it was 36% of the theoretical energy efficiency. The high value of the energy efficiency of hydrogen production was obtained with relatively high ethanol conversion (63%). In the spark discharge, it was possible to conduct the process under conditions in which the ethanol conversion reached 95%. However, this entailed higher energy consumption and reduced the energy efficiency of hydrogen production to 8.8 mol(H2)/kWh. Hydrogen production increased with increasing discharge power and feed stream. However, the hydrogen concentration was very high under all tested conditions and ranged from 57.5 to 61.5%. This means that the spark reactor is a device that can feed fuel cells, the power load of which can fluctuate.
Open AccessEfficient Plasma Technology for the Production of Green Hydrogen from Ethanol and Water
This study concerns the production of hydrogen from a mixture of ethanol and water. The process was conducted in plasma generated by a spark discharge. The substrates were introduced in the liquid phase into the reactor. The gaseous products formed in the spark reactor were hydrogen, carbon monoxide, carbon dioxide, methane, acetylene, and ethylene. Coke was also produced. The energy efficiency of hydrogen production was 27 mol(H2)/kWh, and it was 36% of the theoretical energy efficiency. The high value of the energy efficiency of hydrogen production was obtained with relatively high ethanol conversion (63%). In the spark discharge, it was possible to conduct the process under conditions in which the ethanol conversion reached 95%. However, this entailed higher energy consumption and reduced the energy efficiency of hydrogen production to 8.8 mol(H2)/kWh. Hydrogen production increased with increasing discharge power and feed stream. However, the hydrogen concentration was very high under all tested conditions and ranged from 57.5 to 61.5%. This means that the spark reactor is a device that can feed fuel cells, the power load of which can fluctuate.
- Open Access
Plasma-Catalytic Process of Hydrogen Production from Mixture of Methanol and Water
In the present work the process of hydrogen production was conducted in the plasma-catalytic reactor, the substrates were first treated with plasma and then introduced into the catalyst bed. Plasma was produced by a spark discharge. The discharge power ranged from 15 to 46 W. The catalyst was metallic nickel supported on Al2O3. The catalyst was active from a temperature of 400 °C. The substrate flow rate was 1 mol/h of water and 1 mol/h of methanol. The process generated H2, CO, CO2 and CH4. The gas which formed the greatest amount was H2. Its concentration in the gas was ~60%. The conversion of methanol and the production of hydrogen in the plasma-catalytic reactor were higher than in the plasma and catalytic reactors. The synergy effect of the interaction of two environments, i.e., plasma and the catalyst, was observed. The highest hydrogen production was 1.38 mol/h and the highest methanol conversion was 64%. The increased in the discharge power resulted in increasing methanol conversion and hydrogen production.
Open AccessPlasma-Catalytic Process of Hydrogen Production from Mixture of Methanol and Water
In the present work the process of hydrogen production was conducted in the plasma-catalytic reactor, the substrates were first treated with plasma and then introduced into the catalyst bed. Plasma was produced by a spark discharge. The discharge power ranged from 15 to 46 W. The catalyst was metallic nickel supported on Al2O3. The catalyst was active from a temperature of 400 °C. The substrate flow rate was 1 mol/h of water and 1 mol/h of methanol. The process generated H2, CO, CO2 and CH4. The gas which formed the greatest amount was H2. Its concentration in the gas was ~60%. The conversion of methanol and the production of hydrogen in the plasma-catalytic reactor were higher than in the plasma and catalytic reactors. The synergy effect of the interaction of two environments, i.e., plasma and the catalyst, was observed. The highest hydrogen production was 1.38 mol/h and the highest methanol conversion was 64%. The increased in the discharge power resulted in increasing methanol conversion and hydrogen production.
- Open Access
Decomposition of Tars on a Nickel Honeycomb Catalyst
Biomass can be considered a renewable energy source. It undergoes a gasification process to obtain gaseous fuel, which converts it into combustible gaseous products such as hydrogen, carbon monoxide, and methane. The process also generates undesirable tars that can condense in gas lines and cause corrosion, and after processing, can be an additional source of combustible gases. This study focused on the processing of tar substances with toluene as a model substance. The effect of discharge power and carrier gas composition on toluene conversion was tested. The process was conducted in a plasma-catalytic system with a new Ni3Al system in the form of a honeycomb. The toluene conversion reached 90%, and small amounts of ethane, ethylene, acetylene, benzene, and C3 and C4 hydrocarbons were detected in the post-reaction mixture. Changes in the surface composition of the Ni3Al catalyst were observed throughout the experiments. These changes did not affect the toluene conversion.
Open AccessDecomposition of Tars on a Nickel Honeycomb Catalyst
Biomass can be considered a renewable energy source. It undergoes a gasification process to obtain gaseous fuel, which converts it into combustible gaseous products such as hydrogen, carbon monoxide, and methane. The process also generates undesirable tars that can condense in gas lines and cause corrosion, and after processing, can be an additional source of combustible gases. This study focused on the processing of tar substances with toluene as a model substance. The effect of discharge power and carrier gas composition on toluene conversion was tested. The process was conducted in a plasma-catalytic system with a new Ni3Al system in the form of a honeycomb. The toluene conversion reached 90%, and small amounts of ethane, ethylene, acetylene, benzene, and C3 and C4 hydrocarbons were detected in the post-reaction mixture. Changes in the surface composition of the Ni3Al catalyst were observed throughout the experiments. These changes did not affect the toluene conversion.
- Open Access
Investigation of Co3O4 and LaCoO3 Interaction by Performing N2O Decomposition Tests under Co3O4-CoO Transition Temperature
The research presented in this paper addresses the question: How does the addition of a small amount of LaCoO3 impact the activity of a Co3O4 catalyst? By testing such a catalyst in N2O decomposition under conditions at which the thermal decomposition of Co3O4 to CoO is possible, one gains unique insight into how the two phases interact. The activity of such a catalyst increases in the entire studied temperature range, unlike the activity of the undoped cobalt catalyst which is lower at 850 °C than at 800 °C due to the reduction of Co3O4 to CoO. XRD measurements showed that CoO was also the main cobalt oxide present in the Co3.5La catalyst after operating at 850 °C, as did the XPS measurements, but there was no drop of activity associated with this change. The influence of NO, O2 and H2O on the activity of the new catalyst, Co3.5La, was determined. Lack of positive effect of NO, a known oxygen scavenger, on the activity was noticed at all temperatures, showing that the effect of LaCoO3 is probably due to increased oxygen desorption. Temperature programed oxidation (TPO) tests showed that the beneficial effects of the presence of LaCoO3 on the activity of cobalt oxide at 850 °C were probably caused by enhanced diffusion of O2− anions through the entire catalyst, which facilitates desorption of oxygen molecules from the surface.
Open AccessInvestigation of Co3O4 and LaCoO3 Interaction by Performing N2O Decomposition Tests under Co3O4-CoO Transition Temperature
The research presented in this paper addresses the question: How does the addition of a small amount of LaCoO3 impact the activity of a Co3O4 catalyst? By testing such a catalyst in N2O decomposition under conditions at which the thermal decomposition of Co3O4 to CoO is possible, one gains unique insight into how the two phases interact. The activity of such a catalyst increases in the entire studied temperature range, unlike the activity of the undoped cobalt catalyst which is lower at 850 °C than at 800 °C due to the reduction of Co3O4 to CoO. XRD measurements showed that CoO was also the main cobalt oxide present in the Co3.5La catalyst after operating at 850 °C, as did the XPS measurements, but there was no drop of activity associated with this change. The influence of NO, O2 and H2O on the activity of the new catalyst, Co3.5La, was determined. Lack of positive effect of NO, a known oxygen scavenger, on the activity was noticed at all temperatures, showing that the effect of LaCoO3 is probably due to increased oxygen desorption. Temperature programed oxidation (TPO) tests showed that the beneficial effects of the presence of LaCoO3 on the activity of cobalt oxide at 850 °C were probably caused by enhanced diffusion of O2− anions through the entire catalyst, which facilitates desorption of oxygen molecules from the surface.
- Open Access
- 18 February 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (4) , 1815
Modification of PLA Scaffold Surface for Medical Applications
Materials used for medical applications (e.g., the cellular scaffold) should have not only the specific chemical composition, but the surface layer properties as well. For this reason, a method which enables an increase in the number of pores, wettability of the surface, and improvement the conditions of nutrient transportation into the membrane is being studied. The plasma of a dielectric barrier discharge was applied for the surface modification of polylactide obtained by dry or wet phase inversion. The plasma-modified surface was analyzed by contact angle measurements with water and diiodomethane. The surface free energy (SFE) was calculated by the Owens–Wendt method. The highest SFE and its polar component (67.6 mJ/m2 and 39.5 mJ/m2, respectively) were received when the process was conducted in an Ar + CO2 gas mixture with a discharge power of 20 W. The purpose of this research was to increase the wettability and porosity of the membrane’s surface. It can be concluded that the dielectric barrier discharge can effectively change the surface of the polylactide membranes, and that the structure of the modified membranes was not damaged during modification. The process of modification was easier for the membranes made by dry phase inversion. These materials had higher SFE values after the modification.
- 18 February 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (4) , 1815
Open AccessModification of PLA Scaffold Surface for Medical Applications
Materials used for medical applications (e.g., the cellular scaffold) should have not only the specific chemical composition, but the surface layer properties as well. For this reason, a method which enables an increase in the number of pores, wettability of the surface, and improvement the conditions of nutrient transportation into the membrane is being studied. The plasma of a dielectric barrier discharge was applied for the surface modification of polylactide obtained by dry or wet phase inversion. The plasma-modified surface was analyzed by contact angle measurements with water and diiodomethane. The surface free energy (SFE) was calculated by the Owens–Wendt method. The highest SFE and its polar component (67.6 mJ/m2 and 39.5 mJ/m2, respectively) were received when the process was conducted in an Ar + CO2 gas mixture with a discharge power of 20 W. The purpose of this research was to increase the wettability and porosity of the membrane’s surface. It can be concluded that the dielectric barrier discharge can effectively change the surface of the polylactide membranes, and that the structure of the modified membranes was not damaged during modification. The process of modification was easier for the membranes made by dry phase inversion. These materials had higher SFE values after the modification.
- 28 August 2018
- Published by Springer Nature in Journal of Materials Research
- Vol. 33 (16) , 2396-2403
Modification of polyethylene tube surface in dielectric barrier discharge
- 28 August 2018
- Published by Springer Nature in Journal of Materials Research
- Vol. 33 (16) , 2396-2403
Modification of polyethylene tube surface in dielectric barrier discharge
- Open Access
- 1 December 2017
- Published by Walter de Gruyter GmbH in Polish Journal of Chemical Technology
- Vol. 19 (4) , 94-98
Purification of the gas after pyrolysis in coupled plasma-catalytic system
Gliding discharge and coupled plasma-catalytic system were used for toluene conversion in a gas composition such as the one obtained during pyrolysis of biomass. The chosen catalyst was G-0117, which is an industrial catalyst for methane conversion manufactured by INS Pulawy (Poland). The effects of discharge power, initial concentration of toluene, gas flow rate and the presence of the bed of the G-0117 catalyst on the conversion of C7H8, a model tars compounds were investigated. Conversion of coluene increases with discharge power and the highest one was noted in the coupled plasma-catalytic system. It was higher than that in the homogeneous system of gliding discharge. When applying a reactor with reduced G-0117 and CO (0.15 mol%), CO2 (0.15 mol%), H2 (0.30 mol%), N2 (0.40 mol%), 4000 ppm of toluene and gas flow rate of 1.5 Nm3/h, the conversion of toluene was higher than 99%. In the coupled plasma-catalytic system with G-0117 methanation of carbon oxides was observed.
- 1 December 2017
- Published by Walter de Gruyter GmbH in Polish Journal of Chemical Technology
- Vol. 19 (4) , 94-98
Open AccessPurification of the gas after pyrolysis in coupled plasma-catalytic system
Gliding discharge and coupled plasma-catalytic system were used for toluene conversion in a gas composition such as the one obtained during pyrolysis of biomass. The chosen catalyst was G-0117, which is an industrial catalyst for methane conversion manufactured by INS Pulawy (Poland). The effects of discharge power, initial concentration of toluene, gas flow rate and the presence of the bed of the G-0117 catalyst on the conversion of C7H8, a model tars compounds were investigated. Conversion of coluene increases with discharge power and the highest one was noted in the coupled plasma-catalytic system. It was higher than that in the homogeneous system of gliding discharge. When applying a reactor with reduced G-0117 and CO (0.15 mol%), CO2 (0.15 mol%), H2 (0.30 mol%), N2 (0.40 mol%), 4000 ppm of toluene and gas flow rate of 1.5 Nm3/h, the conversion of toluene was higher than 99%. In the coupled plasma-catalytic system with G-0117 methanation of carbon oxides was observed.