Sheikh Shah Khaleduzzaman

This paper reports on modelling outcomes for improvements to building energy performance in Indonesia. Long-term climate effects due to building energy demand and carbon emissions are also considered. The global change assessment model (GCAM) was used to generate the related end-user building energy data, including socioeconomics, for urban areas of Indonesia. As a comprehensive study, the total life cycle of carbon in the building sector and the concept of zero-carbon buildings, including energy efficiency, zero-emissions electricity and fuel-switching options, were considered. Building shell conductance (U-value) of the building envelope, floor area ratio (FAR), air conditioner (AC) efficiency, electrical appliance (APL) efficiency, rooftop photovoltaic (PV) performance and ground source heat pump (GSHP) systems were considered as parameters to mitigate carbon emissions under the operational energy category in the GCAM. Carbon mitigation associated with the cement production process was considered in the raw material category. Urban population and labour productivity in Indonesia were used as base inputs with projected growth rates to 2050 determined from the available literature. Low growth rate ‘LowRate’ and high growth rate ‘HighRate’ were considered as variable inputs for U-value, FAR, AC efficiency, APLs efficiency and PV capacity factor to model emissions mitigation. The energy consumption of the GSHP was compared to the conventional reverse cycle ACs to identify the potential of the GSHP as a fuel-switching option. In the GCAM, the benchmark (base case scenario) data set was generated based on input parameters (urban population and labour productivity rate) only for the residential building sector in Indonesia. Total potential carbon emissions mitigation was found to be 432 Mt CO₂-e for the residential building sector in Indonesia over 2020–2050. It was found that an average of 24% carbon emissions mitigation could be achieved by 2020–2030 and 76% by 2031–2050.

This paper reports modelling outcomes for improvements to building energy performance in Indonesia. Long-term climate effects due to building energy demands including carbon emissions are also considered. The global change assessment model (GCAM) was used to generate the related end-user building energy data, including socioeconomics for urban areas of Indonesia. As a comprehensive study, the total life cycle of carbon in the building sector and the concept of zero-carbon buildings, including energy efficiency, zero-emissions electricity and fuel switching options were considered. Building shell conductance (u-value) of building envelope, floor area ratio (FAR), air conditioner (AC) efficiency, electrical appliances (APLs) efficiency, rooftop photovoltaic (PV) performance and ground source heat pump (GSHP) systems were considered as parameters to mitigate carbon emissions under the operational energy category in GCAM. Carbon mitigation associated with the cement production process was considered in the raw material category. Urban population and labour productivity in Indonesia were used as base inputs with projected growth rates to 2050 determined from available literature. Low growth rate ‘LowRate’ and high growth rate ‘HighRate’ were considered as variable inputs for u-value, FAR, AC efficiency, APLs efficiency, and PV capacity factor to model emissions mitigation. The energy consumption of the GSHP was compared to the conventional reverse cycle ACs to identify the potential of the GSHP as a fuel-switching option. Only base input data were used for cement production process parameters without applying any variable inputs. GCAM base scenarios based on input data only (without modifying variable data) for the residential building sector in Indonesia were considered the benchmark for this study. Total potential carbon emissions mitigation was found to be 432 Mt CO2-e for the residential building sector in Indonesia over 2020-2050. It was found that an average of 24% carbon emissions mitigation could be achieved by 2020-30 and 76% in 2031-2050.

In this paper, a modified bald eagle search optimization algorithm was applied for the first time to determine the parameters of the triple diode model (TDM) of perovskite solar cells (PSCs). Two experimental datasets are considered; the first is measured I–V points for a PSC at standard conditions. The second consists of the measured I–V points for a modified PSC. In contrast, the cost function to be minimized is the root mean square error (RMSE) between the experimental dataset and the calculated one. To prove the superiority of modified bald eagle search optimization (mBES), a comparison with the original bald eagle search optimization (BES), particle swarm optimizer (PSO), Hunger games search (HGS), and recent Coronavirus Disease Optimization Algorithm (COVIDOA) was implemented. Furthermore, statistical analysis of ANOVA and Tukey tests was performed. The results demonstrate the lead of the recommended mBES in identifying the parameters of the TDM for PSCs, where the RMSE achieved the least value among the used optimization algorithms in this study.

Adsorption heat storage is the most feasible technology for heating decarbonization, which can store large quantities of waste and renewable heat for an exceptionally long time. However, utilizing adsorption heat storage in geographical locations with sub-zero ambient conditions is challenging. Therefore, this paper experimentally investigates the use of ethanol as a working fluid paired with silica gel for adsorption heat storage and utilizes sub-zero ambient as the heat source. The heat storage characteristics, heat charging/discharging cyclic performance, and energy conversion performance via exergy analysis were determined under realistic operating conditions and benchmarked against the widely investigated silica gel/water. Ethanol adsorbate was successfully utilized as a working fluid to employ the evaporators operating under sub-zero ambient conditions. Silica gel/ethanol showed the most significant net cyclic uptake, twice that of silica gel/water. However, the physical characteristics of ethanol molecules led to a degree of non-desorbed fluid, which hampered such potential to store 18.08 kJ/kg_ads under a sub-zero evaporator temperature and 24.84 kJ/kg_ads for an above-zero evaporator temperature compared to silica gel of 155.12 kJ/kg_ads operating an above-zero evaporator temperature. On the other hand, silica gel/ethanol showed the fastest heat charging/discharging rate that can shorten the cycle time by 45%. The major contributor to exergy destruction was the exergy transferred by charging heat, which was five times the discharging heat due to the high charging temperature.

The use of solar thermal systems (STSs) has recently reached a significant edge. The increasing research on developing an alternative power supply for limiting fossil fuel usage and climate change are the driving forces of STSs. The current work explores the recent progress in STSs’ applications, including PV/T or “photovoltaic/thermal” systems, zero-energy buildings, greenhouse solar thermal applications, solar thermal for pumping water, solar thermal refrigerators, solar chimneys, water desalination, and solar collectors, along with the benefits and challenges of these applications. Then, the potential contribution of STSs in achieving the various SDGs or “Sustainable development goals”, including barriers and research gaps, are elaborated. In brief, STSs significantly contribute to the seventeen SDGs’ achievement directly and indirectly. Recent developments in the engineering applications of STSs are strongly based on the materials of construction, as well as their design, process optimisation, and integration with multidisciplinary sciences and technologies such as modelling, nanoscience/nanotechnology, and artificial intelligence.

Photovoltaic-thermal (PVT) technologies have demonstrated several attractive features, such as higher power and comparative efficiencies. Improving the thermal recovery from the PVT system would further improve the power output and the efficiency of the PVT system. This paper identifies the best operating factors of nanofluid-based PV thermal/nano-enhanced phase change material using artificial intelligence. The target is the maximization of thermal energy and exergy outputs. The suggested approach combines ANFIS modelling and particle swarm optimization (PSO). Four operating factors are taken into consideration: PCM (phase change material) layer thickness, HTF (heat transfer fluid) mass flow rate, MFNPCM (“mass fraction of nanoparticles in PCM”) and MFNfluid (“mass fraction of nanoparticles in nanofluid”). Using a dataset, an “adaptive neuro-fuzzy inference system” (ANFIS) model has been established for simulating the thermal energy and exergy outputs in terms of the mentioned operating factors. Then, using PSO, the best values of PCM thickness, mass flow rate, MFNPCM and MFNfluid are estimated. The proposed model’s accuracy was examined by comparing the results with those obtained by response surface methodology and the experimental dataset.

Metal–air batteries are a promising technology that could be used in several applications, from portable devices to large-scale energy storage applications. This work is a comprehensive review of the recent progress made in metal-air batteries MABs. It covers the theoretical considerations and mechanisms of MABs, electrochemical performance, and the progress made in the development of different structures of MABs. The operational concepts and recent developments in MABs are thoroughly discussed, with a particular focus on innovative materials design and cell structures. The classical research on traditional MABs was chosen and contrasted with metal–air flow systems, demonstrating the merits associated with the latter in terms of achieving higher energy density and efficiency, along with stability. Furthermore, the recent applications of MABs were discussed. Finally, a broad overview of challenges/opportunities and potential directions for commercializing this technology is carefully discussed. The primary focus of this investigation is to present a concise summary and to establish future directions in the development of MABs from traditional static to advanced flow technologies. A systematic analysis of this subject from a material and chemistry standpoint is presented as well.