Bartosz Jurkiewicz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Bartosz Jurkiewicz has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Beata Smyrak
Faculty of Nonferous Metals, AGH University of Krakow, 30-059 Krakow, Poland
5 shared publications - Tadeusz Knych
Faculty of Non-Ferrous Metals, AGH University of Krakow, 30-059 Krakow, Poland
5 shared publications - Krystian Franczak
Faculty of Non-Ferrous Metals, AGH University of Krakow, 30-059 Krakow, Poland
4 shared publications - Małgorzata Zasadzińska
Faculty of Non-Ferrous Metals, AGH University of Krakow, al. Mickiewicza 30, 30-059 Krakow, Poland
4 shared publications - Paweł Strzępek
Faculty of Non-Ferrous Metals, AGH University of Krakow, Krakow, Poland
4 shared publications - Andrzej Mamala
AGH University of Science and Technology
2 shared publications
Latest Publications
- Open Access
- 15 July 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 151 (1) , 4
Investigation of the Influence of Drawing Process Parameters on the Fatigue Strength of Aluminium Wires Intended for Overhead Power Line Conductors
One of the primary factors contributing to the impairment of overhead power lines during operation is fatigue damage arising from conductor vibration. Several factors influence the fatigue strength, including chemical composition, strength, surface quality, and residual stresses. One solution to increase the fatigue strength of these lines is to replace aluminium with a higher-strength aluminium alloy. Unfortunately, this option is costly and has a detrimental effect on the electrical conductivity of the wire. Consequently, a further research direction for improving fatigue strength involves modifying the surface quality and reducing residual stresses in wires. This article presents research findings focused on the influence of drawing parameters of aluminium wires—including modification of the die geometry—on fatigue strength. In this study, wires were produced using dies with different geometries via the high-speed industrial wire drawing process. Surface quality (SEM), 3D surface topography, and fatigue strength tests were then carried out on the aluminium wires. Following a thorough review of the research results, it was determined that optimising the die geometry is the most effective way to achieve higher fatigue strength for aluminium wires under industrial conditions.
- 15 July 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 151 (1) , 4
Open AccessInvestigation of the Influence of Drawing Process Parameters on the Fatigue Strength of Aluminium Wires Intended for Overhead Power Line Conductors
One of the primary factors contributing to the impairment of overhead power lines during operation is fatigue damage arising from conductor vibration. Several factors influence the fatigue strength, including chemical composition, strength, surface quality, and residual stresses. One solution to increase the fatigue strength of these lines is to replace aluminium with a higher-strength aluminium alloy. Unfortunately, this option is costly and has a detrimental effect on the electrical conductivity of the wire. Consequently, a further research direction for improving fatigue strength involves modifying the surface quality and reducing residual stresses in wires. This article presents research findings focused on the influence of drawing parameters of aluminium wires—including modification of the die geometry—on fatigue strength. In this study, wires were produced using dies with different geometries via the high-speed industrial wire drawing process. Surface quality (SEM), 3D surface topography, and fatigue strength tests were then carried out on the aluminium wires. Following a thorough review of the research results, it was determined that optimising the die geometry is the most effective way to achieve higher fatigue strength for aluminium wires under industrial conditions.
- Open Access
A Comparative Analysis of the Fatigue Strength of Aluminium and Copper Wires Used for Power Cables
Recent studies have demonstrated that the utilisation of aluminium in electrical applications has increased substantially, particularly in the context of power cables. The substitution of copper with aluminium in cable fabrication is predominantly driven by economic considerations. When designing such cables, it is imperative to ascertain their functional properties, including their electrical conductivity and mechanical properties, and their operational properties, which include rheological, thermal, and material fatigue resistance. This is to ensure that the aluminium and copper cables are compatible. The primary challenge confronting researchers in this domain pertains to predicting and forecasting the failure of overhead cables during their operational lifecycle. One of the most significant and prevalent operational hazards is fatigue damage. This article presents the experimental results of fatigue tests on single Al and Cu wires in various states of mechanical reinforcement. The parameters of the Wöhler curve were determined, and a comparative analysis of the morphology of fatigue damage in single copper and aluminium wires was performed. It was found that copper wires are more fatigue-resistant than aluminium wires. In the case of high-cycle fatigue, this difference can amount to 106 cycles. An analysis of fatigue fracture morphology showed that fractures have a developed surface and that plastic deformation makes a significant contribution in the case of low-cycle fatigue. In the case of high-cycle fatigue, many cracks were observed in the copper wires. No such cracks were observed in the aluminium wires.
Open AccessA Comparative Analysis of the Fatigue Strength of Aluminium and Copper Wires Used for Power Cables
Recent studies have demonstrated that the utilisation of aluminium in electrical applications has increased substantially, particularly in the context of power cables. The substitution of copper with aluminium in cable fabrication is predominantly driven by economic considerations. When designing such cables, it is imperative to ascertain their functional properties, including their electrical conductivity and mechanical properties, and their operational properties, which include rheological, thermal, and material fatigue resistance. This is to ensure that the aluminium and copper cables are compatible. The primary challenge confronting researchers in this domain pertains to predicting and forecasting the failure of overhead cables during their operational lifecycle. One of the most significant and prevalent operational hazards is fatigue damage. This article presents the experimental results of fatigue tests on single Al and Cu wires in various states of mechanical reinforcement. The parameters of the Wöhler curve were determined, and a comparative analysis of the morphology of fatigue damage in single copper and aluminium wires was performed. It was found that copper wires are more fatigue-resistant than aluminium wires. In the case of high-cycle fatigue, this difference can amount to 106 cycles. An analysis of fatigue fracture morphology showed that fractures have a developed surface and that plastic deformation makes a significant contribution in the case of low-cycle fatigue. In the case of high-cycle fatigue, many cracks were observed in the copper wires. No such cracks were observed in the aluminium wires.
- Open Access
Studies on the Evolution of Fatigue Strength of Aluminium Wires for Overhead Line Conductors
Traditional ACSR overhead wires, which consist of a high-strength steel core and several layers of aluminium wires, are currently the most popular overhead line conductor (OHL) design globally. Operating conditions, particularly operating under varying stresses from Karman vortices, lead to the fatigue cracking of wires of the outer layer, followed by wires of the inner layers. Karman vortices are formed by the detachment of a laminar wind stream flowing around the conductor, which causes vibrations in the conductor called wind or aeolian oscillations. Aluminium wires are manufactured using standard batch material drawing technology. Although the fatigue strength of such wires is not standardised, there are various criteria for evaluating this characteristic, as well as established limits on the number of cycles needed to break the first wires of the outer layer. Fatigue strength also strongly depends on the geometric structure of the wire and its operating conditions. The article analyses the influence of the mechanical condition of aluminium wires used in ACSR cables on their fatigue strength. We then present results from aluminium wire fatigue tests conducted on a specially constructed test rig. In addition, fatigue cracks were interpreted using scanning microscopy.
Open AccessStudies on the Evolution of Fatigue Strength of Aluminium Wires for Overhead Line Conductors
Traditional ACSR overhead wires, which consist of a high-strength steel core and several layers of aluminium wires, are currently the most popular overhead line conductor (OHL) design globally. Operating conditions, particularly operating under varying stresses from Karman vortices, lead to the fatigue cracking of wires of the outer layer, followed by wires of the inner layers. Karman vortices are formed by the detachment of a laminar wind stream flowing around the conductor, which causes vibrations in the conductor called wind or aeolian oscillations. Aluminium wires are manufactured using standard batch material drawing technology. Although the fatigue strength of such wires is not standardised, there are various criteria for evaluating this characteristic, as well as established limits on the number of cycles needed to break the first wires of the outer layer. Fatigue strength also strongly depends on the geometric structure of the wire and its operating conditions. The article analyses the influence of the mechanical condition of aluminium wires used in ACSR cables on their fatigue strength. We then present results from aluminium wire fatigue tests conducted on a specially constructed test rig. In addition, fatigue cracks were interpreted using scanning microscopy.
- Open Access
- 27 February 2020
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 20 (1) , 1-15
Research of mechanical and electrical properties of Cu–Sc and Cu–Zr alloys
The research paper presents the impact of the scandium additive and various conditions of the heat treatment on copper mechanical, electrical and heat resistance properties. The performed research works included manufacturing of CuSc0.15 and CuSc0.3 alloys through metallurgical synthesis with the use of induction furnace and following crystallization in graphite crucibles at ambient temperature. Additionally, a CuZr0.15 alloy was produced as a reference material for previously synthesized Cu–Sc alloys. During research, the selection of heat treatment for the produced materials was conducted in order to obtain the highest mechanical–electrical properties ratio. Materials obtained in such a way were next subjected to thermal resistance tests. Parameters of thermal resistance test included temperatures from the range of 200–700 °C and 1 h of annealing time. The research has shown that CuSc0.15 and CuSc0.3 alloys have higher heat resistance after their precipitation hardening compared to the Cu–Zr alloy. The paper also presents microstructural research of the produced materials, which showed that alloying elements precipitates are mainly localized at the grain boundaries of the material structure.
- 27 February 2020
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 20 (1) , 1-15
Open AccessResearch of mechanical and electrical properties of Cu–Sc and Cu–Zr alloys
The research paper presents the impact of the scandium additive and various conditions of the heat treatment on copper mechanical, electrical and heat resistance properties. The performed research works included manufacturing of CuSc0.15 and CuSc0.3 alloys through metallurgical synthesis with the use of induction furnace and following crystallization in graphite crucibles at ambient temperature. Additionally, a CuZr0.15 alloy was produced as a reference material for previously synthesized Cu–Sc alloys. During research, the selection of heat treatment for the produced materials was conducted in order to obtain the highest mechanical–electrical properties ratio. Materials obtained in such a way were next subjected to thermal resistance tests. Parameters of thermal resistance test included temperatures from the range of 200–700 °C and 1 h of annealing time. The research has shown that CuSc0.15 and CuSc0.3 alloys have higher heat resistance after their precipitation hardening compared to the Cu–Zr alloy. The paper also presents microstructural research of the produced materials, which showed that alloying elements precipitates are mainly localized at the grain boundaries of the material structure.
- 1 May 2019
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 19 (3) , 862-870
The researches of influence of strengthening on fatigue strength of aluminium wires for OHL conductors
- 1 May 2019
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 19 (3) , 862-870
The researches of influence of strengthening on fatigue strength of aluminium wires for OHL conductors
- 21 March 2019
- Published by Elsevier in Cryogenics
- Vol. 100, 11-17
Research on the drawing process of Cu and CuZn wires obtained in the cryogenic conditions
- 21 March 2019
- Published by Elsevier in Cryogenics
- Vol. 100, 11-17
Research on the drawing process of Cu and CuZn wires obtained in the cryogenic conditions
- 16 October 2018
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 19 (1) , 186-193
Analysis of the strengthening and recrystallization of electrolytic copper (Cu-ETP) and oxygen free copper (Cu-OF)
- 16 October 2018
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 19 (1) , 186-193
Analysis of the strengthening and recrystallization of electrolytic copper (Cu-ETP) and oxygen free copper (Cu-OF)
- 5 January 2017
- Published by Wydawnictwo SIGMA-NOT, sp. z.o.o. in HUTNIK - WIADOMOŚCI HUTNICZE
- Vol. 1 (1) , 19-21
Badania wytrzymałości zmęczeniowej drutów na bazie miedzi i aluminium stosowanych w elektroenergetyce napowietrznej i
Wydawnictwo SIGMA-NOT wydaje czasopisma fachowe informuj?ce swoich czytelnik?w o najnowszych osi?gni?ciach naukowych i nowoczesnych rozwi?zaniach technicznych w Polsce i na ?wiecie, popularyzuje problemy techniczne oraz poszerza wiedz? i kultur? techniczn?.
- 5 January 2017
- Published by Wydawnictwo SIGMA-NOT, sp. z.o.o. in HUTNIK - WIADOMOŚCI HUTNICZE
- Vol. 1 (1) , 19-21
Badania wytrzymałości zmęczeniowej drutów na bazie miedzi i aluminium stosowanych w elektroenergetyce napowietrznej i
Wydawnictwo SIGMA-NOT wydaje czasopisma fachowe informuj?ce swoich czytelnik?w o najnowszych osi?gni?ciach naukowych i nowoczesnych rozwi?zaniach technicznych w Polsce i na ?wiecie, popularyzuje problemy techniczne oraz poszerza wiedz? i kultur? techniczn?.
- 15 February 2016
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 682, 138-142
Research of Chemical Composition Influence on the Mechanical and Electrical Properties of Al-Mg-Si Wires
The subject of the work focuses on hardened-precipitation type alloys Al-Mg-Si which constitute the primary component material used to build homogeneous electric wires, type AAAC (All Aluminium Alloy Conductor). The material in consideration is a well-known and well-studied alloy, particularly in terms of the possibilities for using it in thermal treatment processes. However, the subject literature does not present a comprehensive recognition of the effect of heat treatment parameters on the set of mechanical and electrical properties in wires grade 6101. In particular, the study presents the results of experiments that show the possibility of controlling the AlMgSi wire properties by means of selecting the heat treatment parameters for simultaneously obtaining a high tensile strength and high electrical conductivity. Hence, the research described in this paper focuses mostly on determining the impact of the Mg and Si content on the electrical and mechanical properties of wires of Al-Mg-Si wire alloys.
- 15 February 2016
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 682, 138-142
Research of Chemical Composition Influence on the Mechanical and Electrical Properties of Al-Mg-Si Wires
The subject of the work focuses on hardened-precipitation type alloys Al-Mg-Si which constitute the primary component material used to build homogeneous electric wires, type AAAC (All Aluminium Alloy Conductor). The material in consideration is a well-known and well-studied alloy, particularly in terms of the possibilities for using it in thermal treatment processes. However, the subject literature does not present a comprehensive recognition of the effect of heat treatment parameters on the set of mechanical and electrical properties in wires grade 6101. In particular, the study presents the results of experiments that show the possibility of controlling the AlMgSi wire properties by means of selecting the heat treatment parameters for simultaneously obtaining a high tensile strength and high electrical conductivity. Hence, the research described in this paper focuses mostly on determining the impact of the Mg and Si content on the electrical and mechanical properties of wires of Al-Mg-Si wire alloys.
- 15 February 2016
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 682, 61-68
New Aluminum Base Materials for Use on Electrical Purposes
Modern power industry expects new, dedicated aluminum based alloys with non-standard properties, including increased resistance to temperature. Materials exhibiting higher thermal resistance allow to increase operating temperature of electrical conductors, which results in the increase of their current carrying capacity. Commonly known and used in such applications are alloys from the AlZr group. Despite their advantages scientists from around the world are searching for new alternatives. In this paper authors present research results on Al-Mo and Al-Ag alloys with particular interest to the analysis of the molybdenum addition to the aluminum in the amount of 0.05, 0.1, 0.2% and silver addition in the amount of 0.05, 0.1, 0.15% by mass on the mechanical and electrical properties of obtained alloys. Tests were also carried out for reference material which is high-purity aluminum and the AlZr alloy, both in the as cast state temper. Results showed a significant change of temperature coefficient of resistance in Al-Ag alloys compared to Al, which leads to possible increase of the Joule’a heat without the raise of conductors temperature limit. On the other hand, above-average heat resistance of alloys from the Al-Mo group of materials was achieved during the trials. On that basis authors state that Al-Ag alloys may be used for the production of ACSS conductors and Al-Mo alloys for TACSR or TACIR type of conductors.This study was performed under a project financed by NCBiR within the INNOTECH II program.
- 15 February 2016
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 682, 61-68
New Aluminum Base Materials for Use on Electrical Purposes
Modern power industry expects new, dedicated aluminum based alloys with non-standard properties, including increased resistance to temperature. Materials exhibiting higher thermal resistance allow to increase operating temperature of electrical conductors, which results in the increase of their current carrying capacity. Commonly known and used in such applications are alloys from the AlZr group. Despite their advantages scientists from around the world are searching for new alternatives. In this paper authors present research results on Al-Mo and Al-Ag alloys with particular interest to the analysis of the molybdenum addition to the aluminum in the amount of 0.05, 0.1, 0.2% and silver addition in the amount of 0.05, 0.1, 0.15% by mass on the mechanical and electrical properties of obtained alloys. Tests were also carried out for reference material which is high-purity aluminum and the AlZr alloy, both in the as cast state temper. Results showed a significant change of temperature coefficient of resistance in Al-Ag alloys compared to Al, which leads to possible increase of the Joule’a heat without the raise of conductors temperature limit. On the other hand, above-average heat resistance of alloys from the Al-Mo group of materials was achieved during the trials. On that basis authors state that Al-Ag alloys may be used for the production of ACSS conductors and Al-Mo alloys for TACSR or TACIR type of conductors.This study was performed under a project financed by NCBiR within the INNOTECH II program.