Aljoscha Sander
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Aljoscha Sander has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Andreas Florian Haselsteiner
University of Bremen BIK -Institute for Integrated Product Development 28359 Bremen Germany
4 shared publications - Klaus-Dieter Thoben
University of Bremen
4 shared publications - Jan-Hendrik Ohlendorf
Faculty of Production Engineering University of Bremen BIK -Institute for Integrated Product Development 28359 Bremen Germany
3 shared publications - Ed Mackay
University of Exeter UK
2 shared publications - Stephan Oelker
BIBA – Bremer Institut für Produktion und Logistik GmbH at the University of Bremen
2 shared publications - Abderrahim Ait-Alla
University of Bremen
1 shared publication
Latest Publications
- 1 January 2022
- Published by Elsevier in Renewable Energy
- Vol. 181, 945-965
Long-term extreme response of an offshore turbine: How accurate are contour-based estimates?
- 1 January 2022
- Published by Elsevier in Renewable Energy
- Vol. 181, 945-965
Long-term extreme response of an offshore turbine: How accurate are contour-based estimates?
- Open Access
- 1 September 2021
- Published by Elsevier in Ocean Engineering
- Vol. 236
A benchmarking exercise for environmental contours
- 1 September 2021
- Published by Elsevier in Ocean Engineering
- Vol. 236
Open AccessA benchmarking exercise for environmental contours
- Open Access
- 16 July 2021
- Published by ASME International
Global Hierarchical Models for Wind and Wave Contours: Physical Interpretations of the Dependence Functions
Applications such as the design of offshore wind turbines require the estimation of the joint distributions of variables like wind speed, wave height and wave period. The joint distribution can then be used, for example, to define design load cases using the environmental contour method. Often the joint distribution is described using so-called global hierarchical models. In these
- 16 July 2021
- Published by ASME International
Open AccessGlobal Hierarchical Models for Wind and Wave Contours: Physical Interpretations of the Dependence Functions
Applications such as the design of offshore wind turbines require the estimation of the joint distributions of variables like wind speed, wave height and wave period. The joint distribution can then be used, for example, to define design load cases using the environmental contour method. Often the joint distribution is described using so-called global hierarchical models. In these
- Open Access
- 16 July 2021
- Published by ASME International
Relative Motion During Single Blade Installation: Measurements From the North Sea
During single blade Installation in offshore wind parks, relative motion between nacelle and blade root due to wind and wave excitation pose a significant challenge. While wave excitation can be modelled considerably well by employing state of the art simulation tools and can, therefore, be included in installation planning, other phenomena such as vortex-induced vibrations and
- 16 July 2021
- Published by ASME International
Open AccessRelative Motion During Single Blade Installation: Measurements From the North Sea
During single blade Installation in offshore wind parks, relative motion between nacelle and blade root due to wind and wave excitation pose a significant challenge. While wave excitation can be modelled considerably well by employing state of the art simulation tools and can, therefore, be included in installation planning, other phenomena such as vortex-induced vibrations and
- Open Access
Evaluation of the Impact of Weather-Related Limitations on the Installation of Offshore Wind Turbine Towers
Weather conditions have a significant impact on the installation of offshore wind turbines. The rules for installation set clear limits. These limits are usually based on estimations of various experts and not on real assumptions and measurements on-site. When wind speeds and wave heights are too high, work cannot be carried out, and this leads to delays and additional costs. Therefore, we have carried out a measurement campaign during the installation of rotor blades to investigate to which extent the limits can be adjusted by using a tuned mass damper. The results from the measurement campaign—specifically empirically derived significant wave height limits—are used in a discrete event simulation. This study simulates delays resulting from weather conditions. Based on this, the total installation costs are considered. The results of the measurement campaign show that a safe installation with the use of a damper is possible at wave heights of up to 1.6 m. With the discrete event simulation, it is possible to prove that 17.9% can be saved for the costs of the installation vessel. In addition, the wind farm could be erected 32 days faster. Thus, it can be stated that the use of a tuned mass damper simplifies the installation from a technical point of view and is economical.
Open AccessEvaluation of the Impact of Weather-Related Limitations on the Installation of Offshore Wind Turbine Towers
Weather conditions have a significant impact on the installation of offshore wind turbines. The rules for installation set clear limits. These limits are usually based on estimations of various experts and not on real assumptions and measurements on-site. When wind speeds and wave heights are too high, work cannot be carried out, and this leads to delays and additional costs. Therefore, we have carried out a measurement campaign during the installation of rotor blades to investigate to which extent the limits can be adjusted by using a tuned mass damper. The results from the measurement campaign—specifically empirically derived significant wave height limits—are used in a discrete event simulation. This study simulates delays resulting from weather conditions. Based on this, the total installation costs are considered. The results of the measurement campaign show that a safe installation with the use of a damper is possible at wave heights of up to 1.6 m. With the discrete event simulation, it is possible to prove that 17.9% can be saved for the costs of the installation vessel. In addition, the wind farm could be erected 32 days faster. Thus, it can be stated that the use of a tuned mass damper simplifies the installation from a technical point of view and is economical.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
AUVx — A novel miniaturized autonomous underwater vehicle
Wiihìn the 3 year project DAEDALUS the battery powered underwater vehicle AUV x was developed at DFKI. This autonomous underwater vehicle (AUV) is a novel, miniaturized exploration and research vehicle (see Fig. 1). The AUV x can be operated both autonomous or remotely as a hybrid ROV with a near field optical communication modem or a copper wire cable. What makes this paper unique is that it describes the development of a system which has a high degree of miniaturization and the feature richness of much bigger systems: A complex heterogeneous processing architecture, sensor fusion of inertial data, a mathematical model of the robot and visual data which improves the AUVs pose and orientation estimation, a unique propulsion concept and the possibility to hover statically in the water column. Results of the design and build process with a strong focus on the CFD analysis and the evaluated model are presented. The system was successfully tested in water basins at DFKI.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
AUVx — A novel miniaturized autonomous underwater vehicle
Wiihìn the 3 year project DAEDALUS the battery powered underwater vehicle AUV x was developed at DFKI. This autonomous underwater vehicle (AUV) is a novel, miniaturized exploration and research vehicle (see Fig. 1). The AUV x can be operated both autonomous or remotely as a hybrid ROV with a near field optical communication modem or a copper wire cable. What makes this paper unique is that it describes the development of a system which has a high degree of miniaturization and the feature richness of much bigger systems: A complex heterogeneous processing architecture, sensor fusion of inertial data, a mathematical model of the robot and visual data which improves the AUVs pose and orientation estimation, a unique propulsion concept and the possibility to hover statically in the water column. Results of the design and build process with a strong focus on the CFD analysis and the evaluated model are presented. The system was successfully tested in water basins at DFKI.