Alejandro Espinel Hernández
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Alejandro Espinel Hernández has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Angel Sánchez Roca
University of Oriente
5 shared publications - Hipólito Carvajal Fals
Faculty of Mechanical Engineering, University of Campinas, UNICAMP, Campinas, Brazil
5 shared publications - Louriel Oliveira Vilarinho
Faculty of Mechanical Engineering, Federal University of Uberlândia, Uberlândia, Brazil
3 shared publications - Mario César Sánchez Orozco
Univeridad de Oriente
3 shared publications - Dayana Palma
Universidad de Valparaíso
2 shared publications - Ramón Arias Gilart
Centro de Biotecnología Dr. Daniel Alkalay Lowitt (CBDAL), Departamento de Biotecnología y Bioingeniería, Universidad Técnica Federico Santa María, Avenida España 1680, Valparaíso 2390123, Chile
2 shared publications
Latest Publications
- Open Access
- 29 December 2023
- Published by Pantanal Editora in Trends in Agricultural and Environmental Sciences
- p. e230008
Pore Segmentation in Industrial Radiographic Images Using Adaptive Thresholding and Morphological Analysis
This study presents an innovative approach to segmenting pores in low-quality industrial radiographic images using advanced image processing and adaptive segmentation techniques. The process involves several steps, including conversion of the image to grayscale to simplify analysis. Gaussian and median filters are then applied to improve image quality and enable more accurate segmentation. The methodology is based on adaptive thresholding and edge detection using the Canny algorithm, achieving accurate pore area measurements, even for those unnoticed by experts, with measurement errors of less than 0.1 mm². This high accuracy supports the method's effectiveness in pore detection and measurement. The resulting tool has great potential in industrial radiography applications, from quality control to defect analysis. While recognizing the need for continued research to improve contrast and illumination, as well as to address potential sources of error, these refinements promise to further elevate an already reliable and accurate method with a wide reach in the industry.
- 29 December 2023
- Published by Pantanal Editora in Trends in Agricultural and Environmental Sciences
- p. e230008
Open AccessPore Segmentation in Industrial Radiographic Images Using Adaptive Thresholding and Morphological Analysis
This study presents an innovative approach to segmenting pores in low-quality industrial radiographic images using advanced image processing and adaptive segmentation techniques. The process involves several steps, including conversion of the image to grayscale to simplify analysis. Gaussian and median filters are then applied to improve image quality and enable more accurate segmentation. The methodology is based on adaptive thresholding and edge detection using the Canny algorithm, achieving accurate pore area measurements, even for those unnoticed by experts, with measurement errors of less than 0.1 mm². This high accuracy supports the method's effectiveness in pore detection and measurement. The resulting tool has great potential in industrial radiography applications, from quality control to defect analysis. While recognizing the need for continued research to improve contrast and illumination, as well as to address potential sources of error, these refinements promise to further elevate an already reliable and accurate method with a wide reach in the industry.
- Open Access
- 23 March 2022
- Published by Universidad Nacional de Colombia in DYNA
- Vol. 89 (220) , 121-129
Influence of zinc coating on nugget development and mechanical properties in dissimilar welded joints DP600 – AISI304 obtained by the RSW process
This paper researches the influence of zinc coating of galvanized DP600 steel (DP600G) on the nugget development and mechanical properties of dissimilar DP600 - AISI304 welded joints obtained by resistance spot welding process (RSW). The RSW evaluations consisted of determining, from the dynamic resistance curves, the different stages involved in nugget formation. The experimental results showed that the zinc coating on the DP600G steel has a significant influence on the time needed for the start of the nugget formation, two times higher than that used for non-galvanized steel. The expulsion time was delayed by 1.12 times. The presence of Zn in the DP600G/AISI304 welded joints produced smaller nugget diameters compared to the DP600/AISI304 joints for the same experimental conditions, however higher peak failure load values were obtained for the first. The causes of this unusual behavior are also analyzed in this paper.
- 23 March 2022
- Published by Universidad Nacional de Colombia in DYNA
- Vol. 89 (220) , 121-129
Open AccessInfluence of zinc coating on nugget development and mechanical properties in dissimilar welded joints DP600 – AISI304 obtained by the RSW process
This paper researches the influence of zinc coating of galvanized DP600 steel (DP600G) on the nugget development and mechanical properties of dissimilar DP600 - AISI304 welded joints obtained by resistance spot welding process (RSW). The RSW evaluations consisted of determining, from the dynamic resistance curves, the different stages involved in nugget formation. The experimental results showed that the zinc coating on the DP600G steel has a significant influence on the time needed for the start of the nugget formation, two times higher than that used for non-galvanized steel. The expulsion time was delayed by 1.12 times. The presence of Zn in the DP600G/AISI304 welded joints produced smaller nugget diameters compared to the DP600/AISI304 joints for the same experimental conditions, however higher peak failure load values were obtained for the first. The causes of this unusual behavior are also analyzed in this paper.
- 17 February 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (3-4) , 1877-1887
Effect of zinc coating on delay nugget formation in dissimilar DP600-AISI304 welded joints obtained by the resistance spot welding process
- 17 February 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (3-4) , 1877-1887
Effect of zinc coating on delay nugget formation in dissimilar DP600-AISI304 welded joints obtained by the resistance spot welding process
- 18 May 2016
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 21 (8) , 607-613
Influence of polarity on mechanical properties of dissimilar resistance spot welds of DP 600/AISI 304 steels
The influence of polarity during resistance spot weld (RSW) of dissimilar lap joints on mechanical properties and failure mode is assessed in this work. A dissimilar lap joint was set using DP 600 dual phase steel with AISI 304 stainless steel. The experiments were performed on a medium-frequency direct current spot welding machine with proper data acquisition of voltage and welding current. Temperature evolution was also acquired by using IR camera. The mechanical properties of spot welds were evaluated by using a coach peel testing. The effect of welding current and welding time on mechanical properties was also evaluated. Correlations between polarity with the welding nugget size, failure mode, tensile strength, temperature evolution and dynamic resistance were analysed. The analysis confirmed that the polarity on dissimilar lap joints affects the behaviour of dissimilar RSWs.
- 18 May 2016
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 21 (8) , 607-613
Influence of polarity on mechanical properties of dissimilar resistance spot welds of DP 600/AISI 304 steels
The influence of polarity during resistance spot weld (RSW) of dissimilar lap joints on mechanical properties and failure mode is assessed in this work. A dissimilar lap joint was set using DP 600 dual phase steel with AISI 304 stainless steel. The experiments were performed on a medium-frequency direct current spot welding machine with proper data acquisition of voltage and welding current. Temperature evolution was also acquired by using IR camera. The mechanical properties of spot welds were evaluated by using a coach peel testing. The effect of welding current and welding time on mechanical properties was also evaluated. Correlations between polarity with the welding nugget size, failure mode, tensile strength, temperature evolution and dynamic resistance were analysed. The analysis confirmed that the polarity on dissimilar lap joints affects the behaviour of dissimilar RSWs.