Nosaibeh Nosrati-Ghods
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Nosaibeh Nosrati-Ghods has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Bruno Merven
Energy Research Centre University of Cape Town Private Bag X3 Rondebosch 7701 South Africa
3 shared publications Eric van Steen
Department of Chemical Engineering, Faculty of Engineering and the Built Environment University of Cape Town Cape Town South Africa
3 shared publications- Harro von Blottnitz
University of Cape Town
3 shared publications Joseph Masenda
3 shared publications- Andrew Marquard2 shared publications
- Bosibori Mosongo
Department of Geography, STEER Centre, Loughborough University, Loughborough, United Kingdom
2 shared publications
Latest Publications
- Open Access
- 12 August 2026
- Published by Elsevier in Energy Conversion and Management
- Vol. 368
An exploration of transition pathways for South Africa’s coal-to-liquids complex under long-term national greenhouse gas emissions constraints
- 12 August 2026
- Published by Elsevier in Energy Conversion and Management
- Vol. 368
Open AccessAn exploration of transition pathways for South Africa’s coal-to-liquids complex under long-term national greenhouse gas emissions constraints
- Open Access
- 13 February 2026
- Published by Elsevier in SSRN Electronic Journal
An exploration of transition pathways for South Africa’s coal-to-liquids complex under long-term national greenhouse gas emissions constraints
Coal-to-liquids (CtL) industries represent a critical challenge for long-term energy transitions, combining high greenhouse-gas emissions with strong economic and energy-security roles. South Africa’s Secunda CtL complex—responsible for around 12% of national emissions—illustrates these tensions, where rapid or unplanned shutdown could impose substantial economic and energy-security risks. This study evaluates alternative decarbonisation strategies and transition pathways for a CtL industry using a national energy-system optimisation framework (SATIM). Three pathways are examined: a Baseline; an incremental, roadmap-aligned pathway reflecting near-term efficiency and renewable integration measures; and a structural decarbonisation pathway in which low-carbon technologies are deployed under a national long-term emissions constraint (LTEC).The incremental scenario reduces facility-level emissions by ~26% by 2030, decreasing carbon intensity from 180 to 147 kt CO₂/PJ. Structural decarbonisation under a national Long-Term Emissions Constraint (LTEC) of 8.5 Gt achieves deeper cuts—45% by 2030, 56% by 2040, and 62% by 2045—lowering carbon intensity to 97 kt CO₂/PJ. While a structural transition is feasible, decarbonisation remains partial due to limited CO₂ availability and high transport, storage, and DAC costs. Demand-side electrification and EV uptake ease fuel demand and CO₂ constraints, while transition timing is primarily governed by renewable-energy costs, policy ambition (e.g., tighter LTEC, carbon taxes), and oil-price dynamics. Lower oil prices narrow profit margins and reduce Fischer–Tropsch output and Scope 1 emissions, while accelerating low-carbon technologies and earlier RWGS deployment despite lower FT profitability. The findings provide strategic insights for policymakers and planners designing industrial transition pathways in carbon-intensive economies.
- 13 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAn exploration of transition pathways for South Africa’s coal-to-liquids complex under long-term national greenhouse gas emissions constraints
Coal-to-liquids (CtL) industries represent a critical challenge for long-term energy transitions, combining high greenhouse-gas emissions with strong economic and energy-security roles. South Africa’s Secunda CtL complex—responsible for around 12% of national emissions—illustrates these tensions, where rapid or unplanned shutdown could impose substantial economic and energy-security risks. This study evaluates alternative decarbonisation strategies and transition pathways for a CtL industry using a national energy-system optimisation framework (SATIM). Three pathways are examined: a Baseline; an incremental, roadmap-aligned pathway reflecting near-term efficiency and renewable integration measures; and a structural decarbonisation pathway in which low-carbon technologies are deployed under a national long-term emissions constraint (LTEC).The incremental scenario reduces facility-level emissions by ~26% by 2030, decreasing carbon intensity from 180 to 147 kt CO₂/PJ. Structural decarbonisation under a national Long-Term Emissions Constraint (LTEC) of 8.5 Gt achieves deeper cuts—45% by 2030, 56% by 2040, and 62% by 2045—lowering carbon intensity to 97 kt CO₂/PJ. While a structural transition is feasible, decarbonisation remains partial due to limited CO₂ availability and high transport, storage, and DAC costs. Demand-side electrification and EV uptake ease fuel demand and CO₂ constraints, while transition timing is primarily governed by renewable-energy costs, policy ambition (e.g., tighter LTEC, carbon taxes), and oil-price dynamics. Lower oil prices narrow profit margins and reduce Fischer–Tropsch output and Scope 1 emissions, while accelerating low-carbon technologies and earlier RWGS deployment despite lower FT profitability. The findings provide strategic insights for policymakers and planners designing industrial transition pathways in carbon-intensive economies.
- Open Access
- 7 February 2026
- Published by Elsevier in SSRN Electronic Journal
Industrial decarbonisation under cumulative carbon constraints: Energy system responses of a coal-to-liquids facility
The coal-to-liquids (CtL) complex in Secunda, South Africa—responsible for 12% of national GHG emissions—is a globally unique coal-based producer of liquid fuels and chemicals. Mitigating these emissions is important for long-term energy system transitions, yet a rapid/unplanned shutdown would impose major economic and energy-security risks. Using the South African TIMES (SATIM) energy-system model, this study evaluates techno-economic pathways under three scenarios: a Baseline (business-as-usual); an incremental Roadmap-Aligned scenario reflecting Sasol’s 2030 decarbonisation plan; and a transformative Structural Decarbonisation scenario in which low-carbon technologies are selected under cumulative emissions constraints.The incremental scenario reduces facility-level emissions by ~26% by 2030, decreasing carbon intensity from 180 to 147 kt CO₂/PJ. Structural decarbonisation under a national Long-Term Emissions Constraint (LTEC) of 8.5 Gt achieves deeper cuts—45% by 2030, 56% by 2040, and 62% by 2045—lowering carbon intensity to 97 kt CO₂/PJ. With declining oil prices, Fischer–Tropsch output and Scope 1 emissions drop more sharply, with earlier RWGS deployment despite reduced FT profitability.While a structural transition is feasible, decarbonisation remains partial due to limited CO₂ availability and high transport, storage, and DAC costs. Demand-side shifts, including EV adoption and electrification, reduce fuel demand, partially alleviating CO₂ availability constraints. Transition timing and efficiency are largely governed by low-cost green energy availability and policy ambition strength (e.g., tighter LTEC, carbon taxes). Lower oil prices narrow profit margins but accelerate low-carbon technologies. A gradual, phased transition can balance climate mitigation targets, energy security and economic stability, enabling a sustainable, resilient energy system.
- 7 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessIndustrial decarbonisation under cumulative carbon constraints: Energy system responses of a coal-to-liquids facility
The coal-to-liquids (CtL) complex in Secunda, South Africa—responsible for 12% of national GHG emissions—is a globally unique coal-based producer of liquid fuels and chemicals. Mitigating these emissions is important for long-term energy system transitions, yet a rapid/unplanned shutdown would impose major economic and energy-security risks. Using the South African TIMES (SATIM) energy-system model, this study evaluates techno-economic pathways under three scenarios: a Baseline (business-as-usual); an incremental Roadmap-Aligned scenario reflecting Sasol’s 2030 decarbonisation plan; and a transformative Structural Decarbonisation scenario in which low-carbon technologies are selected under cumulative emissions constraints.The incremental scenario reduces facility-level emissions by ~26% by 2030, decreasing carbon intensity from 180 to 147 kt CO₂/PJ. Structural decarbonisation under a national Long-Term Emissions Constraint (LTEC) of 8.5 Gt achieves deeper cuts—45% by 2030, 56% by 2040, and 62% by 2045—lowering carbon intensity to 97 kt CO₂/PJ. With declining oil prices, Fischer–Tropsch output and Scope 1 emissions drop more sharply, with earlier RWGS deployment despite reduced FT profitability.While a structural transition is feasible, decarbonisation remains partial due to limited CO₂ availability and high transport, storage, and DAC costs. Demand-side shifts, including EV adoption and electrification, reduce fuel demand, partially alleviating CO₂ availability constraints. Transition timing and efficiency are largely governed by low-cost green energy availability and policy ambition strength (e.g., tighter LTEC, carbon taxes). Lower oil prices narrow profit margins but accelerate low-carbon technologies. A gradual, phased transition can balance climate mitigation targets, energy security and economic stability, enabling a sustainable, resilient energy system.
- Open Access
- 27 January 2026
- Published by Wiley in Photochemistry and Photobiology
- Vol. 102 (5) , 1220-1233
Immobilized CuCl 2 / TiO 2 photocatalysts for the selective oxidation of benzyl alcohol to benzaldehyde
The oxidation of alcohols to aldehydes is a key transformation in industrial chemistry, as aldehydes are vital intermediates in the synthesis of pharmaceuticals and fine chemicals. Conventional oxidation routes typically employ stoichiometric and corrosive oxidants, generating significant environmental concerns. Greener oxidants such as molecular oxygen (O 2 ) offer a more sustainable alternative to stoichiometric oxidants; however, their efficient utilization requires activation by catalysts (e.g., Cu‐, Pd‐, Au‐, or Ti‐based systems). Homogeneous photocatalysts such as CuCl 2 exhibit promising activity under light irradiation but are limited by challenges in separation and recycling. This study investigates the immobilization of CuCl 2 and TiO 2 (P25) within sodium alginate beads to facilitate photocatalyst recovery and minimize metal leaching. Under UV irradiation for 4 h, benzyl alcohol conversions of 54% (P25) and 49% (CuCl 2 ) were achieved. Catalyst encapsulation markedly reduced activity due to internal mass transport limitations, as restricted diffusion of O 2 and benzyl alcohol within the bead matrix limited access to active sites and suppressed overall reaction rates. Co‐immobilization of P25 and CuCl 2 partially restored conversion (22%), while maintaining high benzaldehyde selectivity (≈1 after 4 h) across all systems. These findings highlight oxygen depletion and mass transfer resistance as key constraints in bead‐based photocatalysts. To guide further optimization, a MATLAB‐based reactor model incorporating species transport, interfacial mass transfer, and kinetics was developed.
- 27 January 2026
- Published by Wiley in Photochemistry and Photobiology
- Vol. 102 (5) , 1220-1233
Open AccessImmobilized CuCl 2 / TiO 2 photocatalysts for the selective oxidation of benzyl alcohol to benzaldehyde
The oxidation of alcohols to aldehydes is a key transformation in industrial chemistry, as aldehydes are vital intermediates in the synthesis of pharmaceuticals and fine chemicals. Conventional oxidation routes typically employ stoichiometric and corrosive oxidants, generating significant environmental concerns. Greener oxidants such as molecular oxygen (O 2 ) offer a more sustainable alternative to stoichiometric oxidants; however, their efficient utilization requires activation by catalysts (e.g., Cu‐, Pd‐, Au‐, or Ti‐based systems). Homogeneous photocatalysts such as CuCl 2 exhibit promising activity under light irradiation but are limited by challenges in separation and recycling. This study investigates the immobilization of CuCl 2 and TiO 2 (P25) within sodium alginate beads to facilitate photocatalyst recovery and minimize metal leaching. Under UV irradiation for 4 h, benzyl alcohol conversions of 54% (P25) and 49% (CuCl 2 ) were achieved. Catalyst encapsulation markedly reduced activity due to internal mass transport limitations, as restricted diffusion of O 2 and benzyl alcohol within the bead matrix limited access to active sites and suppressed overall reaction rates. Co‐immobilization of P25 and CuCl 2 partially restored conversion (22%), while maintaining high benzaldehyde selectivity (≈1 after 4 h) across all systems. These findings highlight oxygen depletion and mass transfer resistance as key constraints in bead‐based photocatalysts. To guide further optimization, a MATLAB‐based reactor model incorporating species transport, interfacial mass transfer, and kinetics was developed.
- Open Access
- 3 October 2025
- Published by Springer Nature in Reaction Kinetics, Mechanisms and Catalysis
- Vol. 139 (1) , 869-895
Enhancing the selective conversion of alcohols to aldehydes using oxygen over heterogeneous photocatalysts — critical factors with emphasis on benzyl alcohol
Heterogeneous photocatalysis is an advanced oxidation technique widely explored for the selective conversion of benzyl alcohol (C 7 H 8 O) into benzaldehyde, an important intermediate in organic synthesis. This review critically examines the influence of key operational and morphological factors—including solvent choice, temperature, and light intensity—on photocatalytic performance. The synthesis method notably affects catalyst activity, with solvothermal preparation of TiO 2 significantly enhancing the reaction rate constant. Photo-deposition emerges as an effective alternative when both catalyst and support materials are available. Among various TiO 2 nanostructures (nanowires, nanotubes, nanofibers, nanosheets, and hollow nanospheres), hollow nanospheres exhibit superior photocatalytic activity due to improved light absorption and charge separation. Elevated light intensity and temperature further accelerate the reaction rate, resulting in higher rate constants. A range of catalysts—including C-ZnInS 4 , ZnInS 4 , Pt-TiO 2 , RuO 2 /TiO 2 nanobelts, 0.95Ru/3DOM BiVO 4 -Ar-300, Pt/Bi 2 MoO 6 -glycerol, Ni-OTO 2 , W 10 O 32 4− ,WO 3 (7.6)/TiO 2 , TiO 1.966 .N 0.034 , and Bi 2 WO 6 —demonstrate promising rate constants of 75.0, 53.75, 57, 46.0, 38.0, 34.0, 33.25, 29.6, 28.0, 27.0 and 22.25 g cat −1 h −1 for alcohol oxidation. Notably, TiO 2 N 0.034 and ZnIn 2 S 4 achieve 100% conversion with > 99% selectivity within 4 and 2 h, respectively, underscoring their excellent photocatalytic potential.
- 3 October 2025
- Published by Springer Nature in Reaction Kinetics, Mechanisms and Catalysis
- Vol. 139 (1) , 869-895
Open AccessEnhancing the selective conversion of alcohols to aldehydes using oxygen over heterogeneous photocatalysts — critical factors with emphasis on benzyl alcohol
Heterogeneous photocatalysis is an advanced oxidation technique widely explored for the selective conversion of benzyl alcohol (C 7 H 8 O) into benzaldehyde, an important intermediate in organic synthesis. This review critically examines the influence of key operational and morphological factors—including solvent choice, temperature, and light intensity—on photocatalytic performance. The synthesis method notably affects catalyst activity, with solvothermal preparation of TiO 2 significantly enhancing the reaction rate constant. Photo-deposition emerges as an effective alternative when both catalyst and support materials are available. Among various TiO 2 nanostructures (nanowires, nanotubes, nanofibers, nanosheets, and hollow nanospheres), hollow nanospheres exhibit superior photocatalytic activity due to improved light absorption and charge separation. Elevated light intensity and temperature further accelerate the reaction rate, resulting in higher rate constants. A range of catalysts—including C-ZnInS 4 , ZnInS 4 , Pt-TiO 2 , RuO 2 /TiO 2 nanobelts, 0.95Ru/3DOM BiVO 4 -Ar-300, Pt/Bi 2 MoO 6 -glycerol, Ni-OTO 2 , W 10 O 32 4− ,WO 3 (7.6)/TiO 2 , TiO 1.966 .N 0.034 , and Bi 2 WO 6 —demonstrate promising rate constants of 75.0, 53.75, 57, 46.0, 38.0, 34.0, 33.25, 29.6, 28.0, 27.0 and 22.25 g cat −1 h −1 for alcohol oxidation. Notably, TiO 2 N 0.034 and ZnIn 2 S 4 achieve 100% conversion with > 99% selectivity within 4 and 2 h, respectively, underscoring their excellent photocatalytic potential.
- Open Access
- 10 December 2024
- Published by Elsevier in Biochemical Engineering Journal
- Vol. 215
Techno-economic assessment of waste poly(lactic acid) enzymatic hydrolysis and recycling for poly(lactic acid) production
- 10 December 2024
- Published by Elsevier in Biochemical Engineering Journal
- Vol. 215
Open AccessTechno-economic assessment of waste poly(lactic acid) enzymatic hydrolysis and recycling for poly(lactic acid) production
- Open Access
- 5 October 2024
- Published by Elsevier in Data in Brief
- Vol. 57, 110999
An open and lite technoeconomic dataset and assumptions for open energy, emissions and mitigation modeling in the Republic of South Africa
- 5 October 2024
- Published by Elsevier in Data in Brief
- Vol. 57, 110999
Open AccessAn open and lite technoeconomic dataset and assumptions for open energy, emissions and mitigation modeling in the Republic of South Africa
- Open Access
- 30 September 2024
- Published by Cambridge University Press (CUP) in Cambridge Open Engage
Long-Term Forecasting: A MAED Application for Residential Water Heating in South Africa (2024–2040)
This article aims to provide an analysis of water heating within South Africa’s residential energy demand. With the Model for Analysis of Energy Demand (MAED) this work investigates four scenarios that account for varying degrees of governmental intervention and policy implementation, specifically in the context of the South African National Standards (SANS 10400-XA2). The three scenarios are designed to assess impacts on energy consumption, focusing primarily on the adoption of solar water heaters across different income groups from 2020 to 2040. The analysis reveals that solar thermal use, when coupled with effective policy support, can significantly mitigate the reliance on traditional, carbon-intensive fuels, particularly within low-to-middle-income households. Through the promotion of said solar water heaters and improved water access, living standards can be enhanced for vulnerable populations while simultaneously mitigating climate change effects. Findings also indicate that strong governmental support is essential for realizing significant energy savings and achieving equitable access to sustainable energy technologies. In the absence of such support, the anticipated benefits of energy efficiency improvements and emissions reductions may not be fully achieved. This is true particularly for low-to-middle-income households that are more likely to remain dependent on fuels with negative health and environmental implications.
- 30 September 2024
- Published by Cambridge University Press (CUP) in Cambridge Open Engage
Open AccessLong-Term Forecasting: A MAED Application for Residential Water Heating in South Africa (2024–2040)
This article aims to provide an analysis of water heating within South Africa’s residential energy demand. With the Model for Analysis of Energy Demand (MAED) this work investigates four scenarios that account for varying degrees of governmental intervention and policy implementation, specifically in the context of the South African National Standards (SANS 10400-XA2). The three scenarios are designed to assess impacts on energy consumption, focusing primarily on the adoption of solar water heaters across different income groups from 2020 to 2040. The analysis reveals that solar thermal use, when coupled with effective policy support, can significantly mitigate the reliance on traditional, carbon-intensive fuels, particularly within low-to-middle-income households. Through the promotion of said solar water heaters and improved water access, living standards can be enhanced for vulnerable populations while simultaneously mitigating climate change effects. Findings also indicate that strong governmental support is essential for realizing significant energy savings and achieving equitable access to sustainable energy technologies. In the absence of such support, the anticipated benefits of energy efficiency improvements and emissions reductions may not be fully achieved. This is true particularly for low-to-middle-income households that are more likely to remain dependent on fuels with negative health and environmental implications.
- 5 April 2024
- Published by Bentham Science Publishers Ltd. in Journal of Photocatalysis
- Vol. 04, 1-14
Kinetic Analysis of Solvent Effect in the Photocatalytic, Aerobic Oxidation of Benzyl Alcohol over P25
Background:: Photocatalysis is of particular importance in the oxidation of alcohols to aldehydes to increase the conversion of benzyl alcohol oxidation to benzaldehyde at high selectivity, which could be useful for the pharmaceutical and perfumery industries. Objective:: The oxidation of benzyl alcohol over P25 was investigated in various solvents (water, benzotrifluoride, toluene and acetonitrile) Methods:: The reaction was performed in an isothermal slurry batch reactor in the presence and absence of UV-light. The products were analysed using GC-FID; the deposits formed on the catalyst was analysed using TGA and FTIR. Results:: In the presence of light, the reaction was very selective for the formation of benzaldehyde (e.g., 99% selectivity at 53% conversion using acetonitrile as a solvent), whereas, in the absence of light, the formation of higher molecular weight products was observed (e.g., 22% selectivity at 1.7% conversion using acetonitrile as a solvent). It was observed that the activity in the absence of oxygen was initially high, but it dropped rapidly from initially 0.4 to 0 mmol g-1 h-1 after 2-4 h (using acetonitrile as a solvent). This was attributed to the activity of the few oxidized sites present on P25. Conclusion:: Acetonitrile appears to be the most effective solvent, as it seems to interact least with the catalytically active sites. The photocatalytic oxidation of benzyl alcohol over P25 does not only yield products in the solution, but also deposits on the surface. The deposits can be removed in an oxidative environment or an inert environment.
- 5 April 2024
- Published by Bentham Science Publishers Ltd. in Journal of Photocatalysis
- Vol. 04, 1-14
Kinetic Analysis of Solvent Effect in the Photocatalytic, Aerobic Oxidation of Benzyl Alcohol over P25
Background:: Photocatalysis is of particular importance in the oxidation of alcohols to aldehydes to increase the conversion of benzyl alcohol oxidation to benzaldehyde at high selectivity, which could be useful for the pharmaceutical and perfumery industries. Objective:: The oxidation of benzyl alcohol over P25 was investigated in various solvents (water, benzotrifluoride, toluene and acetonitrile) Methods:: The reaction was performed in an isothermal slurry batch reactor in the presence and absence of UV-light. The products were analysed using GC-FID; the deposits formed on the catalyst was analysed using TGA and FTIR. Results:: In the presence of light, the reaction was very selective for the formation of benzaldehyde (e.g., 99% selectivity at 53% conversion using acetonitrile as a solvent), whereas, in the absence of light, the formation of higher molecular weight products was observed (e.g., 22% selectivity at 1.7% conversion using acetonitrile as a solvent). It was observed that the activity in the absence of oxygen was initially high, but it dropped rapidly from initially 0.4 to 0 mmol g-1 h-1 after 2-4 h (using acetonitrile as a solvent). This was attributed to the activity of the few oxidized sites present on P25. Conclusion:: Acetonitrile appears to be the most effective solvent, as it seems to interact least with the catalytically active sites. The photocatalytic oxidation of benzyl alcohol over P25 does not only yield products in the solution, but also deposits on the surface. The deposits can be removed in an oxidative environment or an inert environment.
- 1 December 2020
- Published by Elsevier in Biochemical Engineering Journal
- Vol. 164, 107754
Analysis of ethanol production from xylose using Pichia stipitis in microaerobic conditions through experimental observations and kinetic modelling
- 1 December 2020
- Published by Elsevier in Biochemical Engineering Journal
- Vol. 164, 107754
Analysis of ethanol production from xylose using Pichia stipitis in microaerobic conditions through experimental observations and kinetic modelling