Irina Tazhibayeva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Irina Tazhibayeva has a total of 198 co-authors. Here are the top co-authors by number of shared publications:
- Timur Kulsartov
Institute of Nuclear Physics; Al-Farabi Kazakh National University
25 shared publications - Yuriy Ponkratov
Institute of Atomic Energy Branch RSE NNC RK, Kurchatov, Kazakhstan
21 shared publications - Yuriy Gordienko
Institute of Atomic Energy Branch of the National Nuclear Center of the Republic of Kazakhstan
18 shared publications - Zhanna Zaurbekova
Institute of Applied Sciences and Information Technologies, Almaty 050032, Kazakhstan
17 shared publications - Alexey V. Vertkov
JSC Red Star, Moscow, Russia
12 shared publications - Yevgen Chikhray
Candidate of Technical Sciences, Senior Researcher, Institute of Experimental and Theoretical Physics, al-Farabi Kazakh National University, Almaty, Kazakhstan
12 shared publications
Latest Publications
- 1 December 2025
- Published by Pleiades Publishing Ltd in Physics of Atomic Nuclei
- Vol. 88 (S2) , S186-S194
Diagnostics of Long-Term Erosion and Deposition of the Material of the First Wall in the KTM Tokamak: Testing and First Results
A diagnostic method for material transport (erosion and deposition) in the KTM tokamak vessel has been developed and tested for durations comparable to an experimental campaign. It is based on witness samples mounted in the tiles of the first wall of the tokamak vacuum vessel. It was found that the regions of greatest wall erosion are located near the equatorial plane and on the inner side of the upper dome. Deposition zones were identified on the outer periphery on the lower side of the chamber. Possible effects of conditioning and operational discharges on wall sputtering were considered.
- 1 December 2025
- Published by Pleiades Publishing Ltd in Physics of Atomic Nuclei
- Vol. 88 (S2) , S186-S194
Diagnostics of Long-Term Erosion and Deposition of the Material of the First Wall in the KTM Tokamak: Testing and First Results
A diagnostic method for material transport (erosion and deposition) in the KTM tokamak vessel has been developed and tested for durations comparable to an experimental campaign. It is based on witness samples mounted in the tiles of the first wall of the tokamak vacuum vessel. It was found that the regions of greatest wall erosion are located near the equatorial plane and on the inner side of the upper dome. Deposition zones were identified on the outer periphery on the lower side of the chamber. Possible effects of conditioning and operational discharges on wall sputtering were considered.
- 1 November 2024
- Published by Springer Nature in Atomic Energy
- Vol. 137 (1-2) , 121-128
Regulatory aspects and practice of radioactive waste management in the Republic of Kazakhstan
- 1 November 2024
- Published by Springer Nature in Atomic Energy
- Vol. 137 (1-2) , 121-128
Regulatory aspects and practice of radioactive waste management in the Republic of Kazakhstan
- 1 December 2023
- Published by Pleiades Publishing Ltd in Physics of Atomic Nuclei
- Vol. 86 (7) , 1663-1666
Comparison of Operating Parameters of the KTM Tokamak with Operating Ranges of the Facility
This article presents estimates of the operating region of the KTM tokamak in terms of plasma density and current for ohmic regimes on the basis of machine design parameters. The discharge parameters obtained in the experiments in 2021 are plotted on the diagram (ne, Ip). The increase in operating values of plasma current and achievement of boundary values of stability factor q ~ 4 are mentioned. It has been demonstrated that progressing into the region of higher plasma currents in the implemented density range leads to achievement of the limit in development of beams of accelerated electrons. Accordingly, the increase in operating plasma density is one of the aims of the next experimental campaign at the KTM tokamak.
- 1 December 2023
- Published by Pleiades Publishing Ltd in Physics of Atomic Nuclei
- Vol. 86 (7) , 1663-1666
Comparison of Operating Parameters of the KTM Tokamak with Operating Ranges of the Facility
This article presents estimates of the operating region of the KTM tokamak in terms of plasma density and current for ohmic regimes on the basis of machine design parameters. The discharge parameters obtained in the experiments in 2021 are plotted on the diagram (ne, Ip). The increase in operating values of plasma current and achievement of boundary values of stability factor q ~ 4 are mentioned. It has been demonstrated that progressing into the region of higher plasma currents in the implemented density range leads to achievement of the limit in development of beams of accelerated electrons. Accordingly, the increase in operating plasma density is one of the aims of the next experimental campaign at the KTM tokamak.
- 29 December 2021
- Published by Pleiades Publishing Ltd in Physics of Atomic Nuclei
- Vol. 84 (7) , 1245-1251
Stationary Operated Lithium In-Vessel Elements of a Tokamak
The concept of plasma facing elements (PFE) of a stationary fusion tokamak reactor based on the use of stagnant or slow-flowing liquid lithium enclosed in a capillary-porous structure which allows integrating the advantages of liquid metal with the possibility of its uniform distribution over the surface and ensuring a high stability under the influence of magnetohydrodynamic forces is considered in this study. Heat removal is provided by thermal conductivity through the PFE structure to the coolant. Development of the PFE design includes the creation and testing of a series of models of experimental devices such as a limiter and a divertor target with external systems of lithium refilling/change and heat removal designed for research in modeling conditions of bench installations and the T-11M tokamak. The paper presents the design and main parameters of such devices.
- 29 December 2021
- Published by Pleiades Publishing Ltd in Physics of Atomic Nuclei
- Vol. 84 (7) , 1245-1251
Stationary Operated Lithium In-Vessel Elements of a Tokamak
The concept of plasma facing elements (PFE) of a stationary fusion tokamak reactor based on the use of stagnant or slow-flowing liquid lithium enclosed in a capillary-porous structure which allows integrating the advantages of liquid metal with the possibility of its uniform distribution over the surface and ensuring a high stability under the influence of magnetohydrodynamic forces is considered in this study. Heat removal is provided by thermal conductivity through the PFE structure to the coolant. Development of the PFE design includes the creation and testing of a series of models of experimental devices such as a limiter and a divertor target with external systems of lithium refilling/change and heat removal designed for research in modeling conditions of bench installations and the T-11M tokamak. The paper presents the design and main parameters of such devices.
- 1 December 2020
- Published by Pleiades Publishing Ltd in Physics of Atomic Nuclei
- Vol. 83 (7) , 1116-1123
New Version of the KTM Lithium Divertor
At present, the Kazakhstan Tokamak for Material testing (KTM) project is in progress. The optimization of innovative design elements of the divertor is carried out at the KTM, in addition to studying materials applied for fusion technologies. The design of the lithium divertor module based on lithium capillary porous systems has been developed and tested successfully in real tokamak conditions. In this design, the problem of removing high-density heat flows is solved by using liquid metal coolant based on the Na–K eutectic alloy. The requirements for the improved safety and the divertor design compatibility with other in-vessel water-cooled elements of the tokamak and temperature limitation of the receiving lithium surface to the level 2 stipulated a new design solution of the divertor experimental module and the use of a totally new coolant—water flow dispersed with gas (gas-water spray). In the paper, the design solutions of the new version of the module, the coolant parameters, and the cooling system layout are described and substantiated. The experimental results on determining the heat transfer coefficient of the coolant based on gas-water spray are considered.
- 1 December 2020
- Published by Pleiades Publishing Ltd in Physics of Atomic Nuclei
- Vol. 83 (7) , 1116-1123
New Version of the KTM Lithium Divertor
At present, the Kazakhstan Tokamak for Material testing (KTM) project is in progress. The optimization of innovative design elements of the divertor is carried out at the KTM, in addition to studying materials applied for fusion technologies. The design of the lithium divertor module based on lithium capillary porous systems has been developed and tested successfully in real tokamak conditions. In this design, the problem of removing high-density heat flows is solved by using liquid metal coolant based on the Na–K eutectic alloy. The requirements for the improved safety and the divertor design compatibility with other in-vessel water-cooled elements of the tokamak and temperature limitation of the receiving lithium surface to the level 2 stipulated a new design solution of the divertor experimental module and the use of a totally new coolant—water flow dispersed with gas (gas-water spray). In the paper, the design solutions of the new version of the module, the coolant parameters, and the cooling system layout are described and substantiated. The experimental results on determining the heat transfer coefficient of the coolant based on gas-water spray are considered.
- Open Access
- 1 January 2020
- Published by NRC Kurchatov Institute in Problems of Atomic Science and Technology, Ser. Thermonuclear Fusion
- Vol. 43 (1) , 55-63
STATIONARY OPERATED LITHIUM IN-VESSEL ELEMENTS OF A TOKAMAK
- 1 January 2020
- Published by NRC Kurchatov Institute in Problems of Atomic Science and Technology, Ser. Thermonuclear Fusion
- Vol. 43 (1) , 55-63
Open AccessSTATIONARY OPERATED LITHIUM IN-VESSEL ELEMENTS OF A TOKAMAK
- 1 December 2019
- Published by Pleiades Publishing Ltd in Physics of Atomic Nuclei
- Vol. 82 (7) , 1038-1047
The Electrotechnical Complex of the KTM Tokamak Pulsed Power Supply System
The pulsed power supply equipment belongs to the basic technological systems intended for implementing the required scenarios of changing currents in magnetic coils. The accuracy of implementing these scenarios directly determines the possibility of attaining the plasma breakdown and the required ultimate plasma parameters. Given the uniqueness of each facility under construction in the world and the installed capacity of the electrotechnical equipment applied in the power supply configuration, one can state with confidence that the construction of similar power supply complexes and their control systems, the optimization of their electrotechnical parameters, and the subsequent accident-free operation are vital tasks in mastering controlled thermonuclear fusion technologies. This paper describes the pulsed power supply system of the KTM tokamak (Kazakhstan) designed for material testing, the digital control system for its power conversion equipment, electrotechnical solutions adopted in the design of the KTM tokamak pulsed power supply system, and findings of tests of some items of equipment and their components. The tests have demonstrated sufficient efficiency of the adopted electrotechnical solutions and the possibility of applying them to implement the pulsed power supply systems for small and medium sized tokamaks.
- 1 December 2019
- Published by Pleiades Publishing Ltd in Physics of Atomic Nuclei
- Vol. 82 (7) , 1038-1047
The Electrotechnical Complex of the KTM Tokamak Pulsed Power Supply System
The pulsed power supply equipment belongs to the basic technological systems intended for implementing the required scenarios of changing currents in magnetic coils. The accuracy of implementing these scenarios directly determines the possibility of attaining the plasma breakdown and the required ultimate plasma parameters. Given the uniqueness of each facility under construction in the world and the installed capacity of the electrotechnical equipment applied in the power supply configuration, one can state with confidence that the construction of similar power supply complexes and their control systems, the optimization of their electrotechnical parameters, and the subsequent accident-free operation are vital tasks in mastering controlled thermonuclear fusion technologies. This paper describes the pulsed power supply system of the KTM tokamak (Kazakhstan) designed for material testing, the digital control system for its power conversion equipment, electrotechnical solutions adopted in the design of the KTM tokamak pulsed power supply system, and findings of tests of some items of equipment and their components. The tests have demonstrated sufficient efficiency of the adopted electrotechnical solutions and the possibility of applying them to implement the pulsed power supply systems for small and medium sized tokamaks.
- Open Access
- 1 November 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1370 (1)
Lithium divertor of KTM tokamak
At present time the project of Kazakh material science tokamak KTM is under implementation. In addition to solving problems in the study of materials for fusion technologies on tokamak is working out innovative design elements of the divertor. The design of the lithium divertor module based on lithium capillary-porous systems has been developed and successfully tested under real tokamak conditions. In this design, the solution to the problem of removal of heat flows of high density was implemented through the use of a liquid metal coolant based on the eutectic alloy Na-K. Requirements to improve the safety and compatibility of the design of the divertor with other in-vessel elements of the tokamak, cooled by water, and limiting the temperature of the lithium receiving surface at 2 led to the creation of a new design solution for the experimental module of the divertor and the use of a new coolant – gas dispersed water flow (gas-water spray). The article describes and justifies the design solutions of the new version of the module, the parameters of the coolant and the cooling system scheme. Experimental results on determination of heat transfer coefficient for coolant based on gas-water spray are considered
- 1 November 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1370 (1)
Open AccessLithium divertor of KTM tokamak
At present time the project of Kazakh material science tokamak KTM is under implementation. In addition to solving problems in the study of materials for fusion technologies on tokamak is working out innovative design elements of the divertor. The design of the lithium divertor module based on lithium capillary-porous systems has been developed and successfully tested under real tokamak conditions. In this design, the solution to the problem of removal of heat flows of high density was implemented through the use of a liquid metal coolant based on the eutectic alloy Na-K. Requirements to improve the safety and compatibility of the design of the divertor with other in-vessel elements of the tokamak, cooled by water, and limiting the temperature of the lithium receiving surface at 2 led to the creation of a new design solution for the experimental module of the divertor and the use of a new coolant – gas dispersed water flow (gas-water spray). The article describes and justifies the design solutions of the new version of the module, the parameters of the coolant and the cooling system scheme. Experimental results on determination of heat transfer coefficient for coolant based on gas-water spray are considered
- 1 September 2019
- Published by Elsevier in Fusion Engineering and Design
- Vol. 146, 1317-1320
Study of tritium and helium generation and release from lead-lithium eutectics Li15.7Pb under neutron irradiation
- 1 September 2019
- Published by Elsevier in Fusion Engineering and Design
- Vol. 146, 1317-1320
Study of tritium and helium generation and release from lead-lithium eutectics Li15.7Pb under neutron irradiation
- 1 September 2019
- Published by Elsevier in Fusion Engineering and Design
- Vol. 146, 402-405
Reactor studies of hydrogen isotopes interaction with lithium CPS using dynamic sorption technique
- 1 September 2019
- Published by Elsevier in Fusion Engineering and Design
- Vol. 146, 402-405
Reactor studies of hydrogen isotopes interaction with lithium CPS using dynamic sorption technique