Roman Pelo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Roman Pelo has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Mykhailo Hlobchak
Lviv Polytechnic National University
2 shared publications - Myroslav Oliskevych
L’viv National University of Nature Management
2 shared publications - Oleg Sorokivskyi
Національний університет "Львівська політехніка
2 shared publications - Oleh Kotsiumbas
Ivano-Frankivsk National Technical University of Oil and Gas
2 shared publications - Aliya Toktamyssova
Academy of Logistics and Transport
1 shared publication - Dana Aliakbarkyzy
Academy of Logistics and Transport
1 shared publication
Latest Publications
- Open Access
- 31 July 2026
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 367 (4) , 178-184
ПІДВИЩЕННЯ ЕФЕКТИВНОСТІ АВТОСЕРВІСНОГО ОБСЛУГОВУВАННЯ ТРАНСПОРТНИХ ЗАСОБІВ В УМОВАХ СУЧАСНИХ СТО
The article considers an applied problem of improving the operational efficiency of a vehicle service station by combining process analysis, standardization of repair operations, digital scheduling elements and calculation of queueing-system parameters. The relevance of the study is determined by the fact that modern service stations operate under uneven customer demand, increasing complexity of vehicle systems, shortage of qualified technicians, unstable availability of spare parts and higher customer expectations regarding repair time and service transparency. In contrast to approaches limited to a general discussion of service digitalization or separate recommendations for workplace organization, the paper proposes a consistent method for evaluating service-station efficiency through the interrelation of technical, organizational and economic indicators. The methodology is based on timing of typical operations, development of the process map “request - reception - diagnostics - repair - quality control - vehicle handover”, calculation of workstation utilization using the M/M/c queueing model, comparative evaluation of the baseline and improved workflow, and sensitivity analysis of vehicle time in the system depending on the intensity of arriving service requests. Using an illustrative production case of a service station with four work bays, it is shown that reduction of non-productive transitions, preliminary spare-parts preparation, online appointment scheduling, prioritization of service jobs and introduction of quality-control checkpoints can reduce the average waiting time in the queue from 40.1 to 11.7 minutes, while the average vehicle cycle time in the system decreases from 110.7 to 68.8 minutes. The results confirm that improving service-station performance should not be interpreted only as increasing the number of work bays or personnel, but primarily as optimizing workflow, reducing time losses and stabilizing the quality of operations. The practical value of the study lies in the possibility of applying the proposed method for operational audits of service stations, justification of changes in shift planning, identification of bottlenecks, development of KPI indicators for service advisors and repair teams, and preparation for the implementation of a digital service-order management system.
- 31 July 2026
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 367 (4) , 178-184
Open AccessПІДВИЩЕННЯ ЕФЕКТИВНОСТІ АВТОСЕРВІСНОГО ОБСЛУГОВУВАННЯ ТРАНСПОРТНИХ ЗАСОБІВ В УМОВАХ СУЧАСНИХ СТО
The article considers an applied problem of improving the operational efficiency of a vehicle service station by combining process analysis, standardization of repair operations, digital scheduling elements and calculation of queueing-system parameters. The relevance of the study is determined by the fact that modern service stations operate under uneven customer demand, increasing complexity of vehicle systems, shortage of qualified technicians, unstable availability of spare parts and higher customer expectations regarding repair time and service transparency. In contrast to approaches limited to a general discussion of service digitalization or separate recommendations for workplace organization, the paper proposes a consistent method for evaluating service-station efficiency through the interrelation of technical, organizational and economic indicators. The methodology is based on timing of typical operations, development of the process map “request - reception - diagnostics - repair - quality control - vehicle handover”, calculation of workstation utilization using the M/M/c queueing model, comparative evaluation of the baseline and improved workflow, and sensitivity analysis of vehicle time in the system depending on the intensity of arriving service requests. Using an illustrative production case of a service station with four work bays, it is shown that reduction of non-productive transitions, preliminary spare-parts preparation, online appointment scheduling, prioritization of service jobs and introduction of quality-control checkpoints can reduce the average waiting time in the queue from 40.1 to 11.7 minutes, while the average vehicle cycle time in the system decreases from 110.7 to 68.8 minutes. The results confirm that improving service-station performance should not be interpreted only as increasing the number of work bays or personnel, but primarily as optimizing workflow, reducing time losses and stabilizing the quality of operations. The practical value of the study lies in the possibility of applying the proposed method for operational audits of service stations, justification of changes in shift planning, identification of bottlenecks, development of KPI indicators for service advisors and repair teams, and preparation for the implementation of a digital service-order management system.
- 1 January 2025
- Published by Lviv Polytechnic National University in Ukrainian journal of mechanical engineering and materials science
- Vol. 11 (3) , 1-10
COMPUTER SIMULATION AND EXPERIMENTAL VERIFICATION OF RECTILINEAR MOTION TRAJECTORIES OF A SINGLE-MASS OSCILLATORY SYSTEM ACTUATED BY AN INERTIAL PLANETARY-TYPE VIBRATION EXCITER
Problem statement and purpose of research. This study investigates whether a planetary-type inertial exciter can synthesize rectilinear motion trajectories in a single-mass oscillatory system and how the orientation of that trajectory can be programmed mechanically. Methodology. A three-dimensional CAD assembly was created and analyzed using multibody simulations to compute planar displacements, velocities, and accelerations under representative stiffness, damping, and mass properties. The initial carrier-arm angle was used as the primary design variable. A laboratory rig with orthogonal potentiometric sensing measured horizontal and vertical displacements; corresponding trajectories in the vertical plane were reconstructed for multiple geometric configurations. Findings. Simulations predict, and experiments confirm, a one-to-one mapping between the angle being studied and the direction of the straight-line path: horizontal, vertical, or inclined. In all cases, the displacement components are nearly sinusoidal and largely in phase; the component aligned with the target direction dominates in amplitude, while the orthogonal component remains small, causing the Lissajous figure to collapse toward a line. Minor non-smoothness in measured trajectories indicates high-frequency content from non-idealities (e.g., transmission compliance, local resonances), suggesting model extensions but not affecting the primary orientation control. Originality. The work demonstrates mechanism-level trajectory programming of rectilinear motion using a single-DOF planetary exciter, validated experimentally, thereby avoiding multi-actuator synchronization or semi-active control. Practical value. The results provide a simple, reproducible design lever – the initial arm angle – for setting line orientation in vibratory equipment requiring directional impulse transfer with minimal transverse motion. Future scope. Recommended directions of further research include tolerance and robustness analyses, incorporation of gear and belt compliance, and closed-loop trimming strategies to maintain rectilinearity under parameter drift.
- 1 January 2025
- Published by Lviv Polytechnic National University in Ukrainian journal of mechanical engineering and materials science
- Vol. 11 (3) , 1-10
COMPUTER SIMULATION AND EXPERIMENTAL VERIFICATION OF RECTILINEAR MOTION TRAJECTORIES OF A SINGLE-MASS OSCILLATORY SYSTEM ACTUATED BY AN INERTIAL PLANETARY-TYPE VIBRATION EXCITER
Problem statement and purpose of research. This study investigates whether a planetary-type inertial exciter can synthesize rectilinear motion trajectories in a single-mass oscillatory system and how the orientation of that trajectory can be programmed mechanically. Methodology. A three-dimensional CAD assembly was created and analyzed using multibody simulations to compute planar displacements, velocities, and accelerations under representative stiffness, damping, and mass properties. The initial carrier-arm angle was used as the primary design variable. A laboratory rig with orthogonal potentiometric sensing measured horizontal and vertical displacements; corresponding trajectories in the vertical plane were reconstructed for multiple geometric configurations. Findings. Simulations predict, and experiments confirm, a one-to-one mapping between the angle being studied and the direction of the straight-line path: horizontal, vertical, or inclined. In all cases, the displacement components are nearly sinusoidal and largely in phase; the component aligned with the target direction dominates in amplitude, while the orthogonal component remains small, causing the Lissajous figure to collapse toward a line. Minor non-smoothness in measured trajectories indicates high-frequency content from non-idealities (e.g., transmission compliance, local resonances), suggesting model extensions but not affecting the primary orientation control. Originality. The work demonstrates mechanism-level trajectory programming of rectilinear motion using a single-DOF planetary exciter, validated experimentally, thereby avoiding multi-actuator synchronization or semi-active control. Practical value. The results provide a simple, reproducible design lever – the initial arm angle – for setting line orientation in vibratory equipment requiring directional impulse transfer with minimal transverse motion. Future scope. Recommended directions of further research include tolerance and robustness analyses, incorporation of gear and belt compliance, and closed-loop trimming strategies to maintain rectilinearity under parameter drift.
- Open Access
- 31 December 2022
- Published by Private Company Technology Center
- p. 75–107
Coordination of material and information flows in intercity logistics systems
The problem of the effectiveness of the use of road transport in logistics systems is considered. Carriers attract additional motor vehicles according to increasing in freight turnover, namely in long-distance routes. The trend of growth in the volume of transportation and the distance of cargo transportation has been maintained in recent years, despite the crisis periods in the economies of the European Union countries. However, the increase in the number of vehicles of fleets is accompanied by an increase in their idle time and delays in the delivery of goods. This phenomenon is explained by the lack of necessary coordination of material flows on the transport network. We considered two types of material flows, namely cargo flows and automobile flows. Both types of flows are discrete in nature. In order to represent the interaction of material flows in the logistics system, the term elementary logistics operation is used, which is the smallest constant element of the logistics chain. Despite the wide variety of processes that occur in logistics systems, the number of typical elementary logistics operations is limited and quite small. For the numerical characterization of material flows, such parameters as a tact, a front, the size of a group of material elements, and the average intensity of the flow are used. Based on the known dependencies between these parameters and taking into account the connections of elementary logistics operations, a structural model of logistics chains is built. It is taken into account that information messages in the logistics system arise when material flows change. The impact of changes in the intensity of cargo flows in logistics chains has been studied and the majority of sources of information messages in space and time have been determined. It has been proven that the use of the objectively necessary amount of information with the necessary advance time makes it possible to reduce dynamic and static delays of cargo flows to a minimum. Due to the fact that changes in the intensity of material flows occur stochastically in logistics chains, the feasibility of assessing the resistance of a given logistics system to external disturbances was developed. The influence of information provision of truck crews performing transport tasks on highway connections is studied. An information support scheme has been developed on the terms of cargo delivery with the need for the truck to arrive at the unloading point on time.
- 31 December 2022
- Published by Private Company Technology Center
- p. 75–107
Open AccessCoordination of material and information flows in intercity logistics systems
The problem of the effectiveness of the use of road transport in logistics systems is considered. Carriers attract additional motor vehicles according to increasing in freight turnover, namely in long-distance routes. The trend of growth in the volume of transportation and the distance of cargo transportation has been maintained in recent years, despite the crisis periods in the economies of the European Union countries. However, the increase in the number of vehicles of fleets is accompanied by an increase in their idle time and delays in the delivery of goods. This phenomenon is explained by the lack of necessary coordination of material flows on the transport network. We considered two types of material flows, namely cargo flows and automobile flows. Both types of flows are discrete in nature. In order to represent the interaction of material flows in the logistics system, the term elementary logistics operation is used, which is the smallest constant element of the logistics chain. Despite the wide variety of processes that occur in logistics systems, the number of typical elementary logistics operations is limited and quite small. For the numerical characterization of material flows, such parameters as a tact, a front, the size of a group of material elements, and the average intensity of the flow are used. Based on the known dependencies between these parameters and taking into account the connections of elementary logistics operations, a structural model of logistics chains is built. It is taken into account that information messages in the logistics system arise when material flows change. The impact of changes in the intensity of cargo flows in logistics chains has been studied and the majority of sources of information messages in space and time have been determined. It has been proven that the use of the objectively necessary amount of information with the necessary advance time makes it possible to reduce dynamic and static delays of cargo flows to a minimum. Due to the fact that changes in the intensity of material flows occur stochastically in logistics chains, the feasibility of assessing the resistance of a given logistics system to external disturbances was developed. The influence of information provision of truck crews performing transport tasks on highway connections is studied. An information support scheme has been developed on the terms of cargo delivery with the need for the truck to arrive at the unloading point on time.
- Open Access
- 9 June 2022
- Published by Lutsk National Technical University in СУЧАСНІ ТЕХНОЛОГІЇ В МАШИНОБУДУВАННІ ТА ТРАНСПОРТІ
- Vol. 1 (18) , 66-73
СИНТЕЗ ЧАСТОСТІ ВИКОРИСТАННЯ ПЕРЕДАЧ СХІДЧАСТОЇ КОРОБКИ ПЕРЕМИКАННЯ ПЕРЕДАЧ (КПП) У ПРОЦЕСІ ВІДТВОРЕННЯ ТИПОВИХ ЦИКЛІВ
Ретроспективний аналіз ситуації транспортних потоків в умовах міських перевезень свідчить про різноманіття вантажних траснпортних засобів як за вантажністю так і за класом. Окрім цього транспортний потік у вказаних умовах характеризується великою щільністю. Вище сказане накладає низку обмежень, зокрема, на конструктивні параметри транспортних засобів, ба більше, на вибір силової установки. Значна частина транспортних засобів, що формують такий потік в умовах населених пунктів, зокрема, великих обласних центрів, оснащені силовими агрегатами у складі ДВЗ механічна східчаста коробка передач (МСКП). Відомо, що програма руху окремого взятого транспортного засобу близька до циклічного (за наявністю окремих фаз). Визначальним для ідентифікації програм руху є аналіз реальних маршрутів дрібногуртових перевезень в умовах міста Львова, що характеризується варіативністю відстаней та тривалостей їхньої реалізації. Домінуючими в умовах міста є транспортні засоби оснащені, переважно, 4 6-ти східчасті траснсмісії. Обмеженння швидкості і короткі, здебільшого, відстані між пунктами циклу, дають підстави стосовно доцільності використання в якості елемента трансмісії багатосхідчастих МСКП. Відтак постає завдання стосовно дослідження кількості перемикань за рахунок визначення частості тієї чи іншої передачі в МСКП в умовах міського транспортного руху. Метою дослідження є виявити доцільність використання усіх передач транспортного засобу з конструктивної точки зору для транспортних засобів, які задіяні в таких умовах експлуатації. Ключові слова: коробка передач, базовий та еквівалентний їздові цикли, розганяння, вибіг, сповільнення, частість передачі.
- 9 June 2022
- Published by Lutsk National Technical University in СУЧАСНІ ТЕХНОЛОГІЇ В МАШИНОБУДУВАННІ ТА ТРАНСПОРТІ
- Vol. 1 (18) , 66-73
Open AccessСИНТЕЗ ЧАСТОСТІ ВИКОРИСТАННЯ ПЕРЕДАЧ СХІДЧАСТОЇ КОРОБКИ ПЕРЕМИКАННЯ ПЕРЕДАЧ (КПП) У ПРОЦЕСІ ВІДТВОРЕННЯ ТИПОВИХ ЦИКЛІВ
Ретроспективний аналіз ситуації транспортних потоків в умовах міських перевезень свідчить про різноманіття вантажних траснпортних засобів як за вантажністю так і за класом. Окрім цього транспортний потік у вказаних умовах характеризується великою щільністю. Вище сказане накладає низку обмежень, зокрема, на конструктивні параметри транспортних засобів, ба більше, на вибір силової установки. Значна частина транспортних засобів, що формують такий потік в умовах населених пунктів, зокрема, великих обласних центрів, оснащені силовими агрегатами у складі ДВЗ механічна східчаста коробка передач (МСКП). Відомо, що програма руху окремого взятого транспортного засобу близька до циклічного (за наявністю окремих фаз). Визначальним для ідентифікації програм руху є аналіз реальних маршрутів дрібногуртових перевезень в умовах міста Львова, що характеризується варіативністю відстаней та тривалостей їхньої реалізації. Домінуючими в умовах міста є транспортні засоби оснащені, переважно, 4 6-ти східчасті траснсмісії. Обмеженння швидкості і короткі, здебільшого, відстані між пунктами циклу, дають підстави стосовно доцільності використання в якості елемента трансмісії багатосхідчастих МСКП. Відтак постає завдання стосовно дослідження кількості перемикань за рахунок визначення частості тієї чи іншої передачі в МСКП в умовах міського транспортного руху. Метою дослідження є виявити доцільність використання усіх передач транспортного засобу з конструктивної точки зору для транспортних засобів, які задіяні в таких умовах експлуатації. Ключові слова: коробка передач, базовий та еквівалентний їздові цикли, розганяння, вибіг, сповільнення, частість передачі.
- Open Access
- 28 February 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (3(115)) , 13-23
Optimization of schedules for early garbage collection and disposal in the megapolis
It is shown that due to the growth of waste generated by the metropolis, the processes of their removal and disposal must be more accurately accounted and controlled. If it is impossible to introduce “smart” control systems, it is proposed to search for reserves to increase the efficiency of the processes in their structure. A structural model of operations has been developed that can reduce time costs. The use of incomplete information on the accumulation and removal of garbage leads to unplanned mileage of trucks. In order to avoid unforeseen costs, it is proposed to use early garbage collection, which reduces the frequency of emptying containers. This leads to an increase in the number of truck arrivals to load, but eliminates unforeseen mileage due to inconsistencies in the loading forecast. It is shown that to effectively organize the work of garbage trucks on the transport network of the city, an active, shortest schedule of operations is required, which must be made for several periods. To develop an optimal cyclic schedule of garbage trucks, a method based on the ordering of mixed graphs is proposed. The mixed graph shows the set of garbage collection operations and the time relationships between their execution times. In order to develop an optimal schedule from such a graph, cycles must be removed from the graph. To do this, the “divide and conquer” method was used. The proposed algorithm for graph ordering is used to study the current garbage collection system. As a result of research, higher productivity of garbage trucks and timely removal of organic waste were achieved. The reduction of the weekly working time of 6 garbage trucks with the use of the 70 % container filling level reached 42 hours.
- 28 February 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (3(115)) , 13-23
Open AccessOptimization of schedules for early garbage collection and disposal in the megapolis
It is shown that due to the growth of waste generated by the metropolis, the processes of their removal and disposal must be more accurately accounted and controlled. If it is impossible to introduce “smart” control systems, it is proposed to search for reserves to increase the efficiency of the processes in their structure. A structural model of operations has been developed that can reduce time costs. The use of incomplete information on the accumulation and removal of garbage leads to unplanned mileage of trucks. In order to avoid unforeseen costs, it is proposed to use early garbage collection, which reduces the frequency of emptying containers. This leads to an increase in the number of truck arrivals to load, but eliminates unforeseen mileage due to inconsistencies in the loading forecast. It is shown that to effectively organize the work of garbage trucks on the transport network of the city, an active, shortest schedule of operations is required, which must be made for several periods. To develop an optimal cyclic schedule of garbage trucks, a method based on the ordering of mixed graphs is proposed. The mixed graph shows the set of garbage collection operations and the time relationships between their execution times. In order to develop an optimal schedule from such a graph, cycles must be removed from the graph. To do this, the “divide and conquer” method was used. The proposed algorithm for graph ordering is used to study the current garbage collection system. As a result of research, higher productivity of garbage trucks and timely removal of organic waste were achieved. The reduction of the weekly working time of 6 garbage trucks with the use of the 70 % container filling level reached 42 hours.
- Open Access
- 1 May 2021
- Published by Kharkiv National Automobile and Highway University in Vehicle and Electronics. Innovative Technologies
- No. 19,p. 35-40
Comparative evaluation of dynamics and fuel efficiency indicators of the car with robotic stepped transmission under condition of different diameters of engine cylinders
Problem. Repair dimensions method regulates increment of cylinders by the means of mechanical treatment, which leads to increasing of working volume of the engine. This will cause a change of dynamics and fuel-efficiensy indicators of the car with the certain type of transmission. Goal. The goal is to comparatively evaluate dynamism and fuel-efficiency of automotive vehicle category N2 with two options of engines, which have nominal and repair cylinder sizes. The riding cycle of the cars with robotic stepped gearbox was researched, that is without breaking of force stream while switching gears. Methology. Imitative simulation of cars riding cycle, according to standard, was conducted with the help of Matlab Simulink software. Because of the fact that mathematical model of cars movement during mentioned cycle is based on elementary dependencies, for its realization the only basics avialable blocks of the sofware package were used. The flowchart is given in the paper. Results. Simulation of riding cycle of N2 – category automotive vehicle with robotic gearbox was conducted at full engine’s capacity while running-up. Obtained results have shown that engines with repairment sizes have advantage in dynamism indicators, engines with nominal cylinder sizes have advantages in fuel-efficiency. Originality. For obtaining of comparative evaluation of dynamics and fuel-efficiency indicators of the car with robotic gearbox with different engines, the imitation simulation of riding cycle, according to standarts, was used with the help of Matlab Simulink software. Practical value. Application of the repairment sizes method upon the engine’s cylinder liners has shown improvement of dynamics indicators of car with robotic transmission, which will improve its productivity under excessive engines work conditions.
- 1 May 2021
- Published by Kharkiv National Automobile and Highway University in Vehicle and Electronics. Innovative Technologies
- No. 19,p. 35-40
Open AccessComparative evaluation of dynamics and fuel efficiency indicators of the car with robotic stepped transmission under condition of different diameters of engine cylinders
Problem. Repair dimensions method regulates increment of cylinders by the means of mechanical treatment, which leads to increasing of working volume of the engine. This will cause a change of dynamics and fuel-efficiensy indicators of the car with the certain type of transmission. Goal. The goal is to comparatively evaluate dynamism and fuel-efficiency of automotive vehicle category N2 with two options of engines, which have nominal and repair cylinder sizes. The riding cycle of the cars with robotic stepped gearbox was researched, that is without breaking of force stream while switching gears. Methology. Imitative simulation of cars riding cycle, according to standard, was conducted with the help of Matlab Simulink software. Because of the fact that mathematical model of cars movement during mentioned cycle is based on elementary dependencies, for its realization the only basics avialable blocks of the sofware package were used. The flowchart is given in the paper. Results. Simulation of riding cycle of N2 – category automotive vehicle with robotic gearbox was conducted at full engine’s capacity while running-up. Obtained results have shown that engines with repairment sizes have advantage in dynamism indicators, engines with nominal cylinder sizes have advantages in fuel-efficiency. Originality. For obtaining of comparative evaluation of dynamics and fuel-efficiency indicators of the car with robotic gearbox with different engines, the imitation simulation of riding cycle, according to standarts, was used with the help of Matlab Simulink software. Practical value. Application of the repairment sizes method upon the engine’s cylinder liners has shown improvement of dynamics indicators of car with robotic transmission, which will improve its productivity under excessive engines work conditions.