Daria Topal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Daria Topal has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Daria Grabco
Institute of Applied Physics, MD-2028, Chisinau, Moldova
3 shared publications - Olga Shikimaka
Academy of Sciences of Moldova
3 shared publications - Andrian Prisacaru
Technical University of Moldova, 168, Ștefan cel Mare Blvd., Chisinau, Republic of Moldova
2 shared publications - Constantin Pyrtsac
Moldova State University
2 shared publications - Dragisha Vilotici
University of Novi Sad, Faculty of Technical Sciences, Novi Sad, Serbia
1 shared publication - Marko Vilotic
University of Novi Sad, Faculty of technical sciences, Trg Dositeja Obradovića 6, 21000 Novi Sad, Serbia
1 shared publication
Latest Publications
- 1 January 2025
- Published by Moldova State University
- p. 835-842
Similarities and differences in the specificity of deformation of AISI 316L steel under friction and impact loading conditions
The paper studies the formation of a hardened nano-microstructured (NMS) surface layer on AISI 316L stainless steel using two methods: light friction and light impact loading. The studies have shown that the forming NMS layer has both common and different features that can affect the properties of the modified material in different ways. The common features of the NMS layer under friction and impact loading include the fragmentation of the grain structure, the appearance of slip bands inside the grains, an increase in the strength and plasticity parameters. On the other hand, some differences are noted: a different degree of hardening in the NMS layer compared to the original undeformed surface, different sizes of the NMS layer, etc. Based on the obtained results, it can be assumed that the friction method can be used to obtain a slightly strengthened NMS layer with a thickness of about 500 μm. The impact load method is preferable for obtaining a more strengthened NMS layer of thickness ≈15-20 μm.
- 1 January 2025
- Published by Moldova State University
- p. 835-842
Similarities and differences in the specificity of deformation of AISI 316L steel under friction and impact loading conditions
The paper studies the formation of a hardened nano-microstructured (NMS) surface layer on AISI 316L stainless steel using two methods: light friction and light impact loading. The studies have shown that the forming NMS layer has both common and different features that can affect the properties of the modified material in different ways. The common features of the NMS layer under friction and impact loading include the fragmentation of the grain structure, the appearance of slip bands inside the grains, an increase in the strength and plasticity parameters. On the other hand, some differences are noted: a different degree of hardening in the NMS layer compared to the original undeformed surface, different sizes of the NMS layer, etc. Based on the obtained results, it can be assumed that the friction method can be used to obtain a slightly strengthened NMS layer with a thickness of about 500 μm. The impact load method is preferable for obtaining a more strengthened NMS layer of thickness ≈15-20 μm.
- 1 September 2024
- Published by Moldova State University in Elektronnaya Obrabotka Materialov
- Vol. 60 (4) , 14-23
Deformation by light Impacts to Create a Near-Surface Nano- and Microstructured Layer in AISI 316L Stainless Steel
A nano- and microstructured surface layer (NMSSL) was created on an AISI 316L stainless steel sample by impact loading. As a result of the impacts, a change in the microstructure of the test sample was observed: a decrease in the size of the grains, an increase in their misorientation, the appearance of slip bands inside the grains, the appearance of rounded shapes of different sizes (0,1–15 μm) and with different densities on the surface of the sample. Moreover, these nanomicrocrystalline grains had random crystallographic orientation. The microhardness of the deformed surface was assessed using the Vickers and Berkovich methods. The hardness imprints had an approximately equiaxial shape, but the sides of the imprints were often distorted. The microhardness on the impact-deformed surface ranged as Н = 2.7–4.2 GPa depending on the number of impacts, increasing with their growth and decreasing with the distance from the impact surface. The microhardness of the undeformed sample was 2.0 GPa. The main patterns of formation of the deformed layer depending on the number of impacts have been revealed.
- 1 September 2024
- Published by Moldova State University in Elektronnaya Obrabotka Materialov
- Vol. 60 (4) , 14-23
Deformation by light Impacts to Create a Near-Surface Nano- and Microstructured Layer in AISI 316L Stainless Steel
A nano- and microstructured surface layer (NMSSL) was created on an AISI 316L stainless steel sample by impact loading. As a result of the impacts, a change in the microstructure of the test sample was observed: a decrease in the size of the grains, an increase in their misorientation, the appearance of slip bands inside the grains, the appearance of rounded shapes of different sizes (0,1–15 μm) and with different densities on the surface of the sample. Moreover, these nanomicrocrystalline grains had random crystallographic orientation. The microhardness of the deformed surface was assessed using the Vickers and Berkovich methods. The hardness imprints had an approximately equiaxial shape, but the sides of the imprints were often distorted. The microhardness on the impact-deformed surface ranged as Н = 2.7–4.2 GPa depending on the number of impacts, increasing with their growth and decreasing with the distance from the impact surface. The microhardness of the undeformed sample was 2.0 GPa. The main patterns of formation of the deformed layer depending on the number of impacts have been revealed.
- Open Access
- 1 June 2021
- Published by Technical University of Moldova in Journal of Engineering Science
- Vol. XXVIII (2) , 34-43
EFFECT OF FRICTION ON THE MICROMECHANICAL PROPERTIES OF AISI 316L AUSTENITIC STEEL
In this paper, we investigate the possibility of using the friction method for modifying the microstructure and mechanical properties in the near-surface regions of AISI 316L austenitic steel specimens for the purpose of its practical application. It is shown that a region of severe plastic deformation arises near the friction surface, which transforms the initial fine-grained polycrystalline steel structure into a homogenized zone consisting of a deformed structure with plastic slip bands and weakly pronounced grain boundaries. The change in the microscopic structure results in an increase in this zone of values of micromechanical characteristics, such as microhardness (H), Young's modulus (E), plasticity index (H/E) and resistance index (H3/E2). The obtained results are of interest for the potential use of AISI 316L steel in medicine.
- 1 June 2021
- Published by Technical University of Moldova in Journal of Engineering Science
- Vol. XXVIII (2) , 34-43
Open AccessEFFECT OF FRICTION ON THE MICROMECHANICAL PROPERTIES OF AISI 316L AUSTENITIC STEEL
In this paper, we investigate the possibility of using the friction method for modifying the microstructure and mechanical properties in the near-surface regions of AISI 316L austenitic steel specimens for the purpose of its practical application. It is shown that a region of severe plastic deformation arises near the friction surface, which transforms the initial fine-grained polycrystalline steel structure into a homogenized zone consisting of a deformed structure with plastic slip bands and weakly pronounced grain boundaries. The change in the microscopic structure results in an increase in this zone of values of micromechanical characteristics, such as microhardness (H), Young's modulus (E), plasticity index (H/E) and resistance index (H3/E2). The obtained results are of interest for the potential use of AISI 316L steel in medicine.