Dragisha Vilotici
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dragisha Vilotici has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Marko Vilotic
University of Novi Sad, Faculty of technical sciences, Trg Dositeja Obradovića 6, 21000 Novi Sad, Serbia
2 shared publications - Andrian Prisacaru
Technical University of Moldova, 168, Ștefan cel Mare Blvd., Chisinau, Republic of Moldova
1 shared publication - Constantin Pyrtsac
Moldova State University
1 shared publication - Daria Grabco
Institute of Applied Physics, MD-2028, Chisinau, Moldova
1 shared publication - Daria Topal
Institute of Applied Physics, Chisinau, Moldova Rep
1 shared publication - Marina Rynkovskaya
RUDN University
1 shared publication
Latest Publications
- Open Access
- 18 December 2025
- Published by Faculty of Technical Sciences in Advanced Technologies & Materials
- Vol. 50 (2) , 17-24
Workability Limit Diagram at Plane Stress Condition
Numerous experimental studies of workability limit diagrams in the domain of bulk deformation have been performed on specimens where failure occurs at the free surface, i.e., under plane stress conditions. Previous investigations of workability diagrams using compression tests on axially symmetric specimens have yielded negative values of the stress triaxiality ratio (β < –1), while positive values have predominantly been obtained from tensile tests, often exceeding β > +3. The objective of the present study is to explore the applicability of additional deformation models under plane stress conditions that could extend the workability diagram into regions corresponding to negative stress triaxiality ratio values. Additionally, the study aims to determine the limiting values of the stress triaxiality ratio under such stress conditions. For cold bulk forming processes, the region of the workability diagram associated with negative stress triaxiality ratio values (β < –1) is of particular technological importance. The analysis of various formability tests under plane stress conditions was conducted using idealized deformation models, in which the deformation path was assumed to be linear.
- 18 December 2025
- Published by Faculty of Technical Sciences in Advanced Technologies & Materials
- Vol. 50 (2) , 17-24
Open AccessWorkability Limit Diagram at Plane Stress Condition
Numerous experimental studies of workability limit diagrams in the domain of bulk deformation have been performed on specimens where failure occurs at the free surface, i.e., under plane stress conditions. Previous investigations of workability diagrams using compression tests on axially symmetric specimens have yielded negative values of the stress triaxiality ratio (β < –1), while positive values have predominantly been obtained from tensile tests, often exceeding β > +3. The objective of the present study is to explore the applicability of additional deformation models under plane stress conditions that could extend the workability diagram into regions corresponding to negative stress triaxiality ratio values. Additionally, the study aims to determine the limiting values of the stress triaxiality ratio under such stress conditions. For cold bulk forming processes, the region of the workability diagram associated with negative stress triaxiality ratio values (β < –1) is of particular technological importance. The analysis of various formability tests under plane stress conditions was conducted using idealized deformation models, in which the deformation path was assumed to be linear.
- 1 January 2025
- Published by Moldova State University
- p. 835-842
Similarities and differences in the specificity of deformation of AISI 316L steel under friction and impact loading conditions
The paper studies the formation of a hardened nano-microstructured (NMS) surface layer on AISI 316L stainless steel using two methods: light friction and light impact loading. The studies have shown that the forming NMS layer has both common and different features that can affect the properties of the modified material in different ways. The common features of the NMS layer under friction and impact loading include the fragmentation of the grain structure, the appearance of slip bands inside the grains, an increase in the strength and plasticity parameters. On the other hand, some differences are noted: a different degree of hardening in the NMS layer compared to the original undeformed surface, different sizes of the NMS layer, etc. Based on the obtained results, it can be assumed that the friction method can be used to obtain a slightly strengthened NMS layer with a thickness of about 500 μm. The impact load method is preferable for obtaining a more strengthened NMS layer of thickness ≈15-20 μm.
- 1 January 2025
- Published by Moldova State University
- p. 835-842
Similarities and differences in the specificity of deformation of AISI 316L steel under friction and impact loading conditions
The paper studies the formation of a hardened nano-microstructured (NMS) surface layer on AISI 316L stainless steel using two methods: light friction and light impact loading. The studies have shown that the forming NMS layer has both common and different features that can affect the properties of the modified material in different ways. The common features of the NMS layer under friction and impact loading include the fragmentation of the grain structure, the appearance of slip bands inside the grains, an increase in the strength and plasticity parameters. On the other hand, some differences are noted: a different degree of hardening in the NMS layer compared to the original undeformed surface, different sizes of the NMS layer, etc. Based on the obtained results, it can be assumed that the friction method can be used to obtain a slightly strengthened NMS layer with a thickness of about 500 μm. The impact load method is preferable for obtaining a more strengthened NMS layer of thickness ≈15-20 μm.