Gaston Rauchs
Research Subjects
Gaston Rauchs has a total of 83 co-authors. Here are the top co-authors by number of shared publications:
- Philip John Withers
The University of Manchester
8 shared publications - Salim Belouettar
Luxembourg Institute of Science and Technology, Esch-sur-Alzette, Luxembourg
6 shared publications D. Munz
Universität Karlsruhe
4 shared publications- Julien Bardon
Luxembourg Institute of Science and Technology (LIST) Esch‐sur‐Alzette Luxembourg
4 shared publications T. Fett
Institut für Materialforschung II
4 shared publicationsM. Azaouzi
3 shared publications
Latest Publications
- Open Access
- 8 May 2026
- Published by Elsevier in Journal of Power Sources
- Vol. 681
From Microstructure to Macroscopic Performance: An optimization pipeline for solid oxide fuel cell microstructures
- 8 May 2026
- Published by Elsevier in Journal of Power Sources
- Vol. 681
Open AccessFrom Microstructure to Macroscopic Performance: An optimization pipeline for solid oxide fuel cell microstructures
- Open Access
- 25 September 2025
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 30 (3)
Efficient AI-aided segmentation of concrete CT scans using a predictive annotation interface
- 25 September 2025
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 30 (3)
Open AccessEfficient AI-aided segmentation of concrete CT scans using a predictive annotation interface
- Open Access
- 1 July 2024
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 21 (6) , 3863-3875
Additive manufacturing of short fiber oxide ceramic matrix composite: Process analysis and material properties
This work investigates the material extrusion‐based additive manufacturing (AM) process chain of a pure alumina‐based oxide ceramic matrix composite, starting from material selection, large‐scale compounding to pellets, the AM process itself, debinding and sintering as well as microstructural and mechanical characterization. The compounded pellets have a volume share of 50% binder (polyvinyl butyral [PVB], polyethylene glycol [PEG], and stearic acid) and 50% alumina (Al 2 O 3 , alumina powder, and Nextel 610 alumina fibers) with an aimed fiber volume share of 40% after sintering. The material is compounded on an industrial scale with approximately 10 kg/h and the material extrusion‐based AM process reaches speeds of up to 1000 mm/s. A variation of the feed rate leads to a significant increase in surface roughness and an increase in mass of 30%, in thickness of 12% and in width of 25%. The flexural behavior in the four‐point‐bending test can be described by a fast first peak and reaching higher flexural strength after the first crack subsequent with averages of 23.8 ± 3.6 MPa below .1% elongation. The fracture surfaces show the expected failure mechanisms like pull‐out and crack deflection. The resulting fiber length in the printed samples is 140 µm in average.
- 1 July 2024
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 21 (6) , 3863-3875
Open AccessAdditive manufacturing of short fiber oxide ceramic matrix composite: Process analysis and material properties
This work investigates the material extrusion‐based additive manufacturing (AM) process chain of a pure alumina‐based oxide ceramic matrix composite, starting from material selection, large‐scale compounding to pellets, the AM process itself, debinding and sintering as well as microstructural and mechanical characterization. The compounded pellets have a volume share of 50% binder (polyvinyl butyral [PVB], polyethylene glycol [PEG], and stearic acid) and 50% alumina (Al 2 O 3 , alumina powder, and Nextel 610 alumina fibers) with an aimed fiber volume share of 40% after sintering. The material is compounded on an industrial scale with approximately 10 kg/h and the material extrusion‐based AM process reaches speeds of up to 1000 mm/s. A variation of the feed rate leads to a significant increase in surface roughness and an increase in mass of 30%, in thickness of 12% and in width of 25%. The flexural behavior in the four‐point‐bending test can be described by a fast first peak and reaching higher flexural strength after the first crack subsequent with averages of 23.8 ± 3.6 MPa below .1% elongation. The fracture surfaces show the expected failure mechanisms like pull‐out and crack deflection. The resulting fiber length in the printed samples is 140 µm in average.
- Open Access
- 1 August 2021
- Published by Elsevier in Polymer Testing
- Vol. 100
Resolving cavitation in silica-filled styrene-butadiene rubber composites upon cyclic tensile testing
- 1 August 2021
- Published by Elsevier in Polymer Testing
- Vol. 100
Open AccessResolving cavitation in silica-filled styrene-butadiene rubber composites upon cyclic tensile testing
- Open Access
- 1 November 2020
- Published by Elsevier in Composite Structures
- Vol. 251
Efficient uncertainty quantification and management in the early stage design of composite applications
- 1 November 2020
- Published by Elsevier in Composite Structures
- Vol. 251
Open AccessEfficient uncertainty quantification and management in the early stage design of composite applications
- Open Access
- 1 November 2018
- Published by Elsevier in Composite Structures
- Vol. 204, 778-790
Integration of material and process modelling in a business decision support system: Case of COMPOSELECTOR H2020 project
- 1 November 2018
- Published by Elsevier in Composite Structures
- Vol. 204, 778-790
Open AccessIntegration of material and process modelling in a business decision support system: Case of COMPOSELECTOR H2020 project
- 1 May 2016
- Published by Elsevier in Ceramics International
- Vol. 42 (7) , 8360-8375
Shape optimization of ceramic components using a failure probability based on extended multiaxial Weibull theory
- 1 May 2016
- Published by Elsevier in Ceramics International
- Vol. 42 (7) , 8360-8375
Shape optimization of ceramic components using a failure probability based on extended multiaxial Weibull theory
- 1 February 2016
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 681, 47-85
A Quadratic Contact Element Passing the Patch Test
For the two dimensional contact modeling, the standard node-to-segment quadratic contact elements are known to exhibit oscillations of the contact pressure. This situation is particularly critical when using the penalty method with a high penalty parameter because the amplitude of the oscillations increase with increasing penalty parameter. The aim of this article is to present a method for removing the oscillations of contact pressure observed while using quadratic contact element. For this purpose, the nodal forces at the slave and at the master nodes need to be evaluated appropriately. One possibility is to develop a suitable procedure for computing the nodal forces. In that sake, we selected the approach first proposed in [35] in an appropriate manner. After presenting the improved quadratic contact element, some numerical examples are illustrated in this paper to comparethe standard quadratic node-to-segment element with the proposed element. The examples show that the proposed element can strongly reduce the oscillating contact pressure for both plane and curved contact surfaces.
- 1 February 2016
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 681, 47-85
A Quadratic Contact Element Passing the Patch Test
For the two dimensional contact modeling, the standard node-to-segment quadratic contact elements are known to exhibit oscillations of the contact pressure. This situation is particularly critical when using the penalty method with a high penalty parameter because the amplitude of the oscillations increase with increasing penalty parameter. The aim of this article is to present a method for removing the oscillations of contact pressure observed while using quadratic contact element. For this purpose, the nodal forces at the slave and at the master nodes need to be evaluated appropriately. One possibility is to develop a suitable procedure for computing the nodal forces. In that sake, we selected the approach first proposed in [35] in an appropriate manner. After presenting the improved quadratic contact element, some numerical examples are illustrated in this paper to comparethe standard quadratic node-to-segment element with the proposed element. The examples show that the proposed element can strongly reduce the oscillating contact pressure for both plane and curved contact surfaces.
- 1 February 2016
- Published by Elsevier in Finite Elements in Analysis and Design
- Vol. 109, 65-72
Direct-differentiation-based sensitivity analysis of an axisymmetric finite element formulation including torsion
- 1 February 2016
- Published by Elsevier in Finite Elements in Analysis and Design
- Vol. 109, 65-72
Direct-differentiation-based sensitivity analysis of an axisymmetric finite element formulation including torsion