Goran Marković
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Goran Marković has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Mile Savković
Faculty of Mechanical and Civil Engineering University of Kragujevac Kraljevo Serbia
9 shared publications - Nebojša Zdravković
Department of Medical Statistics and Informatics, Faculty of Medical Sciences, University of Kragujevac, Svetozara Markovića 69, 34000 Kragujevac, Serbia
9 shared publications - Goran V. Pavlović
Faculty of Electronic Engineering, University of Nis, Nis, Serbia
6 shared publications - Marko Todorović
University of Kragujevac, Faculty of Mechanical and Civil Engineering, Kraljevo, Serbia
5 shared publications - Milomir Gašić
University of Kragujevac
4 shared publications Nebojša Zdravković
4 shared publications
Latest Publications
- 1 January 2026
- Published by University Library in Kragujevac
- p. A51-A57
The determination of the deflection of the stepped column by the finite difference method
Besides the strength criterion, steel structures must also meet the deformation criterion, which in some cases may be critical. Excessive deformation of the structure may lead to additional loads and improper operation of the installed equipment. The most common practice in steel structure design involves using the finite element method (FEM) to calculate the stress and deformation of the current model. However, this is usually limited to the case study for the particular structural model. The paper demonstrates the application of the finite difference method (FDM) to determine the deflection of a stepped column, enabling a broader parametric study and analysis of a variety of solutions that satisfy the deformation criterion. The application of FDM yields a scheme convenient for coding in MATLAB while showing the dependence between the column deflection and the design parameters. The results from the finite element analysis (FEA) are in excellent agreement with those from the FDM.
- 1 January 2026
- Published by University Library in Kragujevac
- p. A51-A57
The determination of the deflection of the stepped column by the finite difference method
Besides the strength criterion, steel structures must also meet the deformation criterion, which in some cases may be critical. Excessive deformation of the structure may lead to additional loads and improper operation of the installed equipment. The most common practice in steel structure design involves using the finite element method (FEM) to calculate the stress and deformation of the current model. However, this is usually limited to the case study for the particular structural model. The paper demonstrates the application of the finite difference method (FDM) to determine the deflection of a stepped column, enabling a broader parametric study and analysis of a variety of solutions that satisfy the deformation criterion. The application of FDM yields a scheme convenient for coding in MATLAB while showing the dependence between the column deflection and the design parameters. The results from the finite element analysis (FEA) are in excellent agreement with those from the FDM.
- 23 August 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 240 (7) , 4248-4258
Determination of maximal velocity of a four-wheel forklift in a curve with constant curvature for simulation purposes
Efficiency evaluation for further optimization of existing solutions or making an efficient new solution of the material handling systems within the warehouses mainly is completed using different simulation techniques and environments. These are created by describing relevant characteristics in the process of modelling each of the system’s component. When modelling material handling devices for the performance evaluation of the material handling systems the focus is usually on kinematic characteristics as well as energy consumption. Forklifts are one of the mostly used material handling devices in warehouses and as such they are widely present in many simulation environments where their moving speed is very important parameter. The goal of this study is to determine the velocity of the forklifts in cornering situations from the perspective of quasi-static rollover, steady-state cornering and workers’ safety in the forklifts’ moving area which is essential for building more precise forklift models for simulation purposes.
- 23 August 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 240 (7) , 4248-4258
Determination of maximal velocity of a four-wheel forklift in a curve with constant curvature for simulation purposes
Efficiency evaluation for further optimization of existing solutions or making an efficient new solution of the material handling systems within the warehouses mainly is completed using different simulation techniques and environments. These are created by describing relevant characteristics in the process of modelling each of the system’s component. When modelling material handling devices for the performance evaluation of the material handling systems the focus is usually on kinematic characteristics as well as energy consumption. Forklifts are one of the mostly used material handling devices in warehouses and as such they are widely present in many simulation environments where their moving speed is very important parameter. The goal of this study is to determine the velocity of the forklifts in cornering situations from the perspective of quasi-static rollover, steady-state cornering and workers’ safety in the forklifts’ moving area which is essential for building more precise forklift models for simulation purposes.
- 1 January 2025
- Published by University Library in Kragujevac
- p. 36-43
DISCRETE EVENT SIMULATION MODEL FOR EXPECTED CYCLE TIME OF AS/RS WITH DOUBLE DEEP PALLET RACK
Automated storage and retrieval systems are widely used in highly dense tall warehouses as an important part of material handling systems, as they can efficiently reach highly positioned loads and their footprint is narrow. Their performance within the system can be evaluated using discrete event simulation techniques. The model created and described in this paper is a model of an automated storage and retrieval system working on a single and double deep pallet rack storage system. The parameters obtained through the simulation were the average single command cycle time and throughput.
- 1 January 2025
- Published by University Library in Kragujevac
- p. 36-43
DISCRETE EVENT SIMULATION MODEL FOR EXPECTED CYCLE TIME OF AS/RS WITH DOUBLE DEEP PALLET RACK
Automated storage and retrieval systems are widely used in highly dense tall warehouses as an important part of material handling systems, as they can efficiently reach highly positioned loads and their footprint is narrow. Their performance within the system can be evaluated using discrete event simulation techniques. The model created and described in this paper is a model of an automated storage and retrieval system working on a single and double deep pallet rack storage system. The parameters obtained through the simulation were the average single command cycle time and throughput.
- 31 July 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 238 (21) , 10332-10343
Cam displacement curve optimization for minimal jerk using search and rescue optimization algorithm
Polynomials of a degree higher than 8th used for the rise phase of displacement curve of a cam profile were optimized for gaining minimal jerk using the search and rescue optimization algorithm. The algorithm was used to obtain the polynomial coefficients for the polynomials of the higher degree that cannot be calculated by using the analytical approach without adding additional boundary conditions other than displacement, velocity and acceleration in characteristic positions. The degree of the polynomial from which the optimal value of jerk using the optimization algorithm can be obtained was determined, as well as the degree after which the results of the optimization give worse values of the jerk.
- 31 July 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 238 (21) , 10332-10343
Cam displacement curve optimization for minimal jerk using search and rescue optimization algorithm
Polynomials of a degree higher than 8th used for the rise phase of displacement curve of a cam profile were optimized for gaining minimal jerk using the search and rescue optimization algorithm. The algorithm was used to obtain the polynomial coefficients for the polynomials of the higher degree that cannot be calculated by using the analytical approach without adding additional boundary conditions other than displacement, velocity and acceleration in characteristic positions. The degree of the polynomial from which the optimal value of jerk using the optimization algorithm can be obtained was determined, as well as the degree after which the results of the optimization give worse values of the jerk.
- 20 July 2024
- Published by Springer Nature in International Journal of Steel Structures
- Vol. 24 (4) , 969-985
Optimization of Welded I-Girder of the Single-Beam Bridge Cranes
- 20 July 2024
- Published by Springer Nature in International Journal of Steel Structures
- Vol. 24 (4) , 969-985
Optimization of Welded I-Girder of the Single-Beam Bridge Cranes
- Open Access
- 1 January 2024
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Engineering Today
- Vol. 3 (4) , 21-32
Analysis and low-weight design of the cold-formed battened built-up column
This research presents the analysis and the low-weight optimization design of the cold-formed battened built-up column of the crane runway beam by the Marine Predators Algorithm (MPA). The objective function (the total weight of the battened built-up column) workflow uses slenderness and the geometric parameters of the channel section and batten plates as variables. This study uses the global stability of the built-up column, the buckling check of the built-up column about the material axis and non-material axis, the buckling and the strength check of the chord of the built-up column, the strength check of the batten plate of the built-up column, the strength of the batten plate's weld connections, as well as geometrical recommendations and limitations as the constraint functions. Achieved savings in column weight are between 38.66% and 51.66%, dependingly on the material and the number of batten plates of the considered example of the built-up column.
- 1 January 2024
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Engineering Today
- Vol. 3 (4) , 21-32
Open AccessAnalysis and low-weight design of the cold-formed battened built-up column
This research presents the analysis and the low-weight optimization design of the cold-formed battened built-up column of the crane runway beam by the Marine Predators Algorithm (MPA). The objective function (the total weight of the battened built-up column) workflow uses slenderness and the geometric parameters of the channel section and batten plates as variables. This study uses the global stability of the built-up column, the buckling check of the built-up column about the material axis and non-material axis, the buckling and the strength check of the chord of the built-up column, the strength check of the batten plate of the built-up column, the strength of the batten plate's weld connections, as well as geometrical recommendations and limitations as the constraint functions. Achieved savings in column weight are between 38.66% and 51.66%, dependingly on the material and the number of batten plates of the considered example of the built-up column.
- Open Access
- 1 January 2024
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Vojnotehnicki glasnik
- Vol. 72 (3) , 1345-1368
Optimal solution for the single-beam bridge crane girder using the Moth-Flame algorithm
Introduction/purpose: The paper analyses and optimizes the welded I-girder of the single-beam bridge crane with a U-profile as the top flange. This solution is to provide a lighter carrying structure, so the main goal is to minimize the weight of the main girder, i.e., the cross-sectional area while fulfiling the requirements defined by national standards and geometric constraints. Methods: The Moth-Flame Optimization (MFO) algorithm was chosen for solving this single-objective multi-criteria optimization task using MATLAB. Also, the results were verified by using the Finite Element Analysis (FEA). Results: The proposed girder shape is justified in examples of real solutions of single-beam bridge cranes and the previous research results. In this case, significant savings in the material and better results are achieved compared to the examples from the previous research. Conclusion: The proposed girder shape, methodology, the optimization algorithm and the achieved savings fully justify this research. Furthermore, this algorithm enables the application of many constraint functions, whereby the optimal values of numerous variables are obtained in a relatively short period. Therefore, it would not be possible to find the solution for that engineering task by applying analytical optimization methods.
- 1 January 2024
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Vojnotehnicki glasnik
- Vol. 72 (3) , 1345-1368
Open AccessOptimal solution for the single-beam bridge crane girder using the Moth-Flame algorithm
Introduction/purpose: The paper analyses and optimizes the welded I-girder of the single-beam bridge crane with a U-profile as the top flange. This solution is to provide a lighter carrying structure, so the main goal is to minimize the weight of the main girder, i.e., the cross-sectional area while fulfiling the requirements defined by national standards and geometric constraints. Methods: The Moth-Flame Optimization (MFO) algorithm was chosen for solving this single-objective multi-criteria optimization task using MATLAB. Also, the results were verified by using the Finite Element Analysis (FEA). Results: The proposed girder shape is justified in examples of real solutions of single-beam bridge cranes and the previous research results. In this case, significant savings in the material and better results are achieved compared to the examples from the previous research. Conclusion: The proposed girder shape, methodology, the optimization algorithm and the achieved savings fully justify this research. Furthermore, this algorithm enables the application of many constraint functions, whereby the optimal values of numerous variables are obtained in a relatively short period. Therefore, it would not be possible to find the solution for that engineering task by applying analytical optimization methods.
- Open Access
- 1 January 2024
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Engineering Today
- Vol. 3 (2) , 55-64
Comparison of fuzzy MCDM approaches in the elevator selection problem
Considering a part of the problem in the domain of vertical transport, and above all elevators, it is noticeable that there are a large number of technically feasible alternatives in most cases. The designer's task is to choose from a set of possible solutions that best match the technical and economic conditions defined by the project task. The design and appropriate MCDM technique determine the quality of the recommended decision, saving computational time without sacrificing quality in the final ranking of alternatives. The task is to choose solutions that best match the technical and economic conditions. Therefore, selecting an adequate elevator is a problem that requires the manipulation of a large number of different data and, at the same time, the inclusion of a significant number of relevant criteria and goals that can often conflict. Fuzzy logic has proven excellent in models where intuition and judgment are primary elements. This paper aims to present a systematic overview of the developed fuzzy MCDM techniques. By ranking and comparative analysis of the results, this research represents an attempt to choose a method to support decisionmaking and create a comprehensive tool in the elevator selection process.
- 1 January 2024
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Engineering Today
- Vol. 3 (2) , 55-64
Open AccessComparison of fuzzy MCDM approaches in the elevator selection problem
Considering a part of the problem in the domain of vertical transport, and above all elevators, it is noticeable that there are a large number of technically feasible alternatives in most cases. The designer's task is to choose from a set of possible solutions that best match the technical and economic conditions defined by the project task. The design and appropriate MCDM technique determine the quality of the recommended decision, saving computational time without sacrificing quality in the final ranking of alternatives. The task is to choose solutions that best match the technical and economic conditions. Therefore, selecting an adequate elevator is a problem that requires the manipulation of a large number of different data and, at the same time, the inclusion of a significant number of relevant criteria and goals that can often conflict. Fuzzy logic has proven excellent in models where intuition and judgment are primary elements. This paper aims to present a systematic overview of the developed fuzzy MCDM techniques. By ranking and comparative analysis of the results, this research represents an attempt to choose a method to support decisionmaking and create a comprehensive tool in the elevator selection process.
- 12 June 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 238 (3) , 666-676
Light-weight design of an overhead crane’s girder with a non-symmetric box cross-section
The proper choice of material and geometric properties of the girder of the bridge crane can significantly reduce its weight and production cost. This research presents the weight optimization of the main girder with a non-symmetric box-like cross-section. The strength analysis in characteristic points of the critical cross-section and the local stability of plates were conducted using Eurocodes. This study aimed to prove that a proper choice of geometry for the cross-section plates and their additional design elements can have a meaningful impact on the weight. The optimization procedure was done using Water Evaporation Optimization (WEO) algorithm, with the implementation of all necessary criteria and conditions which must be fulfilled. This study revealed that the application of the light-weight design philosophy to the structure of the main girder could significantly reduce its weight, which is verified in the existing examples of double-beam bridge cranes. Achieved savings in girder weight are between 24.43% and 34.73%, dependingly on the considered example. Also, the study showed the influence of the chosen material on the steel girder’s optimum weight and geometric parameters. Depending on the studied example of the bridge crane and selected material, the WEO algorithm gave the same solution through simulations. The value of the optimum weight had a slight deviation at the second decimal place, which is neglectable. The algorithm successfully avoided the trap of getting into the local minimum during the search. In the end, it can be stated that the application of the WEO algorithm was successful in the considered engineering problem since it was the optimization of a complex steel structure with 11 variables and more than 20 constraint functions.
- 12 June 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 238 (3) , 666-676
Light-weight design of an overhead crane’s girder with a non-symmetric box cross-section
The proper choice of material and geometric properties of the girder of the bridge crane can significantly reduce its weight and production cost. This research presents the weight optimization of the main girder with a non-symmetric box-like cross-section. The strength analysis in characteristic points of the critical cross-section and the local stability of plates were conducted using Eurocodes. This study aimed to prove that a proper choice of geometry for the cross-section plates and their additional design elements can have a meaningful impact on the weight. The optimization procedure was done using Water Evaporation Optimization (WEO) algorithm, with the implementation of all necessary criteria and conditions which must be fulfilled. This study revealed that the application of the light-weight design philosophy to the structure of the main girder could significantly reduce its weight, which is verified in the existing examples of double-beam bridge cranes. Achieved savings in girder weight are between 24.43% and 34.73%, dependingly on the considered example. Also, the study showed the influence of the chosen material on the steel girder’s optimum weight and geometric parameters. Depending on the studied example of the bridge crane and selected material, the WEO algorithm gave the same solution through simulations. The value of the optimum weight had a slight deviation at the second decimal place, which is neglectable. The algorithm successfully avoided the trap of getting into the local minimum during the search. In the end, it can be stated that the application of the WEO algorithm was successful in the considered engineering problem since it was the optimization of a complex steel structure with 11 variables and more than 20 constraint functions.
- Open Access
- 1 February 2020
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 27 (1) , 12-19
Modified PROMETHEE Approach for Solving Multi-Criteria Location Problems with Complex Criteria Functions
The specific problem that occurs in multi-criteria decision-making (MCDM) processes is ranking a number of alternatives using complex criteria functions (the hierarchical structure of criteria) whose values must consider the impacts of...
- 1 February 2020
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 27 (1) , 12-19
Open AccessModified PROMETHEE Approach for Solving Multi-Criteria Location Problems with Complex Criteria Functions
The specific problem that occurs in multi-criteria decision-making (MCDM) processes is ranking a number of alternatives using complex criteria functions (the hierarchical structure of criteria) whose values must consider the impacts of...