Jiri Svarny
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jiri Svarny has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Ivan Duran
Institute of Plasma Physics of the CAS
1 shared publication - Jan Reboun
University of West Bohemia
1 shared publication - Jaroslav Soltes
Centrum výzkumu Řež s.r.o
1 shared publication - Ladislav Viererbl
Centrum výzkumu Řež s.r.o
1 shared publication - Lukas Sobotka
University of West Bohemia
1 shared publication - Ondrej Ruzicka
Faculty of Electrical Engineering, University of West Bohemia, Univerzitní 8, 301 00 Pilsen, Czech Republic
1 shared publication
Latest Publications
- Open Access
- 1 August 2026
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 68 (8) , 085015
TPC magnetic field sensors for fusion reactors: instrumented neutron irradiation test
Future thermonuclear fusion reactors will impose extreme demands on diagnostic components, particularly regarding radiation hardness, high-temperature tolerance and reliability, with limited or no opportunities for maintenance or replacement. Innovative, thoroughly tested and qualified solutions are crucial to meet these challenges. The exploitation of thick-printed copper (TPC) technology has recently enabled the development of compact and efficient inductive and steady-state magnetic field sensors. TPC coils, with an optimized winding arrangement designed to minimize cross-field sensitivity and reduce temperature gradient-induced spurious voltages, have been extensively tested, including exposure to high neutron fluence during instrumented neutron irradiation tests up to 0.5 dpa at the LVR-15 fission reactor. This contribution will describe these novel design solutions and present the findings of comprehensive testing. Data analysis of resistance measurements including temperature and irradiation models are presented in this paper.
- 1 August 2026
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 68 (8) , 085015
Open AccessTPC magnetic field sensors for fusion reactors: instrumented neutron irradiation test
Future thermonuclear fusion reactors will impose extreme demands on diagnostic components, particularly regarding radiation hardness, high-temperature tolerance and reliability, with limited or no opportunities for maintenance or replacement. Innovative, thoroughly tested and qualified solutions are crucial to meet these challenges. The exploitation of thick-printed copper (TPC) technology has recently enabled the development of compact and efficient inductive and steady-state magnetic field sensors. TPC coils, with an optimized winding arrangement designed to minimize cross-field sensitivity and reduce temperature gradient-induced spurious voltages, have been extensively tested, including exposure to high neutron fluence during instrumented neutron irradiation tests up to 0.5 dpa at the LVR-15 fission reactor. This contribution will describe these novel design solutions and present the findings of comprehensive testing. Data analysis of resistance measurements including temperature and irradiation models are presented in this paper.
- Open Access
- 31 March 2026
- Published by MDPI AG in Electronics
- Vol. 15 (7) , 1451
Air-Core PCB Toroid for Switching Converters: Design and Comparison with Other Inductor Topologies
This study examines the design, manufacturing, and testing of planar PCB inductors (spiral and toroid), including multilayer PCB toroid configurations. These inductors are intended for environments with strong magnetic fields, such as high-energy physics experiments and medical applications, where traditional inductors with ferromagnetic cores are unsuitable. Twelve inductor samples were manufactured and tested. The focus was on maximizing inductance and evaluating performance in a high-frequency DC-DC step-down converter. Key parameters measured included inductance, resistance, thermal performance, electromagnetic interference (EMI), and frequency-dependent behavior in multilayer PCB implementations. The results showed that planar spiral inductors handled higher currents and achieved better efficiency, reaching up to 74.86%. Planar toroid inductors were more tolerant of added shielding, maintaining their inductance, while multilayer toroid designs exhibited reduced DC resistance but increased frequency dependence and sensitivity to parasitic effects. Overall, planar inductors were found to be viable for applications where ferromagnetic cores are unsuitable. Further optimization of geometry, layer configuration, and manufacturing processes could enhance their performance.
- 31 March 2026
- Published by MDPI AG in Electronics
- Vol. 15 (7) , 1451
Open AccessAir-Core PCB Toroid for Switching Converters: Design and Comparison with Other Inductor Topologies
This study examines the design, manufacturing, and testing of planar PCB inductors (spiral and toroid), including multilayer PCB toroid configurations. These inductors are intended for environments with strong magnetic fields, such as high-energy physics experiments and medical applications, where traditional inductors with ferromagnetic cores are unsuitable. Twelve inductor samples were manufactured and tested. The focus was on maximizing inductance and evaluating performance in a high-frequency DC-DC step-down converter. Key parameters measured included inductance, resistance, thermal performance, electromagnetic interference (EMI), and frequency-dependent behavior in multilayer PCB implementations. The results showed that planar spiral inductors handled higher currents and achieved better efficiency, reaching up to 74.86%. Planar toroid inductors were more tolerant of added shielding, maintaining their inductance, while multilayer toroid designs exhibited reduced DC resistance but increased frequency dependence and sensitivity to parasitic effects. Overall, planar inductors were found to be viable for applications where ferromagnetic cores are unsuitable. Further optimization of geometry, layer configuration, and manufacturing processes could enhance their performance.
- 26 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 40 (3) , 720-727
Model-Based Bias Controller for a Mach-Zehnder Intensity Modulator
A new dither technique is presented to control the bias voltage of an intensity modulator of the Mach-Zehnder type to maintain the quadrature operating point. This method is based on the direct calculation of the operating point deviation. The calculation uses an exact mathematical model of the modulator. The data used for calculating the deviation value are obtained from an analysis based on a fast Fourier transform with a properly set level of vector averaging. Unlike other solutions, the proposed feedback system does not use an approach with a proportional-integral or proportional-integral-derivative controller. Moreover, the presented stabilization method is robust and invariant regarding changes in the input optical power of the modulator and immune to prospective fluctuations of most of the feedback loop parameters. With the proposed approach in its present form, a 3-hour stability of ±0.08° is achieved. This value reflects the limitations of the equipment used. Even better results can be expected using more powerful hardware.
- 26 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 40 (3) , 720-727
Model-Based Bias Controller for a Mach-Zehnder Intensity Modulator
A new dither technique is presented to control the bias voltage of an intensity modulator of the Mach-Zehnder type to maintain the quadrature operating point. This method is based on the direct calculation of the operating point deviation. The calculation uses an exact mathematical model of the modulator. The data used for calculating the deviation value are obtained from an analysis based on a fast Fourier transform with a properly set level of vector averaging. Unlike other solutions, the proposed feedback system does not use an approach with a proportional-integral or proportional-integral-derivative controller. Moreover, the presented stabilization method is robust and invariant regarding changes in the input optical power of the modulator and immune to prospective fluctuations of most of the feedback loop parameters. With the proposed approach in its present form, a 3-hour stability of ±0.08° is achieved. This value reflects the limitations of the equipment used. Even better results can be expected using more powerful hardware.
- Open Access
- 6 November 2020
- Published by Polish Academy of Sciences Chancellery in Archives of Electrical Engineering
- Vol. 69 (4) , 781-792
Reliable digital dead-time generator for the GaN HEMTs based H-bridge converters
The paper deals with hardware solution of a fully digital dead-time generator. The circuit is applicable to the H-bridges based on any type of semiconductor switching devices including SiC, IGBT, Si-MOSFET and up-to-date GaN HEMTs. The generation of dead-times is ensured by commercially available silicon delay lines. High temperature stability is obtained by self-compensation of propagation delay of logic elements thanks to the symmetry of design topology. The circuit can be set-up to generate dead-times in the range from 10 ns to 500 ns. Longer dead-times are also available by simple cascading of the silicon delay lines. The key motivation for development of the circuit was unavailability of ready to use integrated solutions on the market. Moreover, contrary to the other solutions the proposed circuit is immune to prospective oscillations of an input PWM signal. The paper brings a detailed analysis of the circuit principle, results of the verification of a sample solution and an example of practical application as well.
- 6 November 2020
- Published by Polish Academy of Sciences Chancellery in Archives of Electrical Engineering
- Vol. 69 (4) , 781-792
Open AccessReliable digital dead-time generator for the GaN HEMTs based H-bridge converters
The paper deals with hardware solution of a fully digital dead-time generator. The circuit is applicable to the H-bridges based on any type of semiconductor switching devices including SiC, IGBT, Si-MOSFET and up-to-date GaN HEMTs. The generation of dead-times is ensured by commercially available silicon delay lines. High temperature stability is obtained by self-compensation of propagation delay of logic elements thanks to the symmetry of design topology. The circuit can be set-up to generate dead-times in the range from 10 ns to 500 ns. Longer dead-times are also available by simple cascading of the silicon delay lines. The key motivation for development of the circuit was unavailability of ready to use integrated solutions on the market. Moreover, contrary to the other solutions the proposed circuit is immune to prospective oscillations of an input PWM signal. The paper brings a detailed analysis of the circuit principle, results of the verification of a sample solution and an example of practical application as well.
- 1 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Laboratory Fixture for Measurement of Dielectric Absorption of Capacitors
Dielectric absorption is known as one of the capacitors parasitic effects. Underestimation of the phenomena can have frustrating consequences starting from unexpected behavior of the circuits through the damage or malfunction of the sensitive electronics up to the eventuality of shock hazard to the device's operator. The paper presents a new and alternative method to test the phenomenon. Contrary to the traditional approach the method is based on discharging of capacitor using various loads. To implement the method there was designed and implemented a specialized measuring fixture. The paper describes a principle of the method, a principle of the measuring fixture and practical results as well.
- 1 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Laboratory Fixture for Measurement of Dielectric Absorption of Capacitors
Dielectric absorption is known as one of the capacitors parasitic effects. Underestimation of the phenomena can have frustrating consequences starting from unexpected behavior of the circuits through the damage or malfunction of the sensitive electronics up to the eventuality of shock hazard to the device's operator. The paper presents a new and alternative method to test the phenomenon. Contrary to the traditional approach the method is based on discharging of capacitor using various loads. To implement the method there was designed and implemented a specialized measuring fixture. The paper describes a principle of the method, a principle of the measuring fixture and practical results as well.
- Open Access
- 1 June 2018
- Published by Walter de Gruyter GmbH in Journal of Electrical Engineering
- Vol. 69 (3) , 212-218
Emulator of harmonic distortion of bias port of the mach-zehnder intensity modulator
The paper deals with the design of an analog circuit to substitute the role of a real intensity Mach-Zehnder modulator for the preliminary tuning of bias controllers. The proposed circuit has similar harmonic distortion as an electro-optic modulator biased around the quadrature operating point. The designed device utilizes a shaping circuit based on a differential pair of bipolar junction transistors. The harmonic distortion of both the Mach-Zehnder intensity modulator and the differential amplifier are analysed. A method to design the emulating circuit of desired features is described and explained and a the comparison of the measured results to the theory is presented.
- 1 June 2018
- Published by Walter de Gruyter GmbH in Journal of Electrical Engineering
- Vol. 69 (3) , 212-218
Open AccessEmulator of harmonic distortion of bias port of the mach-zehnder intensity modulator
The paper deals with the design of an analog circuit to substitute the role of a real intensity Mach-Zehnder modulator for the preliminary tuning of bias controllers. The proposed circuit has similar harmonic distortion as an electro-optic modulator biased around the quadrature operating point. The designed device utilizes a shaping circuit based on a differential pair of bipolar junction transistors. The harmonic distortion of both the Mach-Zehnder intensity modulator and the differential amplifier are analysed. A method to design the emulating circuit of desired features is described and explained and a the comparison of the measured results to the theory is presented.
- Open Access
- 16 January 2016
- Published by International Science and Engineering Society in International Journal of Advances in Telecommunications, Electrotechnics, Signals and Systems
- Vol. 5 (1) , 44-52
Wideband Analog Transmission System Based on the External Intensity Electro-Optic Modulator
The work deals with design and integration of an analog electro-optic transmission system suitable for some specialized tasks of diagnostics and measurements. The system is based on principle of external intensity modulation of fiber guided laser radiation. Besides wideband and almost lossless transmission the system tolerates extreme length of the transmitting medium and ensures ultimate galvanic barrier between the input and output.
- 16 January 2016
- Published by International Science and Engineering Society in International Journal of Advances in Telecommunications, Electrotechnics, Signals and Systems
- Vol. 5 (1) , 44-52
Open AccessWideband Analog Transmission System Based on the External Intensity Electro-Optic Modulator
The work deals with design and integration of an analog electro-optic transmission system suitable for some specialized tasks of diagnostics and measurements. The system is based on principle of external intensity modulation of fiber guided laser radiation. Besides wideband and almost lossless transmission the system tolerates extreme length of the transmitting medium and ensures ultimate galvanic barrier between the input and output.
- 1 July 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1 2002, 330-334
Broadband analog electro-optic transmission system with the ultimate galvanic isolation capability
The work deals with design and integration of an analog electro-optic transmission system suitable for some specialized tasks of diagnostics and measurements. The system is based on principle of external intensity modulation of fiber guided laser radiation. Besides wideband and almost lossless transmission the system tolerates extreme length of the transmitting medium and ensures ultimate galvanic barrier between the input and output.
- 1 July 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1 2002, 330-334
Broadband analog electro-optic transmission system with the ultimate galvanic isolation capability
The work deals with design and integration of an analog electro-optic transmission system suitable for some specialized tasks of diagnostics and measurements. The system is based on principle of external intensity modulation of fiber guided laser radiation. Besides wideband and almost lossless transmission the system tolerates extreme length of the transmitting medium and ensures ultimate galvanic barrier between the input and output.
- 1 July 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 227-230
Specialized compact external electro-optic modulating unit
As a vital part of specialized electro-optic transmission system a broadband external modulating unit was designed and developed. The unit is based on an integrated intensity modulator of Mach-Zehnder type. Paper deals with design of auxiliary circuitry of the modulator and its implementation in order to achieve desired functionality. Solution of a broadband driver, original - manually adjustable bias controller and a power supply of the unit is presented here. Integration of all the circuits together makes the final hardware compact and unique as well.
- 1 July 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 227-230
Specialized compact external electro-optic modulating unit
As a vital part of specialized electro-optic transmission system a broadband external modulating unit was designed and developed. The unit is based on an integrated intensity modulator of Mach-Zehnder type. Paper deals with design of auxiliary circuitry of the modulator and its implementation in order to achieve desired functionality. Solution of a broadband driver, original - manually adjustable bias controller and a power supply of the unit is presented here. Integration of all the circuits together makes the final hardware compact and unique as well.
- 1 October 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 17363705,p. 133-136
Implementation of a precise quadrature point bias controller to the integrated intensity electro-optic modulator
A broadband electro-optic modulating unit forms a key part of a specialized transmission system for needs of measurements. The modulating unit is based on an integrated analog intensity modulator of Mach-Zehnder type. A proper adjustment of modulator operating point significantly affects performance of the modulator and consequently of the whole transmission system as well. The paper deals with design and implementation of a specialized driver - a bias circuit for extremely precise set-up of optimal operating point of the modulator. The driver operates on principle of suppression of second harmonic component detected at the modulator output during excitation of bias port with a low-frequency harmonic signal.
- 1 October 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 17363705,p. 133-136
Implementation of a precise quadrature point bias controller to the integrated intensity electro-optic modulator
A broadband electro-optic modulating unit forms a key part of a specialized transmission system for needs of measurements. The modulating unit is based on an integrated analog intensity modulator of Mach-Zehnder type. A proper adjustment of modulator operating point significantly affects performance of the modulator and consequently of the whole transmission system as well. The paper deals with design and implementation of a specialized driver - a bias circuit for extremely precise set-up of optimal operating point of the modulator. The driver operates on principle of suppression of second harmonic component detected at the modulator output during excitation of bias port with a low-frequency harmonic signal.