Martin Correns
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Martin Correns has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Marcel Bartz
Department of Mechanical Engineering, Friedrich-Alexander-Universität Erlangen-Nürnberg (FAU), Engineering Design, Martensstraße 9, 91058 Erlangen, Germany
1 shared publication - Markus Dinkel
Materials Technology, Schaeffler Technologies 1 , Industriestr. 3, 91074Herzogenaurach, DE
1 shared publication - Michael Juettner
Department of Mechanical Engineering, Friedrich-Alexander-Universität Erlangen-Nürnberg (FAU), Engineering Design, Martensstraße 9, 91058 Erlangen, Germany
1 shared publication Michael Warmuth
Bearing Validation, Schaeffler Technologies 3 , Georg Schaefer Str. 30, 97421Schweinfurt, DE
1 shared publication- Sandro Wartzack
Engineering Design, Friedrich-Alexander-Universität Erlangen-Nürnberg, 91058 Erlangen, Germany
1 shared publication - Stephan Tremmel
Engineering Design and CAD, University of Bayreuth, Universitätsstraße 30, 95447 Bayreuth, Germany
1 shared publication
Latest Publications
- Open Access
- 1 June 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (6) , 107
Edge Pressures Obtained Using FEM and Half-Space: A Study of Truncated Contact Ellipses
In rolling or gear contacts, truncation of the contact ellipse can occur, for example, when an undercut extends into the contact area. For an elastic calculation approach, the edge constitutes a mathematical singularity, which is revealed by a theoretically infinitely high pressure peak. However, when elastic–plastic material behavior is taken into account, the pressure peak is limited by local hardening and yielding of the material, leading to plastic deformations. As a result, those calculations are rather challenging and the results partly unexpected due to the discontinuity contained in the geometry. Nevertheless, to the authors’ knowledge, hardly any published studies exist on elastic–plastic simulations of truncated contact ellipses. Therefore, a numerical study concerning the contact of a rigid ball with an elastic–plastic plane is presented. Due to an undercut in the plane, a quarter of the theoretical Hertzian contact ellipse is cut off. The aim of the study is to investigate the influence of the undercut angle on the pressure distribution and the elastic and plastic deformation at the edge. The use of FEM shows that the undercut angle has a significant effect on the characteristics of the contact. The results obtained using FEM are then used as a reference for comparison with a semi-analytical method (SAM). It is shown that the SAM, based on the half-space, provides comparable results only for very small undercut angles.
- 1 June 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (6) , 107
Open AccessEdge Pressures Obtained Using FEM and Half-Space: A Study of Truncated Contact Ellipses
In rolling or gear contacts, truncation of the contact ellipse can occur, for example, when an undercut extends into the contact area. For an elastic calculation approach, the edge constitutes a mathematical singularity, which is revealed by a theoretically infinitely high pressure peak. However, when elastic–plastic material behavior is taken into account, the pressure peak is limited by local hardening and yielding of the material, leading to plastic deformations. As a result, those calculations are rather challenging and the results partly unexpected due to the discontinuity contained in the geometry. Nevertheless, to the authors’ knowledge, hardly any published studies exist on elastic–plastic simulations of truncated contact ellipses. Therefore, a numerical study concerning the contact of a rigid ball with an elastic–plastic plane is presented. Due to an undercut in the plane, a quarter of the theoretical Hertzian contact ellipse is cut off. The aim of the study is to investigate the influence of the undercut angle on the pressure distribution and the elastic and plastic deformation at the edge. The use of FEM shows that the undercut angle has a significant effect on the characteristics of the contact. The results obtained using FEM are then used as a reference for comparison with a semi-analytical method (SAM). It is shown that the SAM, based on the half-space, provides comparable results only for very small undercut angles.
- 1 August 2020
- Published by ASTM International
- p. 147-168
Surface Damage in Rolling Bearings and the Impact on Rolling Contact Fatigue
Ideally, rolling bearings would always be operated in controlled clean environments and with perfect mounting conditions. However, in many cases, contamination as well as impact damage during mounting occurs. This can result in damage to the bearing raceways due to overrolling of particulate matter or uncontrolled contact of mating surfaces. The influence of such surface deformations on the bearing fatigue life has long been and still is a topic of research for bearing suppliers as well as for customers. In this work, the effect has been studied by a stringent simulation approach starting from the initial material deformation mechanisms to fatigue simulation and subsequent rating life analysis. Two-dimensional as well as three-dimensional deformation simulations were applied to identify the stress and strain formation during initial indentation and subsequent overrolling of damage features in the raceway of bearing rings. The evolution of stress and strain states were simulated for multiple overrolling events until saturation occurred. Subsequently, the resulting stress fields were analyzed in a local-stress-based rating life model. Several shapes and sizes of predamage were modeled, and the effect on the calculated lifetime was compared. This simulative approach was accompanied by experimental validation on artificially predamaged bearing raceways to compare calculated rating life with experimental test life data. It can be shown that the size, shape, and curvature of the damages are not necessarily dominant factors for the effect of indentations on bearing life. The most dominant factor proves to be the size of the material ridge formed due to the material flow at the indent. For the testing conditions and size of the tested bearings, a threshold for the life-limiting ridge heights could be derived from simulations, which was found to be in good agreement with results from the life tests.
- 1 August 2020
- Published by ASTM International
- p. 147-168
Surface Damage in Rolling Bearings and the Impact on Rolling Contact Fatigue
Ideally, rolling bearings would always be operated in controlled clean environments and with perfect mounting conditions. However, in many cases, contamination as well as impact damage during mounting occurs. This can result in damage to the bearing raceways due to overrolling of particulate matter or uncontrolled contact of mating surfaces. The influence of such surface deformations on the bearing fatigue life has long been and still is a topic of research for bearing suppliers as well as for customers. In this work, the effect has been studied by a stringent simulation approach starting from the initial material deformation mechanisms to fatigue simulation and subsequent rating life analysis. Two-dimensional as well as three-dimensional deformation simulations were applied to identify the stress and strain formation during initial indentation and subsequent overrolling of damage features in the raceway of bearing rings. The evolution of stress and strain states were simulated for multiple overrolling events until saturation occurred. Subsequently, the resulting stress fields were analyzed in a local-stress-based rating life model. Several shapes and sizes of predamage were modeled, and the effect on the calculated lifetime was compared. This simulative approach was accompanied by experimental validation on artificially predamaged bearing raceways to compare calculated rating life with experimental test life data. It can be shown that the size, shape, and curvature of the damages are not necessarily dominant factors for the effect of indentations on bearing life. The most dominant factor proves to be the size of the material ridge formed due to the material flow at the indent. For the testing conditions and size of the tested bearings, a threshold for the life-limiting ridge heights could be derived from simulations, which was found to be in good agreement with results from the life tests.