Euan J. Bain
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Euan J. Bain has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Joseph M. Calo
School of Engineering, Brown University, Providence, Rhode Island 02912, United States
3 shared publications Johannes Kirchner
School of Engineering, Brown University, Providence, RI 02912, United States
2 shared publicationsElizabeth DiCocco
1 shared publicationFlorian M Zehentbauer
University of Aberdeen
1 shared publicationJenny Axén
Division of Engineering, Box D, Brown University, Providence, Rhode Island 02912
1 shared publication- Johannes Kiefer
Technische Thermodynamik, University of Bremen, Badgasteiner Str. 1, 28359 Bremen, Germany
1 shared publication
Latest Publications
- 8 March 2013
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 27 (3) , 1712-1719
Development of a Low Temperature, Molten Hydroxide Direct Carbon Fuel Cell
- 8 March 2013
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 27 (3) , 1712-1719
Development of a Low Temperature, Molten Hydroxide Direct Carbon Fuel Cell
- 1 May 2012
- Published by Elsevier in Chemical Engineering Journal
- Vol. 189-190, 237-243
Arsenic removal via ZVI in a hybrid spouted vessel/fixed bed filter system
- 1 May 2012
- Published by Elsevier in Chemical Engineering Journal
- Vol. 189-190, 237-243
Arsenic removal via ZVI in a hybrid spouted vessel/fixed bed filter system
- 27 February 2012
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 23 (4)
Multiple parameter monitoring in a direct methanol fuel cell
- 27 February 2012
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 23 (4)
Multiple parameter monitoring in a direct methanol fuel cell
- 15 March 2010
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 24 (6) , 3415-3421
Electrosorption/Electrodesorption of Arsenic on a Granular Activated Carbon in the Presence of Other Heavy Metals
The adsorption, electrosorption, and electrodesorption of aqueous, inorganic arsenic on the granular activated carbon (GAC), DARCO 12 × 20 (Darco 1220) GAC, were investigated in solutions containing arsenic as the only contaminant, as well as with chromium, nickel, and iron. Darco 1220 was selected for these investigations primarily because it is relatively ineffective as a normal (unassisted) arsenic adsorbent in the chosen electrolytes at the low loadings used. It is shown that the application of anodic potentials in the 1.0−1.5 V range, however, result in enhanced uptake, most likely because of charging of the electrochemical double layer at the electrode surface. Regeneration (100%) of electrosorbed arsenic was achieved via electrodesorption at a cathodic potential of 1.50 V. The presence of metal ad ions was observed to have a significant and complex effect on arsenic adsorption, electrosorption, and electrodesorption. In particular, the Cr/As ratio was shown to have complex effects, decreasing adsorption uptake when present as 3:2 but enhancing adsorption when present as 5:1. Nickel was found to have less of an effect than chromium, except at the highest anodic potential used of 1.50 V, where it exhibited better performance than chromium. The presence of iron significantly enhanced uptake. With a 1.50 V anodic potential, the bulk arsenic concentration was reduced to less than detectable limits, well below the United States Environmental Protection Agency (U.S. EPA) maximum contaminant level (MCL) for drinking water. Regeneration efficiency by electrodesorption for the As−Fe system was greater than about 90%.
- 15 March 2010
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 24 (6) , 3415-3421
Electrosorption/Electrodesorption of Arsenic on a Granular Activated Carbon in the Presence of Other Heavy Metals
The adsorption, electrosorption, and electrodesorption of aqueous, inorganic arsenic on the granular activated carbon (GAC), DARCO 12 × 20 (Darco 1220) GAC, were investigated in solutions containing arsenic as the only contaminant, as well as with chromium, nickel, and iron. Darco 1220 was selected for these investigations primarily because it is relatively ineffective as a normal (unassisted) arsenic adsorbent in the chosen electrolytes at the low loadings used. It is shown that the application of anodic potentials in the 1.0−1.5 V range, however, result in enhanced uptake, most likely because of charging of the electrochemical double layer at the electrode surface. Regeneration (100%) of electrosorbed arsenic was achieved via electrodesorption at a cathodic potential of 1.50 V. The presence of metal ad ions was observed to have a significant and complex effect on arsenic adsorption, electrosorption, and electrodesorption. In particular, the Cr/As ratio was shown to have complex effects, decreasing adsorption uptake when present as 3:2 but enhancing adsorption when present as 5:1. Nickel was found to have less of an effect than chromium, except at the highest anodic potential used of 1.50 V, where it exhibited better performance than chromium. The presence of iron significantly enhanced uptake. With a 1.50 V anodic potential, the bulk arsenic concentration was reduced to less than detectable limits, well below the United States Environmental Protection Agency (U.S. EPA) maximum contaminant level (MCL) for drinking water. Regeneration efficiency by electrodesorption for the As−Fe system was greater than about 90%.
- Top Cited Papers
- 1 December 2008
- Published by Elsevier in Energy Policy
- Vol. 36 (12) , 4352-4355
Energy-storage technologies and electricity generation
- 1 December 2008
- Published by Elsevier in Energy Policy
- Vol. 36 (12) , 4352-4355
Top Cited PapersEnergy-storage technologies and electricity generation