HRH. V. Rusakova

H. V. Rusakova

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


H. V. Rusakova has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • The Micromechanical Properties of CoCrFeNiMnVx (х = 0-2) High-Entropy Alloys

    by Hanna Rusakova, Larysa Fomenko, Serzh Lubenets, Mykhailo Tikhonovsky, Igor Kislyak, Elena Tabachnikova, Yi Huang, Terence G. Langdon

    The microhardness of CoCrFeNiMnV x (х = 0-2) high-entropy alloys (HEAs) was measured in the temperature range 77-293 K. At x ≤ 0.4, a significant monotonic increase in microhardness occurs with decreasing temperature, which indicates the thermally-activated character of plastic deformation of the material under the indenter. At x = 0.5, as well as at x = 0.75 and 0.85, athermal behavior of microhardness was detected in the ranges of 200-293 K and 150-293 K, respectively. The latter is apparently associated with the appearance in the indicated alloys, along with the FCC phase, of precipitates of the hard intermetallic sigma phase, which are athermal obstacles to the motion of dislocations. For the first time the microhardness of the sigma phase in the range of 77-293 K was measured; at 293 K and 77 K it was about 9.5 GPa and 12.5 GPa, respectively, which is approximately 5 times higher than the microhardness of the FCC alloy with x = 0.25.

  • Normal and reverse indentation size effects in annealed and highly deformed metals

    by S. V. Lubenets, L. S. Fomenko, H. V. Rusakova

    The normal and reverse indentation size effects for annealed and highly deformed Al, Al–Li alloy, Cu, and titanium VT1-0 were investigated. The normal indentation size effect (ISE) was revealed in all metals studied at large indentation depths. This behavior can only partially be described using the Nix and Gao model (NG) to interpret the depth-dependent hardness. The Feng and Nix correction to the NG model for small indentation depths works well for annealed coarse-grained (CG) metals. To explain the observed hardness dependence on the indentation depth, it is necessary to take into account the structure state of the surface layer. Grinding and mechanical polish of annealed fcc metals, such as aluminum, create a work-hardened layer that has higher hardness value compared to an electropolished sample as the load decreases and hence more pronounced ISE. Mechanical treatment of surfaces resulted in work-hardening of the thin layer in annealed CG metals and softening in naturally hard, ultrafine-grained, nano-crystalline, and hardening metals, changing the mechanical response of the metal at tension and contact deformation. In metals subjected to heavy plastic deformation, we first observed the reverse indentation size effect (RISE) phenomena where microhardness decreases with decreasing applied load.

  • Description of the tension kinetics of amorphous and amorphous-crystalline polymers under conditions of moderate and deep cooling by the common nonlinear rheological equation

    by V. D. Natsik, H. V. Rusakova, V. A. Lototskaya

    The comparative analysis of the results of low-temperature mechanical tests of the samples of amorphous and amorphous-crystalline polyimide of the Kapton H type was carried out. In the experiments [East Eur. J. Phys., No. 4, 144 (2020)], tensile diagrams σ(ɛ;T,ε˙) of such samples were recorded, namely, the dependences of the deforming stress on the strain ɛ = ε˙t at constant values of the strain rate ε˙ = 7⋅10–5, 7⋅10–4, 6⋅10–3 s–1, and temperature T = 293, 77, and 4.2 K. The initial aim of these experiments was to study the effect of moderate (77 K) and deep (4.2 K) cooling on the structure and some mechanical characteristics of polyimide, important for its use in cryogenic and aerospace engineering. Later (Low Temp. Phys. 49, 521 (2023) [Fiz. Nyzk. Temp. 49, 569 (2023)]), there was a need and opportunity to supplement the experimental results with additional analysis in order to use them to test new aspects of the theory of low-temperature elastic-viscous deformation of polymers, in particular, the description of the effects of forced elasticity and their competition with brittle fracture processes. A detailed comparison of the tensile diagrams of the polyimide samples with amorphous and amorphous-crystalline mole­cular structures performed in this study showed that at T = 293 K both structures have clearly pronounced pro­perties of the elastomers, namely, the rubber-like materials with high elasticity and the ability to reversible deformation. It has been established that amorphous samples retain these properties up to deep cooling at T = 4.2 K, and amorphous-crystalline ones only to a state of moderate cooling: at T < 77 K they acquire the properties of glassy materials with brittle fracture at the initial stage of elastic deformation. It is also shown that the kinetics of highly elastic deformation of polyimide with molecular structures of both types is due to the thermomechanical activation of soliton-like elaston excitations on molecular chains in the amorphous component of the material and is described by a nonlinear rheological equation derived earlier for the molecular model of an amorphous polymer: Low Temp. Phys. 48, 253 (2022) [Fiz. Nyzk. Temp. 48, 281 (2022)], Low Temp. Phys. 49, 228 (2023) [Fiz. Nyzk. Temp. 49, 246 (2023)]. By comparing the results of experiments and theory, an analytical description of the tension diagrams σ(ɛ;T,ε˙) of polyimide samples with molecular structures of both types was obtained, as well as empirical estimates of their rheological characteristics and microscopic parameters of elaston excitations. During low-temperature deformation of a polymer with a mixed structure, rigid crystalline fibrils immersed in the softer amorphous medium undergo only minor elastic deformations, but significantly increase the intensity of elaston activation and fracture processes in the amorphous component. Upon cooling, this leads to the convergence of critical stresses of highly elastic relaxation and fracture and to the transformation of an elastomer with such a structure into a glassy brittle material.

  • Open Access

    Nonlinear effects at the deformation of amorphous polymers in warm and frozen states

    by V. D. Natsik, H. V. Rusakova

    One of the important problems of the modern rheology of polymer materials, namely, the possibility of describing the deformation of amorphous polymers within the framework of linear rheological relationships between relative deformation and deforming stress or the need to use nonlinear rheological equations is considered. The criteria for distinguishing these approaches, namely, the determination of the corresponding critical values of the macro- and microphysical characteristics of the material and the conditions for carrying out the mechanical tests are also discussed. In particular, the difference between the influence of kinetic and thermodynamic nonlinear effects on the regularities of deformation processes of amorphous polymers in warm and frozen states was noted. The influence of nonlinear effects on the general shape and characteristics of individual stages of the “relative strain - deforming stress” diagram at deformation of polymer samples with specified values of strain rate and temperature is analyzed in detail. The results of the theoretical analysis were used for the physical interpretation of the general form and features of individual stages of the tensile test diagrams of amorphous polyimide films (V. D. Natsik, H. V. Rusakova, S. V. Lubenets, V. A. Lototskaya, and L. F. Yakovenko, Fiz. Nyzk. Temp. 49, 569 (2023) [Low Temp. Phys. 49, 521 (2023)]), empirical estimates for the rheological characteristics of this polymer were obtained.


  • Low-temperature elasticity of amorphous polymers: Molecular model and rheological equation

    by V. D. Natsik, H. V. Rusakova

    A molecular-kinetic model of the processes of highly elastic deformation of amorphous polymers is proposed and, on its basis, nonlinear rheological equations are obtained; these latter make it possible to describe these processes under changes of deformation conditions in a wide range: temperature, deforming stress, and strain rate. A connection of the nonlinear micromechanical model of a polymer with the classical macromechanical model of a standard linear body is established. The transitions between the structural-deformation states of a warm and frozen elastomer, as well as the effects of low-temperature deformation melting and quantum elasticity of an amorphous polymer, are discussed.


  • Low temperature micromechanical properties of nanocrystalline CoCrFeNiMn high entropy alloy

    by H.V. Rusakova, L.S. Fomenko, S.N. Smirnov, A.V. Podolskiy, Y.O. Shapovalov, E.D. Tabachnikova, M.A. Tikhonovsky, A.V. Levenets, M.J. Zehetbauer, E. Schafler


  • Nanoindentation of pure and gas-saturated fullerite C60 crystals: Elastic-to-plastic transition, hardness, elastic modulus

    by S. N. Dub, G. N. Tolmachova, S. V. Lubenets, L. S. Fomenko, H. V. Rusakova

    Elastic-plastic transition at nanoindentation of (111) plane of pure C60 fullerite single crystals was studied. The onset of plastic deformation in the contact was noted due to the plateau formation in the initial part of loading curve. The estimated stress of plasticity beginning was found to be on the order of the theoretical shear stress required for homogeneous dislocation nucleation in the ideal crystal lattice of C60. The empirical values of elastic modulus E ∼ 13.5 GPa, hardness of the ideal crystal lattice H ∼ 1.4 GPa, and hardness at different indentation loads were obtained. The hardness vs load dependence was found consistent with the model of geometrically necessary dislocations. The loading diagrams shape and the dependencies of contact pressure vs indentation depth were strongly affected by gaseous interstitial impurities (hydrogen, oxygen, nitrogen) in C60 crystal; transition stress was essentially less and plateaus formation was observed at elevated indentation loads and depths as compared with pure fullerite crystal. For crystals, saturated with hydrogen, the enhanced value of elastic modulus (∼ 20.4 GPa) and hardness (∼ 1.1 GPa) were obtained. The results acquired at room temperature for C60 with face-centered cubic lattice are important for the description of the physical-mechanical properties of simple cubic lattice phase of C60 below 260 K (S. V. Lubenets, L. S. Fomenko, V. D. Natsik, and A. V. Rusakova, Fiz. Nizk. Temp. 45, 3 (2019) [Low Temp. Phys. 45, 1 (2019)]).


  • Open Access

    Synthesis and micromechanical properties of graphene oxide-based polymer nanocomposites

    by H. V. Rusakova, L. S. Fomenko, S. V. Lubenets, A. V. Dolbin, N. A. Vinnikov, R. M. Basnukaeva, M. V. Khlistyuck, A. V. Blyznyuk

    The authors have studied the effect of small (≤ 1 wt%) additions of thermally reduced graphene oxide on the microhardness and microindentation kinetics in two types of polymers: polystyrene (i.e. thermoplastic with a glass transition temperature of Tg ≈ 373 K) and polyester resin (i.e. thermosetting plastic, Tg ≈ 300 K). The room temperature creep of nanocomposites under an indenter is described using a three-element rheological Kelvin–Voigt model. The study determines the parameters of this model and how graphene oxide (GO) affects them. In a polystyrene nanocomposite with 0.3 wt % graphene oxide, unrelaxed and relaxed elastic moduli, and the modulus characterizing high-elastic deformation, increase by 11%, 40% and 87%, respectively, as compared to the initial polystyrene; at the same time, microhardness increases by 38% and 45% for the different series of samples. The results obtained indicate that the presence of graphene oxide in the nanocomposite severely restricts the mobility of molecular segments. The addition of 0.3 wt% graphene oxide to polyester resin is accompanied by an increase in the mechanical glass transition temperature of the resin by at least 5 K. This leads to a change in the relaxation state of this polymer: while at room temperature the polyester resin behaves like an elastomer, a polyester resin nanocomposite with 0.3 wt% graphene oxide exhibits glassy properties. At room temperature, the microhardness of polyester resin-glass fabric-graphene oxide nanocomposites with a GO content of 0.5 and 1 wt% increases by 20% and 80% respectively, as compared to that of a polyester resin-glass fabric composite. The authors have obtained the temperature dependences of the microhardness of nanocomposites with a polyester matrix in the range 77–298 K, and have also identified temperature regions where the microdeformation of composites is reversible, which is associated with the formation of crazes with a lower glass transition temperature.


  • Open Access

    Low-Temperature Features of the Micromechanical Properties of Polystyrene

    by H. V. Rusakova, L. S. Fomenko, S. V. Lubenets, V. D. Natsik

    The microindentation of thin polystyrene plates, which is an amorphous linear thermoplastic polymer with a glass transition temperature Tg ≈ 373 K, was carried out in the 77–295 K temperature range. A decrease in the temperature from 295 K to 140 K generated a two-fold linear increase in microhardness, which is in good agreement with the temperature dependence of the forced elasticity limit of polystyrene measured by other authors during uniaxial compression deformation. At temperatures of T = 77–140 K the local deformation of polystyrene was reversible: during heating to room temperature the impressions on the sample surface disappeared completely. Partial deformation reversibility was observed upon indentation in the temperature range of 140–190 K, but at indentation temperatures T > 190 K the impressions remained. The microstrain reversibility of polystyrene in nitrogen at, and close to, 77 K is due to the effect of the adsorption-active medium on the formation of crazes (fibrillar-porous nanostructures), the glass transition temperature of which is tens of degrees below that of bulk polymer.