TKT. S. Karthik

T. S. Karthik

*This is an algorithmically generated author record based on publicly available information.

T. S. Karthik has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Retracted
    Open Access

    [Retracted] A Comparative Study on Crack‐Healing Ability of Al2O3/SiC Structural Ceramic Composites Synthesized by Microwave Sintering and Conventional Electrical Sintering

    by Madhan Mohankumar, A. N. Shankar, T. S. Karthik, R. Saravanakumar, Hemakesavulu Oruganti, S. Venkatesa Prabhu, N. Rakesh

    This study was conducted to assess and compare the crack‐healing ability of conventional electrical sintered and microwave sintered Al2O3/x wt. % SiC (x = 5, 10, 15, and 20) structural ceramic composites. The crack‐healing ability of both conventional electrical sintered and microwave sintered specimens was studied by introducing a crack of ∼100 µm length by Vickers’s indentation and conducting a heat treatment at 1200°C for dwell time of 1 h in air. The flexural or bending strength of sintered, cracked, and crack‐healed specimens was determined by three‐point bending test, and the phase variations by X‐ray diffraction and SEM micrographs before and after crack‐healing of both the sintering methods were studied and compared. The results show that almost all the specimens recovered their strength after crack‐healing, but the strength of microwave sintered Al2O3/SiC structural ceramic composites has been shown to be better than that of conventional electrical sintered Al2O3/SiC structural ceramic composites. The microwave sintered crack‐healed Al2O3/10 wt. % SiC specimen shows higher flexural strength of 794 MPa, which was 105% when compared with conventional electrical sintered Al2O3/10 wt. % SiC and crack‐healed Al2O3/10 wt. % SiC specimen. It was found by X‐ray diffractogram that before crack‐healing, all the conventional electrical sintered samples have SiO2 phase which reduce the crack‐healing ability and microwave sintered samples with 15 and 20 wt. % SiC show lesser SiO2 phase and 5 and 10 wt. % SiC samples have no SiO2 phase before crack‐healing. However, after crack‐healing treatment, all the samples have distinct SiO2 phase along with Al2O3 and SiC phases. Microwave sintered Al2O3/10 wt. % SiC specimen cracks were fully healed which was evident in SEM micrographs.


  • Retracted
    Open Access

    [Retracted] Investigation on Dielectric Properties of Press Board Coated with Epoxy Resin, Quartz, and Rice Husk Ash

    by S. Banumathi, T. S. Karthik, M. Sasireka, Kiran Ramaswamy, J.R. Vishnu, M. K. Yuvan, R. R. Kavin, Sathish Kumar Shanmugam

    Epoxy resin mixed with rice husk ash and quartz powder increases its dielectric strength. This paper presents the dielectric properties of the press board coated with this epoxy mixture. In this work, the press board, which is used in the transformer, is coated with three components: epoxy resin, rice husk ash, and quartz powder. The nanometer‐sized quartz powder and rice husk ash are mixed in the particular ratio with the epoxy resin. The mixture of epoxy resin, quartz powder, and rice husk ash is coated on both sides of the press board. The dielectric constant, volume resistivity, and Tan Delta (dissipation factor) of the coated press board are compared with the noncoated press board. The results reveal that the coated board is having high dielectric constant and volume resistivity when compared to the noncoated board.